GRACO INC. S10595

GG LTX319

RAC X LTX TIP, SPRAY, 319

Graco LTX319 RAC X SwitchTip, 319

The Reverse-A-Clean (RAC) 319 RAC X SwitchTip is designed for narrow surfaces and thick materials. The 319 SwitchTip has a 0.019 inch orifice and produces a 6 to 8 inch fan. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 15
• Maximum Fan Width (in): 6
• Maximum Fan Width (mm): 203

• Maximum Flow Rate (GPM): 0.38
• Maximum Flow Rate (L/min): 1.44

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 6
• Minimum Fan Width (mm): 152

• Orifice Diameter (in): 0.019

• Pattern Size (in): 6 to 8
• Pattern Size (mm): 152.4 to 203.2

GG LTX419

RAC X LTX TIP, SPRAY, 419

Graco LTX419 RAC X SwitchTip, 419

The Reverse-A-Clean (RAC) 419 RAC X SwitchTip produces an 8 to 10 inch fan and has a 0.019 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 20
• Maximum Fan Width (in): 8
• Maximum Fan Width (mm): 254

• Maximum Flow Rate (GPM): 0.38
• Maximum Flow Rate (L/min): 1.44

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 8
• Minimum Fan Width (mm): 203

• Orifice Diameter (in): 0.019

• Pattern Size (in): 8 to 10
• Pattern Size (mm): 203.2 to 254

GG LTX227

RAC X LTX TIP, SPRAY, (227)

Graco LTX227 RAC X SwitchTip, 227

The Reverse-A-Clean (RAC) 227 RAC X SwitchTip is designed for narrower surfaces and thicker materials. The 227 SwitchTip has a 0.027 inch orifice and produces a 4 to 6 inch fan. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market
  • Longest lasting fan pattern
  • Highest quality finish with a consistent spray pattern
• Easy to Identify Tip Size
  • Large raised tip size numbers are always legible - even when covered with paint
• Superior Tip Design
  • Locking tab ensures tip stays securely in guard
  • Snaps tip in spray or reverse position
  • OneSeal tip gasket installs with no tools
  • Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 10
• Maximum Fan Width (in): 4
• Maximum Fan Width (mm): 152

• Maximum Flow Rate (GPM): 0.77
• Maximum Flow Rate (L/min): 2.91

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 4
• Minimum Fan Width (mm): 102

• Orifice Diameter (in): 0.027

• Pattern Size (in): 4 to 6
• Pattern Size (mm): 101.6 to 152.4

GG LTX315

RAC X LTX TIP, SPRAY, 315

Graco LTX315 RAC X SwitchTip, 315

The Reverse-A-Clean (RAC) 315 RAC X SwitchTip is designed for narrow surfaces. The 315 SwitchTip has a 0.015 inch orifice and produces a 6 to 8 inch fan. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Latex Paint, Latex Stain, Oil-Based Paint, Oil-Based Stain

• For Use With: RAC X HandTite Tip Guard

• Material: Tungsten Carbide

• Maximum Fan Width (cm): 15
• Maximum Fan Width (in): 6

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Orifice Diameter (in): 0.015

GG LTX415

RAC X LTX TIP, SPRAY, 415

Graco LTX415 RAC X SwitchTip, 415

The Reverse-A-Clean (RAC) 415 RAC X SwitchTip produces an 8 to 10 inch fan and has a 0.015 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Latex Paint, Latex Stain, Oil-Based Paint, Oil-Based Stain

• For Use With: RAC X HandTite Tip Guard

• Material: Tungsten Carbide

• Maximum Fan Width (cm): 20
• Maximum Fan Width (in): 8

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Orifice Diameter (in): 0.015

GG LTX425

RAC X LTX TIP, SPRAY, (425)

Graco LTX425 RAC X SwitchTip, 425

The Reverse-A-Clean (RAC) 425 RAC X SwitchTip produces an 8 to 10 inch fan and has a 0.025 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 20
• Maximum Fan Width (in): 8
• Maximum Fan Width (mm): 254

• Maximum Flow Rate (GPM): 0.67
• Maximum Flow Rate (L/min): 2.54

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 8
• Minimum Fan Width (mm): 203

• Orifice Diameter (in): 0.025

• Pattern Size (in): 8 to 10
• Pattern Size (mm): 203.2 to 254

GG LPA-190-SK

KIT,SLAVE PUMP SEAL

KIT INCLUDES: O-RING, O-RING, SILICONE, 2-014 [QTY. 2], O-RING, O-RING, SILICONE, 2-110 [QTY. 1], O-RING, O-RING, SILICONE, 2-010 [QTY. 1], SEAL, RADIAL [QTY. 2], SEAL, RADIAL [QTY. 1], GUIDE, PISTON [QTY. 1], WASHER, CRUSH, POLY, .343ID [QTY. 1], SEAT, BALL, 7/16DIA. [QTY. 1], WIPER, FELT [QTY. 2], O-RING, 003, VITON EXTREME [QTY. 1]

GG LTX115

RAC X LTX TIP, SPRAY, (115)

Graco LTX115 RAC X SwitchTip, 115

The Reverse-A-Clean (RAC) 115 RAC X SwitchTip is designed for narrower surfaces. The 115 SwitchTip has a 0.015 inch orifice and produces a 2 to 4 inch fan. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 5
• Maximum Fan Width (in): 2
• Maximum Fan Width (mm): 102

• Maximum Flow Rate (GPM): 0.24
• Maximum Flow Rate (L/min): 0.91

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 2
• Minimum Fan Width (mm): 51

• Orifice Diameter (in): 0.015

• Pattern Size (in): 2 to 4
• Pattern Size (mm): 50.8 to 101.6

GG LTX311

RAC X LTX TIP, SPRAY, 311

Graco LTX311 RAC X SwitchTip, 311

The Reverse-A-Clean (RAC) 311 RAC X SwitchTip is designed for narrow surfaces and thin materials. The 311 SwitchTip has a 0.011 inch orifice and produces a 6 to 8 inch fan. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Clear Coating, Lacquer, Oil-Based Stain

• For Use With: RAC X HandTite Tip Guard

• Material: Tungsten Carbide

• Maximum Fan Width (cm): 15
• Maximum Fan Width (in): 6

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Orifice Diameter (in): 0.011

GG LTX313

RAC X LTX TIP, SPRAY, 313

Graco LTX313 RAC X SwitchTip, 313

The Reverse-A-Clean (RAC) 313 RAC X SwitchTip is designed for narrow surfaces. The 313 SwitchTip has a 0.013 inch orifice and produces a 6 to 8 inch fan. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Latex Paint, Latex Stain, Oil-Based Paint, Oil-Based Stain

• For Use With: RAC X HandTite Tip Guard

• Material: Tungsten Carbide

• Maximum Fan Width (cm): 15
• Maximum Fan Width (in): 6

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Orifice Diameter (in): 0.013

GG LP621

RAC X LP TIP, SPRAY, (621)

Graco LP621 Low Pressure RAC X LP SwitchTip, 621

Spray at up to 50% lower pressure with the Reverse-A-Clean (RAC) 621 Low Pressure (LP) RAC X SwitchTip. This low pressure tip produces a 12 to 14 inch fan pattern and has a 0.021 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Less Prep & Cleanup Time

  Less mess with less overspray

  Put the paint where you want it

• Easiest Pattern Overlap

  Softer spray fan pattern

  Easy to apply any material to any surfance

  Consistent blended finish quality

• Extended Life

  Spraying at half pressure doubles tip life

  Reduced sprayer maintenance - up to 2X life

• Best Tip on the Market

  Works with any airless sprayer

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LP SwitchTip

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 30
• Maximum Fan Width (in): 12
• Maximum Fan Width (mm): 356

• Maximum Flow Rate (GPM): 0.47
• Maximum Flow Rate (L/min): 1.78

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 12
• Minimum Fan Width (mm): 305

• Orifice Diameter (in): 0.021

GG LPA-131

GG LPA-190-RK

GG LPA-165

GG LPA-126

SEAL,RADIAL

GG LPA-129

GG L60T32

PRO XP GUN, ES, 60KV, ROUND MEDIUM

Graco L60T32 Pro Xp60 Air Spray Manual Electrostatic Gun, 60 kV, standard display, round spray nozzle/air cap medium pattern

The round spray nozzle and medium pattern air cap boost the transfer efficiency of this 60 kV electrostatic spray gun.

• Bell-like round spray and electrostatics maximize wrap around cylindrical objects.
• Round spray components form small to medium patterns at lower fluid flow rates with less airflow. This improves finish quality on small, light objects.

• Model: Pro Xp
• Series: 60
• Product Series: A

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Gender: Male
• Air Inlet Thread Type: NPSM

• Application: Electrostatic, Standard
• Applicator Type: Manual

• Coating Type: Standard

• Compatible Paint Type: Automotive, Base Coat, Clear Coat, Enamels, High Solids, Metallics, Plural Component Materials, Primers, Solventborne, Urethanes

• Display Type: Standard

• Fluid Inlet Size (in): 3/8
• Fluid Inlet Thread Gender: Male
• Fluid Inlet Thread Type: NPSM

• Gun Activation: Manual
• Gun Type: Electrostatic
• Gun Weight (g): 600
• Gun Weight (kg): 0.6
• Gun Weight (lb): 1.32
• Gun Weight (oz): 21.16

• Includes: Round Spray air cap, Nozzle, Tool Kit, Gun Cover, Exhaust Tube

• Maximum Fluid Pressure (bar): 7.0
• Maximum Fluid Pressure (kg/cm 2): 7.14
• Maximum Fluid Pressure (kPa): 700
• Maximum Fluid Pressure (MPa): 0.7
• Maximum Fluid Pressure (psi): 100
• Maximum Fluid Temperature ( degree C): 48
• Maximum Fluid Temperature ( degree F): 120

• Maximum Fluid Pressure (bar): 7.0
• Maximum Fluid Pressure (kg/cm 2): 7.14
• Maximum Fluid Pressure (kPa): 700
• Maximum Fluid Pressure (MPa): 0.7
• Maximum Fluid Pressure (psi): 100
• Maximum Fluid Temperature ( degree C): 48
• Maximum Fluid Temperature ( degree F): 120

• Maximum Paint Resistivity (megohm/cm): Infinity

• Minimum Paint Resistivity (megohm/cm): 25

• Overall Length (cm): 24.13
• Overall Length (in): 9.5
• Overall Length (mm): 241.3

GG H85M10

PRO XP GUN, ES, 85KV, AA, SMART

Graco H85M10 Pro Xp85 Air Assist Manual Electrostatic Gun, 85 kV, with smart display, standard coatings, includes AEM or AEF tip of choice

Pro Xp85 kV air-assist gun maximizes transfer efficiency and lowers cost of ownership. Pro Xp85 AA gun line includes Standard and Smart models.

• High quality spray performance with a one-piece aircap and variety of spray tips
• Alternator speed indicator light ensures your turbine speed is running at the correct level
• Smart Controls help you analyze performance, adapt to your voltage needs and make troubleshooting easier
• Internal power supply reduces operator fatigue with no heavy cords to slow you done
• Rugged, dependable design supported by a three year warranty
• Every gun is tested and delivered with a certificate indicating the spray pattern, mechanical performance and electrical performance meets Gracos requirements

• Model: Pro Xp
• Series: 85

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Gender: Male
• Air Inlet Thread Type: NPSM

• Application: Electrostatic, Standard
• Applicator Type: Manual

• Coating Type: Standard

• Compatible Paint Type: Epoxy, High Solids, Lacquers, Plural Component Materials, Polyurethanes, Solvent borne, Urethanes, UV Curing, Varnishes,

• Display Type: Smart

• Fluid Inlet Size (in): 1/4
• Fluid Inlet Thread Gender: Male
• Fluid Inlet Thread Type: NPSM

• Gun Activation: Manual
• Gun Type: Electrostatic
• Gun Weight (g): 728
• Gun Weight (kg): 0.73
• Gun Weight (lb): 1.6
• Gun Weight (oz): 25.68

• Includes: Smart Display, Tip Guard Air Cap, Tip of Choice, Tool Kit, Gun Cover, Exhaust Tube,

• Maximum Fluid Pressure (bar): 210
• Maximum Fluid Pressure (kg/cm 2): 214.14
• Maximum Fluid Pressure (kPa): 21000
• Maximum Fluid Pressure (MPa): 21
• Maximum Fluid Pressure (psi): 3000
• Maximum Fluid Temperature ( degree C): 48
• Maximum Fluid Temperature ( degree F): 120

• Maximum Fluid Pressure (bar): 210
• Maximum Fluid Pressure (kg/cm 2): 214.14
• Maximum Fluid Pressure (kPa): 21000
• Maximum Fluid Pressure (MPa): 21
• Maximum Fluid Pressure (psi): 3000
• Maximum Fluid Temperature ( degree C): 48
• Maximum Fluid Temperature ( degree F): 120

• Maximum Paint Resistivity (megohm/cm): Infinity

• Minimum Paint Resistivity (megohm/cm): 3

• Overall Length (cm): 27.18
• Overall Length (in): 10.7
• Overall Length (mm): 271.8

GG L40T14

PRO XP GUN, ES, 40KV, GROUND POINT

Graco L40T14 Pro Xp40 Air Spray Manual Electrostatic Gun, 40 kV Booster, 0.055 in (1.5 mm) nozzle, standard display

Get the transfer efficiency of a 60 kV electrostatic air spray gun in the compact size of a 40 kV gun. The smaller and lighter ergonomics make it ideal for operators who work in tight spaces.

• Easily adjust gun performance with large, simple-to-use, control knobs.
• Durable components are backed by a three-year warranty and A+ Service.
• Made in the USA
• Every gun is tested and delivered with a certificate indicating the spray pattern, mechanical performance and electrical performance meets Gracos requirements

• Model: Pro Xp
• Series: 40

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Gender: Male
• Air Inlet Thread Type: NPSM

• Application: Electrostatic, Standard
• Applicator Type: Manual

• Coating Type: Standard

• Compatible Paint Type: Automotive, Base Coat, Clear Coat, Enamels, High Solids, Metallics, Plural Component Materials, Primers, Solvent borne, Urethanes

• Display Type: Standard

• Fluid Inlet Size (in): 3/8
• Fluid Inlet Thread Gender: Male
• Fluid Inlet Thread Type: NPSM

• Gun Activation: Manual
• Gun Type: Electrostatic
• Gun Weight (g): 560
• Gun Weight (kg): 0.56
• Gun Weight (lb): 1.23
• Gun Weight (oz): 19.75

• Includes: Air Cap, Nozzle, Tool Kit, Gun Cover, Exhaust Tube

• Maximum Fluid Pressure (bar): 7.0
• Maximum Fluid Pressure (kg/cm 2): 7.14
• Maximum Fluid Pressure (kPa): 700
• Maximum Fluid Pressure (MPa): 0.7
• Maximum Fluid Pressure (psi): 100
• Maximum Fluid Temperature ( degree C): 48
• Maximum Fluid Temperature ( degree F): 120

• Maximum Fluid Pressure (bar): 7.0
• Maximum Fluid Pressure (kg/cm 2): 7.14
• Maximum Fluid Pressure (kPa): 700
• Maximum Fluid Pressure (MPa): 0.7
• Maximum Fluid Pressure (psi): 100
• Maximum Fluid Temperature ( degree C): 48
• Maximum Fluid Temperature ( degree F): 120

• Maximum Paint Resistivity (megohm/cm): Infinity

• Minimum Paint Resistivity (megohm/cm): 25

• Nozzle Size (cm): 0.15
• Nozzle Size (in): 0.055
• Nozzle Size (mm): 1.5

• Overall Length (cm): 22.1
• Overall Length (in): 8.7
• Overall Length (mm): 221

GG L40M10

PRO XP GUN,ES,40KV,SMART

Graco L40M10 Pro Xp40 Air Spray Manual Electrostatic General Gun Model, 40 kV, 0.055 in (1.5 mm) nozzle, smart display, standard coatings

Available in 40 kV, this general model is the smallest profile gun with an internal power supply on the market. It comes with smart technology that empowers you to maximize efficiency and productivity.

• Smart controls help you analyze performance, adapt to your voltage needs and make troubleshooting easier.
• Painters experience less muscle strain and fatigue when spraying with the ergonomic, lightweight electrostatic gun model.
• Electrostatic air spray gun meets strict requirements for spray pattern, mechanical and electrical performance. Durable, easy-to-repair components are backed by a three-year warranty and A+ Service.

• Model: Pro Xp
• Series: 40
• Product Series: A

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Gender: Male
• Air Inlet Thread Type: NPSM

• Application: Electrostatic, Standard
• Applicator Type: Manual

• Coating Type: Standard

• Compatible Paint Type: Automotive, Base Coat, Clear Coat, Enamels, High Solids, Metallics, Plural Component Materials, Primers, Solventborne, Urethanes

GG L500CS

LOWER, CM500 SEVERE DUTY

Graco L500CS Carbon Steel Severe Duty Check-Mate 500 Lower

• Model: Check-Mate

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Bonding, Sealing, Gasketing, Potting, Encapsulation, Molding, Spray, Fluid Transfer, Unloading, Underfill

• Fluid Outlet Size (in): 1-1/2
• Fluid Outlet Thread Gender: Male
• Fluid Outlet Thread Type: NPT

• For Use With: Check-Mate Pump Packages

• Maximum Flow Rate (GPM): 8

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 500

• Maximum Pump Speed (CPM): 60

• Maximum Working Pressure (psi): 3900

GG L60T16

PRO XP GUN, ES, 60KV, HC

Graco L60T16 Pro Xp60 Air Spray Manual Electrostatic High Conductivity Gun, 60 kV, 0.055 in (1.5 mm) precision high wear nozzle, standard display

This 60 kV high conductivity model produces material savings and excellent finish quality with a small, light gun body that's easy to spray.

• Metal tip precision high-wear nozzle, high-wear electrode, and more durable fluid tube improve longevity.
• Removable black fluid tube cover allows operator to see fluid movement.
• Smart Controls help you analyze performance, adapt to your voltage needs and make troubleshooting easier
• Made in the USA

• Model: Pro Xp
• Series: 60

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Gender: Male
• Air Inlet Thread Type: NPSM

• Application: Electrostatic, High Conductivity, High Wear
• Applicator Type: Manual

• Coating Type: Abrasive, Metallic, High Conductivity, High Wear

• Compatible Paint Type: Automotive, Base Coat, Clear Coat, Enamels, High Solids, Metallics, Plural Component Materials, Primers, Solvent borne, Urethanes

• Display Type: Standard

• Fluid Inlet Size (in): 3/8
• Fluid Inlet Thread Gender: Male
• Fluid Inlet Thread Type: NPSM

• Gun Activation: Manual
• Gun Type: Electrostatic
• Gun Weight (g): 600
• Gun Weight (kg): 0.6
• Gun Weight (lb): 1.32
• Gun Weight (oz): 21.16

• Includes: Air Cap, Nozzle, Tool Kit, Gun Cover, Exhaust Tube

• Maximum Fluid Pressure (bar): 7.0
• Maximum Fluid Pressure (kg/cm 2): 7.14
• Maximum Fluid Pressure (kPa): 700
• Maximum Fluid Pressure (MPa): 0.7
• Maximum Fluid Pressure (psi): 100
• Maximum Fluid Temperature ( degree C): 48
• Maximum Fluid Temperature ( degree F): 120

• Maximum Fluid Pressure (bar): 7.0
• Maximum Fluid Pressure (kg/cm 2): 7.14
• Maximum Fluid Pressure (kPa): 700
• Maximum Fluid Pressure (MPa): 0.7
• Maximum Fluid Pressure (psi): 100
• Maximum Fluid Temperature ( degree C): 48
• Maximum Fluid Temperature ( degree F): 120

• Maximum Paint Resistivity (megohm/cm): 25

• Minimum Paint Resistivity (megohm/cm): 1

• Nozzle Size (cm): 0.15
• Nozzle Size (in): 0.055
• Nozzle Size (mm): 1.5

• Overall Length (cm): 24.13
• Overall Length (in): 9.5
• Overall Length (mm): 241.3

GG L290C2

GG L100SM

GG L220C1

GG L200CS

LOWER, CM200 SEVERE DUTY

Graco L200CS Carbon Steel Severe Duty Check-Mate 200 Lower

• Model: Check-Mate

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Bonding, Sealing, Gasketing, Potting, Encapsulation, Molding, Spray, Fluid Transfer, Unloading, Underfill

• Fluid Outlet Size (in): 1
• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: NPT

• For Use With: Check-Mate Pump Packages

• Maximum Flow Rate (GPM): 3.2

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 200

• Maximum Pump Speed (CPM): 60

• Maximum Working Pressure (psi): 6200

GG L220C2

GG L250CS

LOWER, CM250 SEVERE DUTY

Graco L250CS Carbon Steel Severe Duty Check-Mate 250 Lower

• Model: Check-Mate

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Bonding, Sealing, Gasketing, Potting, Encapsulation, Molding, Spray, Fluid Transfer, Unloading, Underfill

• Fluid Outlet Size (in): 1
• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: NPT

• For Use With: Check-Mate Pump Packages

• Maximum Flow Rate (GPM): 4

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 250

• Maximum Pump Speed (CPM): 60

• Maximum Working Pressure (psi): 6200

GG L200CM

LOWER, CM200 MAXLIFE

Graco L200CM Carbon Steel MaxLife Check-Mate 200 Lower

• Model: Check-Mate

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Bonding, Sealing, Gasketing, Potting, Encapsulation, Molding, Spray, Fluid Transfer, Unloading, Underfill

• Fluid Outlet Size (in): 1
• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: NPT

• For Use With: Check-Mate Pump Packages

• Maximum Flow Rate (GPM): 3.2

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 200

• Maximum Pump Speed (CPM): 60

• Maximum Working Pressure (psi): 6200

GG L180C2

GG L200SM

GG L200SS

LOWER, CM200 SEVERE DUTY SST

Graco L200SS Stainless Steel Severe Duty Check-Mate 200 Lower

• Model: Check-Mate

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Bonding, Sealing, Gasketing, Potting, Encapsulation, Molding, Spray, Fluid Transfer, Unloading, Underfill

• Fluid Outlet Size (in): 1
• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: NPT

• For Use With: Check-Mate Pump Packages

• Maximum Flow Rate (GPM): 3.2

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 200

• Maximum Pump Speed (CPM): 60

• Maximum Working Pressure (psi): 6200

GG L040S4

LOWER, CHEMICAL, 040, SST, UCUP

Graco L040S4 Z-Pump, 40 cc, Severe Duty, S4

Z-Pumps are positive displacement pump components for use with the Graco and meter, mix, and dispense systems and are ideal for two-component sealant and adhesives requiring precision ratio, flow, and volume controls.

• Severe Duty coatings and 1/2 inch (1.27 cm) checks easily manage material wear from silicones, sealants, epoxies, and structural adhesives.
• Precision control eliminates pressure spikes and guarantees on ratio dispense.
• Pump seals are the only wear parts, which reduces maintenance downtime and repair costs.

• Model: Z-Pump
• Series: S4

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Industrial

• Ball Check Size (in): 1/2
• Ball Material: Silicon Nitride

• Coating Type: Severe Duty

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 1.905
• Fluid Inlet Size (in): 3/4
• Fluid Inlet Thread Gender: Female
• Fluid Inlet Thread Type: NPT

• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: SAE

• For Use With: EFR, HFR

• Maximum Flow Rate (GPM): 0.63

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 40

• Maximum Pump Speed (CPM): 60

• Maximum Viscosity (cP): 3000000

GG K70FH0

KING SPRAYER, 70:1, H-P, BF, HD, BARE

Graco K70FH0 King 70:1 Sprayer, Integrated Filter, Heavy Duty Cart, Air Controls, Siphon Kit

High-quality, high-volume, high-pressure. The Graco King pneumatic airless sprayers are the most powerful machines for protective coatings. The system provides the applicator output values, pressure ratios and pumping capacities never seen before. The Graco King units are designed to withstand the harshest environmental conditions and easily handle the toughest protective coatings and corrosion control applications. With 10 different ratios available, there is a sprayer with the correct pressure and flow characteristics for your application.

• Simple Maintenance

  This air motor has 50% less parts when compared to the NXT valve, making maintenance and troubleshooting easy.

  All motor parts are easily accessible and require simple maintenance.

  • Improved Icing Performance

    The newly designed poppets and external pilot lines virtually eliminate pilot valve freezing that can result in an instant stop.

    The icing potential has been reduced by up to 70%

    • Less Pulsation

      With more than 145% higher exhaust capacity in the air valve, youll achieve a faster, smoother changeover.

      Eliminating the winkin your pattern - it is a difference you will feel.

    • New Air Motor

      Multi gun capabilities Graco's powerful new air motor lets you use multiple guns with almost no perceivable pulsation. A new manifold has been designed to simplify the installation of multiple guns.

    
    

    • Model: King
    • Air Inlet Size (in): 1
    • Air Inlet Thread Gender: Female
    • Air Inlet Thread Type: NPT
    • Approved for Hazardous Locations: Yes
    • Compatible Material: Protective Coating
    • Control Type: Fixed Ratio
    • Convertible: Non-Convertible
    • Features: Exposed Thermally Isolated Poppets, De-Icing Valve, Tool Box, Trusted XL Motor, Protective Rod Guard, Robust Air Controls, Xtreme Lowers, Improved Siphon Hose, Cart With Wheels
    • Fluid Inlet Size (in): 1-1/4
    • Fluid Inlet Size (mm): 31.75
    • Fluid Inlet Thread Gender: Male
    • Fluid Inlet Thread Type: NPT
    • Fluid Outlet Size (in): 1/2
    • Fluid Outlet Size (mm): 12.7
    • Fluid Outlet Thread Gender: Female
    • Fluid Outlet Thread Type: NPT
    • Frame Configuration: Heavy-Duty Cart
    • Gun Model: No Applicator
    • Includes: Pump, Lower, Motor, Standard Filter, Heavy Duty Cart, Air Controls, Siphon Kit
    • Lower Type: Integrated Filter
    • Material Application: Paints, Primers
    • Maximum Air Inlet Pressure (psi): 150
    • Maximum Air Pressure (bar): 7
    • Maximum Air Pressure (kPa): 700
    • Maximum Air Pressure (psi): 100
    • Maximum Fluid Working Pressure (psi): 7250
    • Maximum Sound Pressure Level (dB(A)): 81.48
    • Maximum Tip Size (in): Variable
    • Maximum Working Pressure (bar): 500
    • Maximum Working Pressure (kPa): 50000
    • Maximum Working Pressure (MPa): 50
    • Maximum Working Pressure (psi): 7250
    • Motor Type: XL High Performance
    • Number of Guns:

GG H60T18

PRO XP GUN, ES, 60KV, AA, WB

Graco H60T18 Pro Xp60 AA WB Manual Air-Assist Spray Gun, 60 kV, standard display, for waterborne coatings

Excellent, air assisted pattern control eliminates defects for a fine finish with waterborne material.

• This 60 kV model is the smallest and lightest air assist gun on the market.
• Air-assist aircaps use less air, lowering your energy bill.
• Made in the USA
• Fan adjust pattern control reduces overspray by changing the fan pattern width according to the size of the part - improving quality and saving you money
• Every gun is tested and delivered with a certificate indicating the spray pattern, mechanical performance and electrical performance meets Gracos requirements

• Model: Pro Xp
• Series: 60

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Gender: Male
• Air Inlet Thread Type: NPSM

• Application: Electrostatic, Waterborne
• Applicator Type: Manual

• Coating Type: Waterborne

• Compatible Paint Type: Epoxy, High Solids, Lacquers, Latex, Plural Component Materials, Polyurethanes, Urethanes, UV Curing, Varnishes, Waterborne

• Display Type: Standard

• Fluid Inlet Size (in): 1/4
• Fluid Inlet Thread Gender: Male
• Fluid Inlet Thread Type: NPSM

• Gun Activation: Manual
• Gun Type: Electrostatic
• Gun Weight (g): 660
• Gun Weight (kg): 0.66
• Gun Weight (lb): 1.46
• Gun Weight (oz): 23.28

• Includes: Tip Guard Air Cap, Tip of Choice, Tool Kit, Gun Cover, Exhaust Tube

• Maximum Fluid Pressure (bar): 210
• Maximum Fluid Pressure (kg/cm 2): 214.14
• Maximum Fluid Pressure (kPa): 21000
• Maximum Fluid Pressure (MPa): 21
• Maximum Fluid Pressure (psi): 3000
• Maximum Fluid Temperature ( degree C): 48
• Maximum Fluid Temperature ( degree F): 120

• Maximum Fluid Pressure (bar): 210
• Maximum Fluid Pressure (kg/cm 2): 214.14
• Maximum Fluid Pressure (kPa): 21000
• Maximum Fluid Pressure (MPa): 21
• Maximum Fluid Pressure (psi): 3000
• Maximum Fluid Temperature ( degree C): 48
• Maximum Fluid Temperature ( degree F): 120

• Maximum Paint Resistivity (megohm/cm): 1

• Minimum Paint Resistivity (megohm/cm): 0

• Overall Length (cm): 24.64
• Overall Length (in): 9.7
• Overall Length (mm): 246.4

GG H60T10

PRO XP GUN,ES,60KV,AA

Graco H60T10 Pro Xp60 Air Assist Manual Electrostatic Gun, 60 kV, with standard display, standard coatings, includes AEM or AEF tip of choice

Pro Xp60 kV air-assist gun is the smallest and lightest electrostatic air-assist gun on the market - delivering a consistent, high quality finish every time you spray. Pro Xp60 AA gun line includes Standard, Smart and Waterborne models.

• High quality spray performance with a one-piece aircap and variety of spray tips
• Transfer efficiency is improved over conventional air-assist guns
• Made in the USA The smallest profile gun with internal power supply on the market - 1 inch (2.5 cm) shorter and 4 oz (110 g) lighter
• Fan adjust pattern control reduces overspray by changing the fan pattern width according to the size of the part - improving quality and saving you money
• Every gun is tested and delivered with a certificate indicating the spray pattern, mechanical performance and electrical performance meets Graco's requirements

• Model: Pro Xp
• Series: 60

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Gender: Male
• Air Inlet Thread Type: NPSM

• Application: Electrostatic, Standard
• Applicator Type: Manual

• Coating Type: Standard

• Compatible Paint Type: Epoxy, High Solids, Lacquers, Latex, Plural Component Materials, Polyurethanes, Urethanes, UV Curing, Varnishes, Waterborne

GG HEM004

LDX SERIES REEL, HOSE, 1/2in X 50', OIL

Graco HEM004 LDX Series, Oil, 1/2 in (13 mm) Inlet, 1/2 in X 50 ft (13 mm X 15 m) Hose, NPT

Graco's industrial-grade LDX hose reel offers incredible value for cost-conscious workshops. Its all-metal frame and specially crafted, long-lasting components provide consistent release and retraction.

• Dual Pedestal Frame - Ribbed metal for increased stability and robustness.
• External Swivel Housing - Quickly access swivel seal for faster repairs.
• Ball Bearing Swivel - Swivel designed with internal ball bearings reduces friction and ensures smooth operation.
• Large Hose Capacity with Small Profile - Compact design accommodates up to a 50 foot (15 meter) hose to meet a wide variety of application requirements.

• Model: LDX

• Application: Oil

• Color: Grey

• Dry Weight (lb): 48

• Frame Type: Dual Pedestal

• Hose Inside Diameter (in): 1/2
• Hose Inside Diameter (mm): 12.7
• Hose Length (ft): 50
• Hose Length (m): 15

• Hose Reel Type: Reel with Hose
• Includes Hose: Yes
• Inlet Size (in): 1/2
• Inlet Size (mm): 12.7

• Inlet Thread Gender: Male
• Inlet Thread Type: NPT

• Maximum Temperature ( degree C): 100
• Maximum Temperature ( degree F): 212

• Maximum Working Pressure (psi): 1500

• Minimum Temperature ( degree C): -40
• Minimum Temperature ( degree F): -40

• Mount Location: Truck Mount, Bench Mount

• Outlet Size (in): 1/2
• Outlet Size (mm): 12.7
• Outlet Thread Gender: Male
• Outlet Thread Type: NPT

• Overall Height (in): 19
• Overall Height (mm): 483
• Overall Length (in): 17.5
• Overall Length (mm): 445
• Overall Width (in): 9.4
• Overall Width (mm): 239

• Recommended Environment: Indoor
• Recommended Fluid Type: Oil

GG HEL010

LDX SERIES REEL, HOSE, 3/8in X 50', A/W

Graco HEL010 LDX Series, Air/Water/Antifreeze/WWS, 3/8 in (10 mm) Inlet, 3/8 in X 50 ft (10 mm X 15 m) Hose, NPT

Graco's industrial-grade LDX hose reel offers incredible value for cost-conscious workshops. Its all-metal frame and specially crafted, long-lasting components provide consistent release and retraction.

• Dual Pedestal Frame - Ribbed metal for increased stability and robustness.
• External Swivel Housing - Quickly access swivel seal for faster repairs.
• Ball Bearing Swivel - Swivel designed with internal ball bearings reduces friction and ensures smooth operation.
• Large Hose Capacity with Small Profile - Compact design accommodates up to a 50 foot (15 meter) hose to meet a wide variety of application requirements.

• Model: LDX

• Application: Air, Water, Antifreeze, WWS

• Color: Grey

• Dry Weight (lb): 40.7

• Frame Type: Dual Pedestal

• Hose Inside Diameter (in): 3/8
• Hose Inside Diameter (mm): 9.525
• Hose Length (ft): 50
• Hose Length (m): 15

• Hose Reel Type: Reel with Hose
• Includes Hose: Yes
• Inlet Size (in): 3/8
• Inlet Size (mm): 9.525

• Inlet Thread Gender: Male
• Inlet Thread Type: NPT

• Maximum Temperature ( degree C): 65
• Maximum Temperature ( degree F): 149

• Maximum Working Pressure (psi): 300

• Minimum Temperature ( degree C): -26
• Minimum Temperature ( degree F): -14.8

• Mount Location: Truck Mount, Bench Mount

• Outlet Size (in): 3/8
• Outlet Size (mm): 9.525
• Outlet Thread Gender: Male
• Outlet Thread Type: NPT

• Overall Height (in): 19
• Overall Height (mm): 483
• Overall Length (in): 17.5
• Overall Length (mm): 445
• Overall Width (in): 9.4
• Overall Width (mm): 239

• Recommended Environment: Indoor
• Recommended Fluid Type: Air, Water, Antifreeze, WWS

GG L060SM

LOWER, SM060 MAXLIFE SST

Graco L060SM Stainless Steel MaxLife Check-Mate 60 Lower

• Model: Check-Mate

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Bonding, Sealing, Gasketing, Potting, Encapsulation, Molding, Spray, Fluid Transfer, Unloading, Underfill

• Fluid Outlet Size (in): 3/4
• Fluid Outlet Thread Gender: Male
• Fluid Outlet Thread Type: NPT

• For Use With: Check-Mate Pump Packages

• Maximum Flow Rate (GPM): 0.9

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 60

• Maximum Pump Speed (CPM): 60

• Maximum Working Pressure (psi): 6100

GG L050S1

LOWER, CHEMICAL, 50, SST, UCUP

Graco L050S1 Z-Pump, 50 cc, Severe Duty, S1

Z-Pumps are positive displacement pump components for use with the Graco meter, mix, and dispense systems and are ideal for two-component sealant and adhesives requiring precision ratio, flow, and volume controls.

• Severe Duty coatings and 1 inch (2.54 cm) checks easily manage material wear from silicones, sealants, epoxies, foam, and structural adhesives.
• Precision control eliminates pressure spikes and guarantees on ratio dispense.
• Pump seals are the only wear parts, which reduces maintenance downtime and repair costs.

• Model: Z-Pump
• Series: S1

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Industrial

• Ball Check Size (in): 1
• Ball Material: Silicon Nitride

• Coating Type: Severe Duty

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 1.905
• Fluid Inlet Size (in): 3/4
• Fluid Inlet Thread Gender: Female
• Fluid Inlet Thread Type: NPT

• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: SAE

• For Use With: HFR

• Maximum Flow Rate (GPM): 0.79

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 50

• Maximum Pump Speed (CPM): 60

• Maximum Viscosity (cP): 3000000

GG L100S4

LOWER, CHEMICAL, 100, SST, UCUP

Graco L100S4 Z-Pump, 100 cc, Severe Duty, S4

Z-Pumps are positive displacement pump components for use with the Graco and meter, mix, and dispense systems and are ideal for two-component sealant and adhesives requiring precision ratio, flow, and volume controls.

• Severe Duty coatings and 1/2 inch (1.27 cm) checks easily manage material wear from silicones, sealants, epoxies, and structural adhesives.
• Precision control eliminates pressure spikes and guarantees on ratio dispense.
• Pump seals are the only wear parts, which reduces maintenance downtime and repair costs.

• Model: Z-Pump
• Series: S4

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Industrial

• Ball Check Size (in): 1/2
• Ball Material: Silicon Nitride

• Coating Type: Severe Duty

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 1.905
• Fluid Inlet Size (in): 3/4
• Fluid Inlet Thread Gender: Female
• Fluid Inlet Thread Type: NPT

• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: SAE

• For Use With: EFR, HFR

• Maximum Flow Rate (GPM): 1.59

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 100

• Maximum Pump Speed (CPM): 60

• Maximum Viscosity (cP): 3000000

GG L100CS

LOWER, CM100 SEVERE DUTY

Graco L100CS Carbon Steel Severe Duty Check-Mate 100 Lower

• Model: Check-Mate

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Bonding, Sealing, Gasketing, Potting, Encapsulation, Molding, Spray, Fluid Transfer, Unloading, Underfill

• Fluid Outlet Size (in): 3/4
• Fluid Outlet Thread Gender: Male
• Fluid Outlet Thread Type: NPT

• For Use With: Check-Mate Pump Packages

• Maximum Flow Rate (GPM): 1.6

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 100

• Maximum Pump Speed (CPM): 60

• Maximum Working Pressure (psi): 6300

GG L060CS

LOWER, CM060 SEVERE DUTY

Graco L060CS Carbon Steel Severe Duty Check-Mate 60 Lower

• Model: Check-Mate

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Bonding, Sealing, Gasketing, Potting, Encapsulation, Molding, Spray, Fluid Transfer, Unloading, Underfill

• Fluid Outlet Size (in): 3/4
• Fluid Outlet Thread Gender: Male
• Fluid Outlet Thread Type: NPT

• For Use With: Check-Mate Pump Packages

• Maximum Flow Rate (GPM): 0.9

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 60

• Maximum Pump Speed (CPM): 60

• Maximum Working Pressure (psi): 6100

GG L020S4

LOWER, CHEMICAL, 020, SST, UCUP

Graco L020S4 Z-Pump, 20 cc, Severe Duty, S4

Z-Pumps are positive displacement pump components for use with the Graco and meter, mix, and dispense systems and are ideal for two-component sealant and adhesives requiring precision ratio, flow, and volume controls.

• Severe Duty coatings and 1/2 inch (1.27 cm) checks easily manage material wear from silicones, sealants, epoxies, and structural adhesives.
• Precision control eliminates pressure spikes and guarantees on ratio dispense.
• Pump seals are the only wear parts, which reduces maintenance downtime and repair costs.

• Model: Z-Pump
• Series: S4

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Industrial

• Ball Check Size (in): 1/2
• Ball Material: Silicon Nitride

• Coating Type: Severe Duty

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 1.905
• Fluid Inlet Size (in): 3/4
• Fluid Inlet Thread Gender: Female
• Fluid Inlet Thread Type: NPT

• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: SAE

• For Use With: EFR, HFR

• Maximum Flow Rate (GPM): 0.32

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 20

• Maximum Pump Speed (CPM): 60

• Maximum Viscosity (cP): 3000000

GG L086S1

LOWER, CHEMICAL, 86, SST, UCUP

Graco L086S1 Z-Pump, 86 cc, Severe Duty, S1

Z-Pumps are positive displacement pump components for use with the Graco meter, mix, and dispense systems and are ideal for two-component sealant and adhesives requiring precision ratio, flow, and volume controls.

• Severe Duty coatings and 1 inch (2.54 cm) checks easily manage material wear from silicones, sealants, epoxies, foam, and structural adhesives.
• Precision control eliminates pressure spikes and guarantees on ratio dispense.
• Pump seals are the only wear parts, which reduces maintenance downtime and repair costs.

• Model: Z-Pump
• Series: S1

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Industrial

• Ball Check Size (in): 1
• Ball Material: Silicon Nitride

• Coating Type: Severe Duty

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 1.905
• Fluid Inlet Size (in): 3/4
• Fluid Inlet Thread Gender: Female
• Fluid Inlet Thread Type: NPT

• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: SAE

• For Use With: HFR

• Maximum Flow Rate (GPM): 1.36

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 86

• Maximum Pump Speed (CPM): 60

• Maximum Viscosity (cP): 3000000

GG L040S1

LOWER, CHEMICAL, 40, SST, UCUP

Graco L040S1 Z-Pump, 40 cc, Severe Duty, S1

Z-Pumps are positive displacement pump components for use with the Graco meter, mix, and dispense systems and are ideal for two-component sealant and adhesives requiring precision ratio, flow, and volume controls.

• Severe Duty coatings and 1 inch (2.54 cm) checks easily manage material wear from silicones, sealants, epoxies, foam, and structural adhesives.
• Precision control eliminates pressure spikes and guarantees on ratio dispense.
• Pump seals are the only wear parts, which reduces maintenance downtime and repair costs.

• Model: Z-Pump
• Series: S1

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Industrial

• Ball Check Size (in): 1
• Ball Material: Silicon Nitride

• Coating Type: Severe Duty

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 1.905
• Fluid Inlet Size (in): 3/4
• Fluid Inlet Thread Gender: Female
• Fluid Inlet Thread Type: NPT

• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: SAE

• For Use With: HFR

• Maximum Flow Rate (GPM): 0.63

• Maximum Operating Temperature (°F): 180
• Maximum Output (cm³): 40

• Maximum Pump Speed (CPM): 60

• Maximum Viscosity (cP): 3000000

GG L010S4

LOWER, CHEMICAL, 010, SST, UCUP

Graco L010S4 Z-Pump, 10 cc, Severe Duty, S4

Z-Pumps are positive displacement pump components for use with the Graco and meter, mix, and dispense systems and are ideal for two-component sealant and adhesives requiring precision ratio, flow, and volume controls.

• Severe Duty coatings and 1/2 inch (1.27 cm) checks easily manage material wear from silicones, sealants, epoxies, and structural adhesives.
• Precision control eliminates pressure spikes and guarantees on ratio dispense.
• Pump seals are the only wear parts, which reduces maintenance downtime and repair costs.

• Model: Z-Pump
• Series: S4

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Industrial

• Ball Check Size (in): 1/2
• Ball Material: Silicon Nitride

• Coating Type: Severe Duty

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 1.905
• Fluid Inlet Size (in): 3/4
• Fluid Inlet Thread Gender: Female
• Fluid Inlet Thread Type: NPT

• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: SAE

• For Use With: EFR, HFR

• Maximum Flow Rate (GPM): 0.16

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 10

• Maximum Pump Speed (CPM): 60

• Maximum Viscosity (cP): 3000000

GG L005S1

LOWER, CHEMICAL, 5, SST, UCUP

Graco L005S1 Z-Pump, 5 cc, Severe Duty, S1

Z-Pumps are positive displacement pump components for use with the Graco meter, mix, and dispense systems and are ideal for two-component sealant and adhesives requiring precision ratio, flow, and volume controls.

• Severe Duty coatings and 1 inch (2.54 cm) checks easily manage material wear from silicones, sealants, epoxies, foam, and structural adhesives.
• Precision control eliminates pressure spikes and guarantees on ratio dispense.
• Pump seals are the only wear parts, which reduces maintenance downtime and repair costs.

• Model: Z-Pump
• Series: S1

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Industrial

• Ball Check Size (in): 1
• Ball Material: Silicon Nitride

• Coating Type: Severe Duty

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 1.905
• Fluid Inlet Size (in): 3/4
• Fluid Inlet Thread Gender: Female
• Fluid Inlet Thread Type: NPT

• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: SAE

• For Use With: HFR

• Maximum Flow Rate (GPM): 0.08

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 5

• Maximum Pump Speed (CPM): 60

• Maximum Viscosity (cP): 3000000

GG JS40M8

HIGH-FLO PUMP, 2200/1000, LOW DT, SLD, TRI

Graco JS40M8 High-Flo 4-Ball Pump, SST, 4:1, Low Noise Exhaust, DataTrak, Sealed SST Lower, Tri-Clamp Fittings, Ultralife Rod/Cylinder

Pneumatic High-Flo 4-ball piston pumps provide high output per cycle to reduce pump wear and maintenance. Ideal for low pressure, high flow applications and inherently safe for hazardous locations.

• Slow-moving reciprocating motion does not damage paint like other rotary pumping technologies
• Completely sealed fluid section can be used almost anywhere, including catalyst and moisture sensitive materials
• Ultralife Series ceramic coating holds up to the harshest materials, including waterborne paints
• Rugged body armor, won't rust or dent
• DataTrak tracks material usage, monitors and protects your pump

• Model: High-Flo
• Series: 4-Ball

• Application: Circulation

• Compatible Material: Waterborne, Solvent borne, High Solids, Xirallic, Metallics, Topcoats, Stains, Varnish, CARC

• Fluid Outlet Size (in): 1-1/2
• Fluid Outlet Size (mm): 38.1
• Fluid Section Type: Sealed

• Includes: Stainless Steel Pump, Low Noise Exhaust, DataTrak Monitor, Tri-Clamp Fittings, Ultralife Rod, Ultralife Cylinder

• Material: Stainless Steel

• Maximum Air Inlet Pressure (bar): 6.9
• Maximum Air Inlet Pressure (kPa): 690
• Maximum Air Inlet Pressure (psi): 100

• Maximum Continuous Cycle Rate (CPM): 20

• Maximum Flow Rate (GPM): 16.9
• Maximum Flow Rate (L/min): 63.97

• Maximum Operating Temperature ( degree C): 66
• Maximum Operating Temperature ( degree F): 150

• Maximum Working Pressure (bar): 28
• Maximum Working Pressure (kPa): 2800
• Maximum Working Pressure (MPa): 2.8
• Maximum Working Pressure (psi): 400

• Motor Type: Low Noise NXT with DataTrak

• Portable: Non-Portable

• Pump Ratio: 4:1

GG HSHC5B

XD SERIES 30 REEL, 1/2 X 50, GREASE, BLUE

Graco HSHC5B XD30, Grease, 1/2 in. (13 mm) Inlet, 1/2 in. X 50 ft. (13 mm X 15 m) Hose, NPT, Truck/Bench Mount, Metallic Blue

Graco's XD30 Series Hose Reels are used in applications requiring longer-range dispense and higher capacity than the standard XD10 and XD20 Series. The Compact pedestal and spool fits into tight spaces and can accommodate 30-75 foot (9.1-22.8 meters) hose capacity for a wide variety of applications. Typical fluids handled include: Petroleum- and synthetic-based oils, diesel fuel, air, water, antifreeze, windshield washer fluid, pressure wash, waste oil and diesel exhaust fluid (DEF).

• Spring Adjustment - Increase or decrease spring tension while reel is pressurized with fluid
• Full-Flow Swivel - Maximize material flow with minimal pressure drop for faster fills to get more vehicles through your shop
• Optional Adjustable Arm - Easily change the arm position for your application, order with arm (HS models) or without (HN models)
• Large Hose Capacity with Small Profile - Compact pedestal and spool fits into tight spaces and can accommodate 30-75 foot (91-228 meters) hose capacity for a wide variety of applications

• Model: XD
• Series: 30

• Application: Grease

• Color: Metallic Blue

• Dry Weight (lb): 98

• Frame Type: Dual Pedestal

• Hose Inside Diameter (in): 1/2
• Hose Inside Diameter (mm): 12.7
• Hose Length (ft): 50
• Hose Length (m): 15

• Hose Reel Type: Reel with Hose
• Includes Hose: Yes
• Inlet Size (in): 1/2
• Inlet Size (mm): 12.7

• Inlet Thread Type: NPSM

• Maximum Working Pressure (psi): 5000

• Mount Location: Truck Mount, Bench Mount

• Outlet Size (in): 1/2
• Outlet Size (mm): 12.7

• Overall Height (in): 27.6
• Overall Height (mm): 701
• Overall Length (in): 25.96
• Overall Length (mm): 659
• Overall Width (in): 9.0
• Overall Width (mm): 229

• Recommended Environment: Indoor, Outdoor
• Recommended Fluid Type: Grease

GG L85T12

PRO XP GUN, ES, 85KV, 1.2

Graco L85T12 Pro Xp85 Air Spray Manual Electrostatic General Gun Model, 85 kV, 0.047 in (1.2 mm) nozzle, standard display, standard coatings

Available in 85 kV, this general model is the smallest profile gun with an internal power supply on the market. The 1.2 mm nozzle is for lower fluid flow.

• Painters experience less muscle strain and fatigue when spraying with the ergonomic, lightweight electrostatic gun model.
• Electrostatic air spray gun meets strict requirements for spray pattern, mechanical and electrical performance.
• Durable, easy-to-repair components are backed by a three-year warranty and A+ Service.

• Model: Pro Xp
• Series: 85
• Product Series: A

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Gender: Male
• Air Inlet Thread Type: NPSM

• Application: Electrostatic, Standard
• Applicator Type: Manual

• Coating Type: Standard, Specialty

• Compatible Paint Type: Automotive, Base Coat, Clear Coat, Enamels, High Solids, Metallics, Plural Component Materials, Primers, Solvent borne, Urethanes

• Display Type: Standard

• Fluid Inlet Size (in): 3/8
• Fluid Inlet Thread Gender: Male
• Fluid Inlet Thread Type: NPSM

• Gun Activation: Manual
• Gun Type: Electrostatic
• Gun Weight (g): 676
• Gun Weight (kg): 0.675
• Gun Weight (lb): 1.49
• Gun Weight (oz): 23.81

• Includes: Air Cap, Nozzle, Tool Kit, Gun Cover, Exhaust Tube

• Maximum Fluid Pressure (bar): 7.0
• Maximum Fluid Pressure (kg/cm 2): 7.14
• Maximum Fluid Pressure (kPa): 700
• Maximum Fluid Pressure (MPa): 0.7
• Maximum Fluid Pressure (psi): 100
• Maximum Fluid Temperature (degree C): 48
• Maximum Fluid Temperature ( degree F): 120

• Maximum Fluid Pressure (bar): 7.0
• Maximum Fluid Pressure (kg/cm 2): 7.14
• Maximum Fluid Pressure (kPa): 700
• Maximum Fluid Pressure (MPa): 0.7
• Maximum Fluid Pressure (psi): 100
• Maximum Fluid Temperature ( degree C): 48
• Maximum Fluid Temperature (degree F): 120

• Maximum Paint Resistivity (megohm/cm): Infinity

• Minimum Paint Resistivity (megohm/cm): 25

• Nozzle Size (cm): 0.12
• Nozzle Size (in): 0.047
• Nozzle Size (mm): 1.2

• Overall Length (cm): 26.67
• Overall Length (in): 10.5
• Overall Length (mm): 266.7

GG LC0005

GG LB150A

GG LC1800

GG LC0885

GG LC0809

GG LC0094

GG LC0882

GG LC0805

PR70 HOSE, ASSY, FITTINGS, 1/4X120, SS

Graco LC0805 1/4 in x 120 in PR70 Stainless Steel Hose Package

• Inside Diameter (cm): 0.635
• Inside Diameter (in): 1/4
• Inside Diameter (mm): 6.35

• Material: Stainless Steel

• Maximum Working Pressure (bar): 210
• Maximum Working Pressure (kPa): 2100
• Maximum Working Pressure (MPa): 21
• Maximum Working Pressure (psi): 3000