Sealant and Adhesives

GG 24X167

LSR F4-55 SYSTEM, 55GAL/55GAL, CASTERS

1:1 Ratio 55 gal (200 liter) F4 Fluid Automation System with Casters

In the manufacturing of liquid silicone rubber products, precision is paramount. Material waste is an expensive problem and substandard products are an intolerable failure. Minimize both with the Graco Fluid Automation F4-55.

Ideal for manufacturing in the following industries: medical, infant care, consumer products, automotive, industrial parts, wearables.

Precise ratio control, minimal material waste

• The F4-55 system takes the ability to meter material flow to an almost microscopic level. Its helical gear uses multiple gear teeth to measure flow in very small increments. The increased number of measurements offers more assurance the machine remains on-ratio.
• The result: More precise mixing, a better end product and less wasted material.

Easier operation with Graco Control Architecture

• The Graco Fluid Automation F4-55 system features intuitive user interfaces based on the Graco Control Architecture (GCA), a modular system of processing and control components. GCA makes maintenance and service easy, thanks to built-in troubleshooting tools

Better Color Control

• Mix two additive streams at ratios ranging from 0.5 to 6%

Easy Set-up and Operation

• Proprietary Graco Control Architecture (GCA) is user friendly, providing easier operation and troubleshooting

Maintains Material Integrity

• Stainless steel components meet the standard for clean room applications to prevent contamination, and cure inhibition and discoloration of material

Cleanroom Convenience

• A smaller footprint and casters (optional on F4-55) allow for system movement and maintenance

GG 24X169

LSR F4-55 SYSTEM, 55GAL/55GAL

1:1 Ratio 55 gal (200 liter) F4-55 Fluid Automation System

In the manufacturing of liquid silicone rubber products, precision is paramount. Material waste is an expensive problem and substandard products are an intolerable failure. Minimize both with the Graco Fluid Automation F4-55.

Ideal for manufacturing in the following industries: medical, infant care, consumer products, automotive, industrial parts, wearables.

Precise ratio control, minimal material waste

• The F4-55 system takes the ability to meter material flow to an almost microscopic level. Its helical gear uses multiple gear teeth to measure flow in very small increments. The increased number of measurements offers more assurance the machine remains on-ratio.
• The result: More precise mixing, a better end product and less wasted material.

Easier operation with Graco Control Architecture

• The Graco Fluid Automation F4-55 system features intuitive user interfaces based on the Graco Control Architecture (GCA), a modular system of processing and control components. GCA makes maintenance and service easy, thanks to built-in troubleshooting tools

Better Color Control

• Mix two additive streams at ratios ranging from 0.5 to 6%

Easy Set-up and Operation

• Proprietary Graco Control Architecture (GCA) is user friendly, providing easier operation and troubleshooting

Maintains Material Integrity

• Stainless steel components meet the standard for clean room applications to prevent contamination, and cure inhibition and discoloration of material

Cleanroom Convenience

• A smaller footprint and casters (optional on F4-55) allow for system movement and maintenance

GG 255442

MD2 VALVE, ASSY, 1:1, HS, GUN, AIR

1:1 Ratio, Hard Seat, Air-Actuated Gun, Non-adjustable Snuff-back, Manual Handle Manual gun option for mixing dispense (MD) valve for 2 component materials supports minimizing maintenance while maximizing production. Static valve reliably dispenses and mixes a wide range of 2 component sealants and adhesives. 1:1 ratio nose handles a wide range of material. Carbide hard seats and hardened needles are good for abrasive material and stall against pressure applications. Hand held valve with internal air trigger controls the air piston that operates the MD2 valve. A pilot port can be used to control a pump motor. Non-adjustable snuff-back control keeps shut-off performance consistent for a clean bead dispense. Maximum flow rate is 25 to 30 cc/s, depending on material viscosity. Snuff-back control prevents dripping as it brings material back into the valve until next dispense. Hand held pneumatic handle eases manual dispense.

GG 255446

MD2 VALVE, ASSY, 10:1, HS, GUN, ELEC

10:1 Wide Ratio, Hard Seat, Electric Actuated, Non-adjustable Snuff-back, Manual Handle Manual gun option for mixing dispense (MD) valve for 2 component materials supports minimizing maintenance while maximizing production. Static valve reliably dispenses and mixes a wide range of 2 component sealants and adhesives. Wide ratio valve with center injection tip works well when the low volume material has a much lower viscosity than the high volume material. Frequent cleaning intervals may be required to maintain the tip. Carbide hard seats and hardened needles are good for abrasive material and stall against pressure applications. Hand held valve with electric switch signals the controller to open and close the ports on the MD2 valve. The process uses a remote four-way air control (not included; must be ordered separately). Non-adjustable snuff-back control keeps shut-off performance consistent for a clean bead dispense. Maximum flow rate is 25 to 30 cc/s, depending on material viscosity. Snuff-back control prevents dripping as it brings material back into the valve until next dispense. Hand held electric handle eases manual dispense.

GG 255901

MD2 VALVE, DISPENSE, 1:1, ELITE, SNUFF

MD2 Valve, 1:1 Ratio, Elite Hard Seat, Non-adjustable Snuff-back Mixing dispense (MD) valve for 2 component materials minimizes maintenance while maximizing production. Static valve with Elite construction reliably dispenses highly abrasive thermal interface materials (TIMs), silicones, urethanes, and epoxies. 1:1 ratio nose handles a wide range of material. Hard seats with Elite construction withstand highly abrasive material at least 10 times longer than standard construction. (Data verified in Graco test environment.) Snuff-back control prevents dripping as it brings material back into the valve until next dispense. Non-adjustable snuff-back control keeps shut-off performance consistent for a clean bead dispense. Maximum flow rate is 25 to 30 cc/s, depending on material viscosity. No unique tools are required for maintenance or repair. Grease isolation chamber protects moisture sensitive materials and has accessible grease fittings for easy maintenance No unique tools required

GG 25C861

LSR SYSTEM, 1:1 EXTRUDER, 5/5GAL

1:1 Extruder, Stainless Steel, for Liquid Silicone Rubber

GG TK1000

PROMIX 3KS PROPORTIONER

ProMix 3KS Proportioner, G3000 Meter, Single Color ProMix 3KS offers precision mixing of a broad range of three component materials, even tough acid catalysts. It accurately reduces your material to the correct spray viscosity as conditions change with the highest degree of ratio assurance for superior quality on both manual and automatic applications. Efficient tracking and reporting along with effective color changes reduces wasted material. Purchase with a ProMix 2KS system or upgrade an existing 2KS system Advanced web interface provides consolidated system management and reporting Intrinsically safe fluid panels easily integrate into hazardous areas Simple programming allows fast set up and efficient process control

GG TK4000

PROMIX 3KS PROPORTIONER

Graco TK4000 ProMix 3KS Proportioner, S3000 Meter, Single Color

ProMix 3KS offers precision mixing of a broad range of three component materials, even tough acid catalysts. It accurately reduces your material to the correct spray viscosity as conditions change with the highest degree of ratio assurance for superior quality on both manual and automatic applications. Efficient tracking and reporting along with effective color changes reduces wasted material.

• Purchase with a ProMix 2KS system or upgrade an existing 2KS system
• Advanced web interface provides consolidated system management and reporting
• Intrinsically safe fluid panels easily integrate into hazardous areas

• Model: ProMix
• Series: 3KS

• Air Inlet Size (cm): 0.9525
• Air Inlet Size (in): 3/8
• Air Inlet Size (mm): 9.525
• Air Inlet Thread Gender: Female
• Air Inlet Thread Type: NPT

• Amperage (A): 2

• Component Type: Three Component

• Fluid Inlet Size (cm): 0.635
• Fluid Inlet Size (in): 1/4
• Fluid Inlet Size (mm): 6.35
• Fluid Inlet Thread Gender: Female
• Fluid Inlet Thread Type: NPT

• Fluid Outlet Size (in): 1/4
• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: NPT
• Flush Type: Air/Solvent

• Frequency (Hz): 50/60

• Gun Activation: Manual

• Material Type: Three Component

• Maximum Flow Rate (cc/min): 1890

• Maximum Flow Rate (GPM): 0.5
• Maximum Flow Rate (L/min): 1.89

• Maximum Fluid Viscosity (cP): 1000

• Maximum Fluid Viscosity (cP): 1000

• Maximum Mix Ratio: 50:1
• Maximum Number of Colors: Up to 25

• Maximum Operating Temperature (°C): 50
• Maximum Operating Temperature (°F): 122

• Maximum Working Pressure (bar): 158.6
• Maximum Working Pressure (kPa): 15860
• Maximum Working Pressure (MPa): 15.9
• Maximum Working Pressure (psi): 2300
• Measuring Type: Meter
• Meter Type: S3000

• Minimum Flow Rate (cc/min): 38
• Minimum Flow Rate (GPM): 0.01
• Minimum Flow Rate (L/min): 0.038

• Minimum Fluid Viscosity (cP): 0.5
• Minimum Mix Ratio: 0.1:1

• Mix Accuracy (%): 1

• Number of Catalysts: 4
• Number of Color Valves: No Valves
• Number of Colors: 1

• Number of Reducers: 4

• Number of Resin Colors: 1

• Power Source: Electric

• Proportioning Type: Manual Electronic, Automatic Electronic