Sealant and Adhesives

GG 01/1455/98

GG 15E684

GG 249571

REACTOR E-10 PROPORTIONER, CMPLT, 240V, 2X10A, HTD

Graco 249571 Reactor E-10 Heated Proportioner with (2) 10 A Circuits, 240 V

Gracos Reactor E-10 is a small, ready-to-use system that helps you get in and get smaller jobs done fast without sacrificing performance. The Reactor E-10 sprayers are ideal for plural-component spray, joint-fill jobs and touch-ups. With smart controls that are easy to setup and simple to operate, the E-10 is a natural complement to any proportioning equipment line-up.

• Small size
  

  Ideal for on-site portability and hard-to-reach areas

• Cost Savings
  

  One-person operation saves time and money

• Extent your spray business
  

  Use as an add-on to your existing spray business

• Material savings
  

  Saves 30% on material costs compared to disposable foam systems

• Electric power
  

  Low draw and plugs into standard outlets

• Single Knob Operation
  

  Intuitive start, stop and digital temperature display with single knob operation

• Easily balancing
  

  Pressure balance valves give you quick and easy balancing of system pressures

  Balanced proportioning eliminates pressure fluctuations to give you a consistent spray pattern

• Easy-to-service fluid section
  

  Reduces maintenance and increases productivity

• Electric motor
  

  Improves performance and reduces operating costs

• Spray on-ratio
  

  Self-contained translucent material tanks show you that you are spraying on-ratio

• Pre-heat material
  

  Heaters and hose give you up to 2000 watts to pre-heat circulating material

• Model: Reactor
• Series: E-10

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35

• Air Outlet Size (cm): 0.635
• Air Outlet Size (in): 1/4
• Air Outlet Size (mm): 6.35
• Air Outlet Thread Type: NPSM

• Amperage (A): 10
• Application: Spray Foam
• Applicator Type: Manual

• Compatible Material: Plural Components

• Component Type: Two Component

• Flush Type: Solvent

• Frequency (Hz): 50/60

• Gun Type: No Gun

• Hose Package: No Hose

• Material Application: Polyurethane Foam

• Maximum Flow Rate (kg/min): 5.44
• Maximum Flow Rate (lb/min): 12

• Maximum Fluid Temperature ( degree C): 71
• Maximum Fluid Temperature ( degree F): 160

• Maximum Fluid Temperature ( degree C): 71
• Maximum Fluid Temperature ( degree F): 160

• Maximum Hose Length (ft): 35
• Maximum Hose Length (m): 94.5

• Maximum Mix Ratio: 1:1

• Maximum Working Pressure (bar): 138
• Maximum Working Pressure (kPa): 13800
• Maximum Working Pressure (MPa): 13.8
• Maximum Working Pressure (psi): 2000

• Overall Depth (cm): 76.2
• Overall Depth (in): 30
• Overall Depth (mm): 762

• Overall Height (cm): 111.8
• Overall Height (in): 44
• Overall Height (mm): 1118
• Overall Width (cm): 67.3
• Overall Width (in): 26.5
• Overall Width (mm): 673

• Power Rating (HP): 5

GG 24R137

GG 25C861

LSR SYSTEM, 1:1 EXTRUDER, 5/5GAL

Graco 25C861 1:1 Extruder, Stainless Steel, for Liquid Silicone Rubber

Application:

• Reduces material costs
• Saves money by using less clean-up solvent
• Provides consistent material quality

• Model: LSR

• Air Inlet Size (in): 1/2
• Air Inlet Thread Gender: Female
• Air Inlet Thread Type: NPT

• Maximum Working Pressure (bar): 3000
• Maximum Working Pressure (kPa): 30000
• Maximum Working Pressure (psi): 3000

• Overall Depth (cm): 64.0080
• Overall Depth (in): 25.2
• Overall Depth (mm): 640

• Overall Height (cm): 173.7360
• Overall Height (in): 68.4
• Overall Height (mm): 1737
• Overall Width (cm): 106.6800
• Overall Width (in): 42
• Overall Width (mm): 1067

GG TOFC-200-A-NNN-5-M-1-P-N

LC 1049135-1

LC 1049136

LC 1049137

LC 1153491

LC 1153492

LC 1153498

LC 1153502

LC 1275665

LC 1335041

LC 135561

LC 1390321

LC 1401792

LC 142641

LC 209688

LC 21348

LC 2265279

LC 231232

LC 2759219

LC 376747