GRACO INC. S10595
REACTOR E-10 PROPORTIONER, CMPLT, 240V, 1X16A, HTD
GG 249572
REACTOR E-10 PROPORTIONER, CMPLT, 240V, 1X16A, HTD
Graco 249572 Reactor E-10 Heated Proportioner with 20 A Circuit, 240 V
Graco&prime, s Reactor E-10 is a small, ready-to-use system that helps you get in and get smaller jobs done fast without sacrificing performance. The Reactor E-10 sprayers are ideal for plural-component spray, joint-fill jobs and touch-ups. With smart controls that are easy to setup and simple to operate, the E-10 is a natural complement to any proportioning equipment line-up.
- Small size
Ideal for on-site portability and hard-to-reach areas
- Cost Savings
One-person operation saves time and money
- Extent your spray business
Use as an add-on to your existing spray business
- Material savings
Saves 30% on material costs compared to disposable foam systems
- Electric power
Low draw and plugs into standard outlets
- Single Knob Operation
Intuitive start, stop and digital temperature display with single knob operation
- Easily balancing
Pressure balance valves give you quick and easy balancing of system pressures
Balanced proportioning eliminates pressure fluctuations to give you a consistent spray pattern
- Easy-to-service fluid section
Reduces maintenance and increases productivity
- Electric motor
Improves performance and reduces operating costs
- Spray on-ratio
Self-contained translucent material tanks show you that you are spraying on-ratio
- Pre-heat material
Heaters and hose give you up to 2000 watts to pre-heat circulating material
- Model: Reactor
- Series: E-10
- Air Inlet Size (cm): 0.635
- Air Inlet Size (in): 1/4
- Air Inlet Size (mm): 6.35
- Air Outlet Size (cm): 0.635
- Air Outlet Size (in): 1/4
- Air Outlet Size (mm): 6.35
- Air Outlet Thread Type: NPSM
- Amperage (A): 20
- Application: Spray Foam
- Applicator Type: Manual
- Compatible Material: Plural Components
- Component Type: Two Component
- Flush Type: Solvent
- Frequency (Hz): 50/60
- Gun Type: No Gun
- Hose Package: No Hose
- Material Application: Polyurethane Foam
- Maximum Flow Rate (kg/min): 5.44
- Maximum Flow Rate (lb/min): 12
- Maximum Fluid Temperature (°C): 71
- Maximum Fluid Temperature (°F): 160
- Maximum Fluid Temperature (°C): 71
- Maximum Fluid Temperature (°F): 160
- Maximum Hose Length (ft): 35
- Maximum Hose Length (m): 94.5
- Maximum Mix Ratio: 1:1
- Maximum Working Pressure (bar): 138
- Maximum Working Pressure (kPa): 1380
Diffuser, Assembly, Rac
GG 249877
DIFFUSER, ASSY,RAC
Graco 249877 Diffuser Assembly for Flat Tip to RAC Tip Air Cap Conversion Kit
- Compatible Material: Sealants, Adhesives
CHANNEL, MOUNTING, DUAL ARM 1 REEL
GG 24A219
CHANNEL, MOUNTING, DUAL ARM 1 REEL
Graco 24A219 XD Series Open Reel Mounting Channel - Accommodates 1 Reel
- Number of Pieces: 9
FUSION AP GUN, AF5252 FTM979
GG 249526
FUSION AP GUN, AF5252 FTM979
Graco 249526 Round Fusion Air-Purge Stud Wall Gun with 0.070 Mix Chamber
With long-life mix chamber and durable side seals, Fusion guns are designed to reduce maintenance and downtime, and provide a better mix.
Application: For high output spray polyurethane foam and polyurea applications.- Easy air-blast tip cleaning reduces build-up and tip clogging.
- Long-lasting side seals means less downtime for maintenance
- Quick-release fluid housing - lets you easily change the mix chambers without tools
- Ergonomic handle
- Model: Fusion AP
- Series: Specialty
- Compatible Material: Adhesives, Polyurethane, Polyurea, Polyurethane Coating, Spray Polyurethane Foam
- Fluid Orifice Size (cm): 0.132
- Fluid Orifice Size (in): 0.052
- Fluid Orifice Size (mm): 1.32
- Gun Type: Air Purge Gun
- Maximum Air Inlet Pressure (bar): 9
- Maximum Air Inlet Pressure (kPa): 900
- Maximum Air Inlet Pressure (MPa): 0.9
- Maximum Air Inlet Pressure (psi): 130
- Maximum Air Pressure (bar): 9
- Maximum Air Pressure (kPa): 900
- Maximum Air Pressure (MPa): 0.9
- Maximum Air Pressure (psi): 130
- Maximum Flow Rate @ PSI (lb/min): 50
- Maximum Fluid Pressure (bar): 241
- Maximum Fluid Pressure (kPa): 24100
- Maximum Fluid Pressure (MPa): 24.1
- Maximum Fluid Pressure (psi): 3500
- Maximum Fluid Pressure (bar): 241
- Maximum Fluid Pressure (kPa): 24100
- Maximum Fluid Pressure (MPa): 24.1
- Maximum Fluid Pressure (psi): 3500
- Minimum Air Inlet Pressure (bar): 5.5
- Minimum Air Inlet Pressure (kPa): 550
- Minimum Air Inlet Pressure (MPa): 0.55
- Minimum Air Inlet Pressure (psi): 80
- Mix Chamber: 04 (.070)
- Pattern Size (in): 22 in @ 24 in from target
DURA-FLO 1800 PUMP, RECIP, DISPL (18 SST)
GG 249992
DURA-FLO 1800 PUMP, RECIP, DISPL (18 SST)
Stainless Steel 18 cm Displacement Pump
KIT, ACCESSORY
GG 24A217
KIT, ACCESSORY
Graco 24A217 SD 10 Oil Reel Enclosure - White
- Number of Pieces: 22
Kit, Repair, Vee, 25Cc
GG 24A251
KIT, REPAIR, VEE, 25CC
Graco 24A251 Standard Seal Repair Kit for Merkur LW025A
Kit, Repair, Vee, 50Cc
GG 24A252
KIT, REPAIR,VEE, 50CC
Graco 24A252 Standard Seal Repair Kit for Merkur LW050A
CHANNEL, MOUNTING, DUAL ARM 2 REEL
GG 24A220
CHANNEL, MOUNTING, DUAL ARM 2 REEL
Graco 24A220 Open Reel Mounting Channel (Accommodates 2 Reels)
- Number of Pieces: 17
Applicator, L-Rim:10/14, Mixhead, w/Calib
GG 24A085
APPLICATOR,L-RIM:10/14,MIXHEAD,W/CALIB
GH SPRAYER, 833, COMPLETE
GG 249617
GH SPRAYER, 833, COMPLETE
Graco 249617 GH 833 Gas Hydraulic Sprayer, Complete
The GH 833 is the preferred choice for high production professional contractors who spray the wide range of materials. This jobsite-proven workhorse is the answer when you demand ruggedness, performance and value.
- Honda® Engine
390 cc (13 HP) engine with integrated fuel tank to deliver maximum performance
Contractor preferred engine with Oil Alert
- Heavy-Duty Hydraulic System
Faster, more responsive changeover
O-ring sealed to eliminate leaks
High-precision pressure control
No hydraulic reset button needed
Durable hydraulic lines for long life
- Heavy-Duty Cooling System
Large 4 gallon hydraulic reservoir
Return line hydraulic filter extends life
No special hydraulic fluid needed
Proven cooler and blower system
Easy to use drain plug
- MaxLife Endurance Pump
Proven design and performance
Only 16 cycles per gallon (4.2 cycles per liter)
Exclusive MaxLife rod and sleeve delivers unmatched durability and life – Graco’s best
Exclusive QuikChange Pump System and QuikAccess Intake Valve eliminates downtime
- Flow-Through Filter System
Inside/out design eliminates clogged filters
Eliminates tip clogs
- Ready-To-Spray Complete System
Configured with 50 feet of pressure-rated hose, gun, tips, and all the fittings you will need
- Model: GH
- Series: 833
- Compatible Material: Acrylics, Block Filler, Coal Tar, Contact Cement, Elastomerics, Enamel, Epoxies, Fibered Aluminum Emulsion, Fibered Asphalt Emulsion, Mastics, Non-Fibered Aluminum Emulsion, Non-Fibered Asphalt Emulsion, Paint, Polyester, Polyurethane, Primer, Texture Mud, Waterproofing
- Compatible Replacement Pump: 287834
- Control Type: N/A
- Engine Brand: Honda
- Engine Size (HP): 13
- Fluid Inlet Size (in): 1-1/2 to 11-1/2
- Fluid Inlet Thread Type: MNPT
- Fluid Outlet Size (in): 1 to 11-1/2
- Fluid Outlet Thread Type: FNPT
- Frame Configuration: Cart
- Includes: Silver Plus Gun, RAC X 517 Spray Tip, RAC X 655 Spray Tip, RAC X Guard, 3/8 in x 50 ft BlueMax II HP Airless Hose, 1/4 in x 3 ft BlueMax II HP Airless Whip Hose
- Material Application: Paints, Primers
- Maximum Flow Rate (GPM): 4.0
- Maximum Flow Rate (L/min): 15.1
- Maximum Hose Length (ft): 50
- Maximum Hose Length (m): 15
- Maximum Sound Pressure Level (dB(A)): 91
- Maximum Tip Size (in): 0.065
- Maximum Tip Size Gun 2 (in): 0.046
- Maximum Tip Size Gun 3 (in): 0.037
- Maximum Tip Size Gun 4 (in): 0.032
- Maximum Tip Size Gun 5 (in): 0.029
- Maximum Tip Size Gun 6 (in): 0.026
- Maximum Working Pressure (bar): 275.8
- Maximum Working Pressure (kPa): 27580
- Maximum Working Pressure (MPa): 27.6
- Maximum Working Pressure (psi): 4000
- M
Control, Flow, Regulator
GG 249849
CONTROL, FLOW, REGULATOR
Graco 249849 Flow Control Module with Integrated Air-Operated Fluid Regulator
- Compatible Material: Solventborne
REACTOR E-10 PROPORTIONER, CMPLT, 240V, 2X10A, HTD
GG 249571
REACTOR E-10 PROPORTIONER, CMPLT, 240V, 2X10A, HTD
Graco 249571 Reactor E-10 Heated Proportioner with (2) 10 A Circuits, 240 V
Graco&prime, s Reactor E-10 is a small, ready-to-use system that helps you get in and get smaller jobs done fast without sacrificing performance. The Reactor E-10 sprayers are ideal for plural-component spray, joint-fill jobs and touch-ups. With smart controls that are easy to setup and simple to operate, the E-10 is a natural complement to any proportioning equipment line-up.
- Small size
Ideal for on-site portability and hard-to-reach areas
- Cost Savings
One-person operation saves time and money
- Extent your spray business
Use as an add-on to your existing spray business
- Material savings
Saves 30% on material costs compared to disposable foam systems
- Electric power
Low draw and plugs into standard outlets
- Single Knob Operation
Intuitive start, stop and digital temperature display with single knob operation
- Easily balancing
Pressure balance valves give you quick and easy balancing of system pressures
Balanced proportioning eliminates pressure fluctuations to give you a consistent spray pattern
- Easy-to-service fluid section
Reduces maintenance and increases productivity
- Electric motor
Improves performance and reduces operating costs
- Spray on-ratio
Self-contained translucent material tanks show you that you are spraying on-ratio
- Pre-heat material
Heaters and hose give you up to 2000 watts to pre-heat circulating material
- Model: Reactor
- Series: E-10
- Air Inlet Size (cm): 0.635
- Air Inlet Size (in): 1/4
- Air Inlet Size (mm): 6.35
- Air Outlet Size (cm): 0.635
- Air Outlet Size (in): 1/4
- Air Outlet Size (mm): 6.35
- Air Outlet Thread Type: NPSM
- Amperage (A): 10
- Application: Spray Foam
- Applicator Type: Manual
- Compatible Material: Plural Components
- Component Type: Two Component
- Flush Type: Solvent
- Frequency (Hz): 50/60
- Gun Type: No Gun
- Hose Package: No Hose
- Material Application: Polyurethane Foam
- Maximum Flow Rate (kg/min): 5.44
- Maximum Flow Rate (lb/min): 12
- Maximum Fluid Temperature (°C): 71
- Maximum Fluid Temperature (°F): 160
- Maximum Fluid Temperature (°C): 71
- Maximum Fluid Temperature (°F): 160
- Maximum Hose Length (ft): 35
- Maximum Hose Length (m): 94.5
- Maximum Mix Ratio: 1:1
- Maximum Working Pressure (bar): 138
- Maximum Working Pressure (kPa):
Kit, Repair, Shaft And Bearing
GG 24A155
KIT,REPAIR,SHAFT AND BEARING
Graco 24A155 Shaft and Bearing Repair Kit- for Triton 308 Diaphragm Pumps
Kit, Repair, Vee, 75Cc
GG 24A253
KIT, REPAIR,VEE, 75CC
Graco 24A253 Standard Seal Repair Kit for Merkur LW075A
Kit, Repair, Vee, 100Cc
GG 24A254
KIT, REPAIR,VEE, 100CC
Graco 24A254 Standard Seal Repair Kit for Merkur LW100A
Kit, Repair, Vee, 125Cc
GG 24A255
KIT, REPAIR,VEE, 125CC
Graco 24A255 Standard Seal Repair Kit for Merkur LW125A
Kit, Repair, Vee, 150Cc
GG 24A256
KIT, REPAIR,VEE, 150CC
Graco 24A256 Standard Seal Repair Kit for Merkur LW150A
Kit, Seals, Air Valve, Medium
GG 24A536
KIT, SEALS, AIR VALVE, MEDIUM
Graco 24A536 Air Valve Seal Kit
Kit, Mech, Air Valve Medium
GG 24A538
KIT, MECH,AIR VALVE MEDIUM
Graco 24A538 Air Valve Repair Kit, for Graco Air Valve Models 24A352, 24A354, and 262608
Always install a new gasket when installing a new air valve
Kit, Seals, Motor 6.0
GG 24A547
KIT, SEALS, MOTOR 6.0
Graco 24A547 Air Motor Seal Kit
Kit, Sub Assembly, Piston, Motor, 3.5
GG 24A546
Kit, Sub Assembly, Piston, Motor, 3.5
Kit, Seals Motor, 7.5
GG 24A551
KIT, SEALS MOTOR, 7.5
Graco 24A551 Air Motor Seal Kit
Kit, Sub Assembly, Cover, Motor, 6.0
GG 24A549
Kit, Sub Assembly, Cover, Motor, 6.0
Datatrak Upgrade, 1200/1800Cc Air Motor
GG 24A576
Datatrak Upgrade, 1200/1800Cc Air Motor
Kit, Fluid Filter
GG 24A587
KIT, FLUID FILTER
Graco 24A587 Pump Outlet Fluid Filter, Stainless Steel, 60 mesh (250 micron), 5000 psi (350 bar)
Kit, Rod, Displ, Wetcup, 25Cc
GG 24A643
KIT, ROD,DISPL,WETCUP,25CC
Graco 24A643 Merkur Piston Rob Assembly Kit for Merkur Displacement Pump
RAC X FFLP TIP, SPRAY, (516)
GG FFLP516
RAC X FFLP TIP, SPRAY, (516)
Graco FFLP516 Fine Finish Low Pressure RAC X FF LP SwitchTip, 516
Spray at up to 50% lower pressure with the Reverse-A-Clean (RAC) 516 Fine Finish Low Pressure (FF LP) RAC X SwitchTip. This fine finish tip produces a 10 to 12 inch Fan pattern and has a 0.016 inch orifice, ideal for finishing materials. Reverse the SwitchTip to easily clear clogs.
Application: For fine finish applications- Less Prep & Cleanup Time
Less mess with less overspray
Put the paint where you want it
- Easiest Pattern Overlap
Softer spray fan pattern
Easy to apply any material to any surfance
Consistent blended finish quality
- Extended Life
Spraying at half pressure doubles tip life
Reduced sprayer maintenance – up to 2X life
- Best Tip on the Market
Works with any airless sprayer
Longest lasting Fan pattern
Highest quality finish with a consistent spray pattern
- Easy to Identify Tip Size
Large raised tip size numbers are always legible – even when covered with paint
- Superior Tip Design
Locking tab ensures tip stays securely in guard
Snaps tip in spray or reverse position
OneSeal tip gasket installs with no tools
Solvent seal available when using extremely hot solvents
- Model: RAC X
- Series: FF LP SwitchTip
- Compatible Material: Primer, Stains, Varnish, Water-Based Paint, Enamel, Latex, Solvent borne Paints
- For Use With: RAC X HandTite Tip Guard
- Material: Tungsten Carbide
- Maximum Fan Width (cm): 25
- Maximum Fan Width (in): 10
- Maximum Fan Width (mm): 305
- Maximum Flow Rate (GPM): 0.27
- Maximum Working Pressure (bar): 280
- Maximum Working Pressure (kPa): 28000
- Maximum Working Pressure (psi): 4050
- Minimum Fan Width (in): 10
- Minimum Fan Width (mm): 254
- Orifice Diameter (in): 0.016
- Pattern Size (in): 10 to 12
- Pattern Size (mm): 254 to 304.8
MERKUR SYSTEM, PUMP, 3:1, 125CC, CART, STD
GG G03C03
MERKUR SYSTEM, PUMP, 3:1, 125CC, CART, STD
Graco G03C03 3:1 Merkur Air Spray Package, 125cc, Cart, Pump/Gun Air Controls, Siphon Kit, Fluid Filter, No Applicator
Make the right choice for your finishing applications with Merkur Low Pressure Packages. The Merkur low-pressure piston pump comes with advanced air spray technology.
- The pump lower has the best solution for smooth, low pulsation operation.
- The air motor operates efficiently with low air consumption.
- Cart mount configuration makes fine finish spraying easy in different locations.
- Model: Merkur
- Fluid Inlet Size (cm): 2.54
- Fluid Inlet Size (in): 1
- Fluid Inlet Size (mm): 25.4
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 1.27
- Fluid Outlet Size (in): 1/2
- Fluid Outlet Size (mm): 12.7
- Fluid Outlet Thread Type: NPT
- Gun Included: 0
- Gun Model: No Applicator
- Gun Technology: Bare Package
- Gun Type: No Applicator
- Includes: Pump and Gun Air Controls, Siphon Kit, Fluid Filter
- Maximum Air Pressure (bar): 6.9
- Maximum Air Pressure (kPa): 690
- Maximum Air Pressure (psi): 100
- Maximum Flow Rate (GPM): 2
- Maximum Flow Rate (L/min): 7.5
- Maximum Operating Temperature (°C): 49
- Maximum Operating Temperature (°F): 120
- Maximum Working Pressure (bar): 8.3
- Maximum Working Pressure (MPa): 0.8
- Maximum Working Pressure (psi): 120
- Mount Type: Cart Mount
- Power Source: Air
- Pressure Type: Low Pressure
- Product Type: Bare Package
- Pump Ratio: 3:1
- Pump Type: Pneumatic Piston Pump
SANIFORCE AODD PUMP, 2150FG-PS01AS13SSPTPOPT21
GG FD3113
SANIFORCE AODD PUMP, 2150FG-PS01AS13SSPTPOPT21
Graco FD3113 SaniForce 2150 Diaphragm Pump for Barrel-to-Barrel Transfer and Pump-Over
Graco’s SaniForce 2150 air-operated double diaphragm sanitary pumps have one of the best, most durable, lube-free air valves in the industry. Ideal for applications requiring high flow rates and portability, Graco’s dependable diaphragm pumps offer a wide range of food-grade elastomers including Santoprene, PTFE and overmolded EPDM/PTFE.
- SaniForce 2150 Double Diaphragm Pump
- Patented, lube-free air valve
- PTFE/EPDM Overmolded Diaphragms
Overmolded diaphragm plate with PTFE on the fluid side and EPDM on the air side on Graco&prime, s PTFE/EPDM diaphragms so there&prime, s no place to harbor bacteria
Improve wear and diaphragm life with no exposed diaphragm plate on the fluid side
Longer diaphragm life in abrasive applications that still require PTFE
Available on the SaniForce 1040, 1590, 2150 and SaniForce HS 1590 and 3150
- Model: SaniForce
- Series: 2150
- Air Exhaust Port Size (in): 3/4
- Air Exhaust Port Thread Gender: Female
- Air Exhaust Port Thread Type: NPT
- Air Inlet Size (in): 1/2
- Air Inlet Thread Gender: Female
- Air Inlet Thread Type: NPT
- Application: Sanitary
- Ball Material: PTFE
- Center Section Material: Stainless Steel
- Compatible Material: Edible Oil, Food and Personal Care
- Connection Type: Tri-Clamp
- Diaphragm Compatible Material: PTFE
- Diaphragm Material: PTFE Overmold
- Fluid Inlet Size (cm): 6.35
- Fluid Inlet Size (in): 2
- Fluid Inlet Size (mm): 63.5
- Fluid Outlet Size (cm): 6.35
- Fluid Outlet Size (in): 2
- Fluid Outlet Size (mm): 63.5
- Fluid Section Material: 316L Stainless Steel
- For Use With: Food and Personal Care
- Manifold Configuration: End Port
- Manifold O-Ring Material: PTFE
- Material: Stainless Steel
- Maximum Air Consumption (SCFM): 175
- Maximum Air Pressure (bar): 8
- Maximum Air Pressure (kPa): 800
- Maximum Air Pressure (MPa): 0.8
- Maximum Air Pressure (psi): 120
- Maximum Cycle Rate (CPM): 165
- Maximum Flo
Three-way pilot valve for no-stick operation
Long-lasting 16 Series stainless steel rod design for long life and corrosion resistance
1040, 1590 and 2150 SaniForce pumps use common center sections
100% externally serviceable air valve
- PTFE/EPDM Overmolded Diaphragms
2-1/2 in (63.5 mm) Tri-clamp connection
Flow rates up to 150 gpm (567 lpm) (568 lpm)
Fluid pressure to 120 psi (8.4 bar, 0.84 MPa)
All fluid contact materials are FDA-Compliant and meet the United States Code of Federal Regulations (CFR) Title 21
High volume evacuation of liquid concentrates from holding vessels or repackaging of fluids from original container to smaller receptacles - up to 20,000 cps
Suitable to pump such products as: concentrated fruit juices, sauces, pastes, starches, wine, food-grade oil, jams and jellies
- Patented, lube-free air valve
MERKUR SYSTEM, PUMP, 3:1, 125CC, WALL, STD
GG G03W01
MERKUR SYSTEM, PUMP, 3:1, 125CC, WALL, STD
Graco G03W01 3:1 Merkur Air Spray Package, 125cc, Wall, Pump/Gun Air Controls, Siphon Kit, No Applicator
Make the right choice for your finishing applications with Merkur Low Pressure Packages. The Merkur low-pressure piston pump comes with advanced air spray technology.
- The pump lower has the best solution for smooth, low pulsation operation.
- The air motor operates efficiently with low air consumption.
- Wall mount configuration offers easy access to data monitoring and controls.
- Model: Merkur
- Fluid Inlet Size (cm): 2.54
- Fluid Inlet Size (in): 1
- Fluid Inlet Size (mm): 25.4
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 1.27
- Fluid Outlet Size (in): 1/2
- Fluid Outlet Size (mm): 12.7
- Fluid Outlet Thread Type: NPT
- Gun Included: 0
- Gun Model: No Applicator
- Gun Technology: Bare Package
- Gun Type: No Applicator
- Includes: Pump and Gun Air Controls, Siphon Kit
- Maximum Air Pressure (bar): 6.9
- Maximum Air Pressure (kPa): 690
- Maximum Air Pressure (psi): 100
- Maximum Flow Rate (GPM): 2
- Maximum Flow Rate (L/min): 7.5
- Maximum Operating Temperature (°C): 49
- Maximum Operating Temperature (°F): 120
- Maximum Working Pressure (bar): 8.3
- Maximum Working Pressure (MPa): 0.8
- Maximum Working Pressure (psi): 120
- Mount Type: Wall Mount
- Power Source: Air
- Pressure Type: Low Pressure
- Product Type: Bare Package
- Pump Ratio: 3:1
- Pump Type: Pneumatic Piston Pump
RAC X FFLP TIP, SPRAY, (514)
GG FFLP514
RAC X FFLP TIP, SPRAY, (514)
Fine Finish Low Pressure RAC X FF LP SwitchTip, 514 Spray at up to 50% lower pressure with the Reverse-A-Clean (RAC) 514 Fine Finish Low Pressure (FF LP) RAC X SwitchTip. This fine finish tip produces a 10 to 12 inch Fan pattern and has a 0.014 inch orifice, ideal for finishing materials. Reverse the SwitchTip to easily clear clogs. For fine finish applications Less Prep & Cleanup Time- Less mess with less overspray
- Put the paint where you want it
- Softer spray fan pattern
- Easy to apply any material to any surfance
- Consistent blended finish quality
- Spraying at half pressure doubles tip life
- Reduced sprayer maintenance – up to 2X life
- Exclusive internal tip geometry
- Reduces energy required to atomize paints, stains, and other materials
- Delivers a superior finish with less pressure
- Works with SmartControl on select Graco sprayers
- Works with any airless sprayer
- Longest lasting Fan pattern
- Highest quality finish with a consistent spray pattern
- Large raised tip size numbers are always legible – even when covered with paint
- Locking tab ensures tip stays securely in guard
- Snaps tip in spray or reverse position
- OneSeal tip gasket installs with no tools
- Solvent seal available when using extremely hot solvents
MERKUR BELLOWS SYSTEM, PUMP, 150CC, STD
GG G05B01
MERKUR BELLOWS SYSTEM, PUMP, 150CC, STD
Merkur Bellows 5:1 Ratio Pump Package with V-Packing Seal, Wall Mount, Fluid Filter Graco’s Merkur bellows piston pumps provide low maintenance with no seals exposed to the atmosphere. These pumps are designed to eliminate conventional throat seals, providing high reliability for moisture-sensitive materials. Highest technology air motor on the market Low air consumption for increased efficiency Simple air motor design and minimal parts reduces repair time Easy-to-flush design allows for fast color changes and reduced material waste 300 series stainless steel pump construction provides long-lasting durability
MERKUR SYSTEM PUMP 10:01 75CC WA STD
GG G10W01
MERKUR SYSTEM PUMP 10:01 75CC WA STD
Graco G10W01 10:1 Merkur Pump, 1.2 gpm (4.5 lpm) fluid flow, Wall Mount, Pump/Gun Air Controls
Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications.
- Proven to outperform and outlast other pumps in their class
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Model: Merkur
- Compatible Material: Waterborne, Solvent borne, High Solids, Single Components, Topcoats, Varnish, Lacquer, Acid Catalysts, Enamel, UV Coating
- Fluid Inlet Size (cm): 1.905
- Fluid Inlet Size (in): 3/4
- Fluid Inlet Size (mm): 19.05
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 0.9525
- Fluid Outlet Size (in): 3/8
- Fluid Outlet Size (mm): 9.525
- Fluid Outlet Thread Type: NPT
- Gun Included: 0
- Gun Model: No Applicator
- Gun Technology: Bare Package
- Gun Type: No Applicator
- Hose Inlet Diameter (cm): 0.476
- Hose Inlet Diameter (in): 3/16
- Hose Inlet Diameter (mm): 4.76
- Includes: Pump and Gun Air Controls
- Maximum Air Inlet Pressure (bar): 7
- Maximum Air Inlet Pressure (kPa): 700
- Maximum Air Inlet Pressure (psi): 100
- Maximum Flow Rate (GPM): 1.2
- Maximum Flow Rate (L/min): 4.5
- Maximum Working Pressure (bar): 69
- Maximum Working Pressure (kPa): 6900
- Maximum Working Pressure (psi): 1000
- Mount Type: Wall Mount
- Power Source: Air
- Pressure Type: High Pressure
- Product Type: Bare Package
- Pump Ratio: 10:1
- Pump Type: Pneumatic Piston Pump
REACTOR 2 H-XP2 SYSTEM, SEL, 15KW, PC
GG FPH062
REACTOR 2 H-XP2 SYSTEM, SEL, 15KW, PC
Graco FPH062 Reactor 2 H-XP2 Proportioner Package, Fusion PC Gun, Heated Hose, 15 kW, 230/400V
Graco&prime, s hydraulic Reactor H-XP2 brings increased yield and high output spraying. Ideal for in-plant OEM&prime, s or applicators that spray at high volumes.
Application: For coatings that require high-pressures - applies up to 1.5 gal (5.7 liters) per minute. Graco&prime, s line of hydraulic Reactors brings increased yield and high output spraying. Ideal for in-plant OEM&prime, s or applicators that spray at high volumes.- What a hydraulic system can do for you:
Dependability - robust, durable, longest life spray system
Reduce downtime - allows for longer time in between required maintenance
Increase daily productivity - capable of extremely high duty cycle
- Reactor Connect : Communication and Control at your Fingertips
Control your Reactor using your phone
Improve productivity and yield by optimizing spray parameters and never having to go back to your rig
Monitor your rigs/crews using the multi-system dashboard
Troubleshoot an issue quickly using real-time data
Provide documentation to a customer
Use reports to better manage your business
Saves all your spray data to the cloud
Utilize account management to better manage your equipment and crews
Reactor Connect comes standard with all Reactor 2 models
- Advanced control technology
Tracks, monitors and saves project data
Data can be saved and downloaded onto a USB drive
Stores up to 24 chemical recipes
Drum level indicators
- Sacrificial surge protector
Protects your electronics against excessive power spikes
- Three-year warranty
Covers user display and control modules
One of the best in the industry
- Model: Reactor 2
- Series: H-XP2
- Product Series: Non-Elite
- Amperage (A): 35 @ 350 to 415 V ac (3-Phase WYE), 59 @ 200 to 240 V ac (3-Phase Delta), 100 @ 200 to 240 V ac (1-Phase)
- Application: Protective Coatings
- Applicator Type: Manual
- Compatible Material: Plural Components
- Component Type: Two Component
- Flush Type: Solvent
- Frequency (Hz): 50/60
- Gun Type: Fusion PC
- Hose Length (ft): 50, 10
- Hose Length (m): 15, 3
- Hose Package: Single Hose
- Includes: Fusion PC Gun, Heated Hose, Whip Hose
- Material Application: Polyurea
- Maximum Flow Rate (cc/min): 5680
- Maximum Flow Rate (GPM): 2
- Maximum Flow Rate (L/min): 5.7
- Maximum Fluid Temperature (°C): 88
- Maximum Fluid Temperature (°F): 190
- Maximum Fluid Temperature (°C): 88
- Maximum Fluid Temperature (°F): 190
- Maximum Mix Ratio: 1:1
- Maximum Working Pressure (bar): 241
- Maximum Working Pressure (kPa): 24100
- Maximum Working Pressure (MPa): 24.1
- Maximum Worki
REACTOR 2 H-XP2 SYSTEM, SEL, 15KW, ELITE, PC
GG FPH162
REACTOR 2 H-XP2 SYSTEM, SEL, 15KW, ELITE, PC
Graco FPH162 Reactor 2 H-XP2 Elite Proportioner Package, Fusion PC Gun, Heated Hose, 15 kW, 230/400V
Graco&prime, s hydraulic Reactor H-XP2 brings increased yield and high output spraying. Ideal for in-plant OEM&prime, s or applicators that spray at high volumes.
Application: For coatings that require high-pressures - applies up to 1.5 gal (5.7 liters) per minute. Graco&prime, s line of hydraulic Reactors brings increased yield and high output spraying. Ideal for in-plant OEM&prime, s or applicators that spray at high volumes.- What a hydraulic system can do for you:
Dependability - robust, durable, longest life spray system
Reduce downtime - allows for longer time in between required maintenance
Increase daily productivity - capable of extremely high duty cycle
- Reactor Connect : Communication and Control at your Fingertips
Control your Reactor using your phone
Improve productivity and yield by optimizing spray parameters and never having to go back to your rig
Monitor your rigs/crews using the multi-system dashboard
Troubleshoot an issue quickly using real-time data
Provide documentation to a customer
Use reports to better manage your business
Saves all your spray data to the cloud
Utilize account management to better manage your equipment and crews
Reactor Connect comes standard with all Reactor 2 models
- Advanced control technology
Tracks, monitors and saves project data
Data can be saved and downloaded onto a USB drive
Stores up to 24 chemical recipes
Drum level indicators
- Sacrificial surge protector
Protects your electronics against excessive power spikes
- Three-year warranty
Covers user display and control modules
One of the best in the industry
- Elite Models
Graco InSite included
Inlet pressure and temperature sensors (interfaces with Graco InSite)
Xtreme-Wrap Scuff Guard on heated hoses when ordered as a package
- Model: Reactor 2
- Series: H-XP2
- Product Series: Elite
- Amperage (A): 35 @ 350 to 415 V ac (3-Phase WYE), 59 @ 200 to 240 V ac (3-Phase Delta), 100 @ 200 to 240 V ac (1-Phase)
- Application: Protective Coatings
- Applicator Type: Manual
- Compatible Material: Plural Components
- Component Type: Two Component
- Flush Type: Solvent
- Frequency (Hz): 50/60
- Gun Type: Fusion PC
- Hose Length (ft): 50, 10
- Hose Length (m): 15, 3
- Hose Package: Single Hose
- Includes: Fusion PC Gun, Heated Hose with Xtreme-Wrap, Heated Hose, Elite Kit
- Material Application: Polyurea
- Maximum Flow Rate (cc/min): 5680
- Maximum Flow Rate (GPM): 2
- Maximum Flow Rate (L/min): 5.7
- Maximum Fluid Temperature (°C): 88
- Maximum Fluid Temperature (°F): 190
- Maximum Fluid Temperature (°C): 88
- Maxi
REACTOR 2 H-XP3 SYSTEM, 230, 20KW, ELITE, PC
GG FHH174
REACTOR 2 H-XP3 SYSTEM, 230, 20KW, ELITE, PC
Graco FHH174 Reactor 2 H-XP3 Elite Proportioner Package, Fusion PC Gun, (6) Heated Hoses with Scuff Guard, 20 kW, 230 V, 3PH
Graco&prime, s hydraulic Reactor H-XP3 brings increased yield and high output spraying. Ideal for in-plant OEM&prime, s or applicators that spray at high volumes.
Application: For coatings that require high-pressures - applies up to 2.8 gal (10.6 liters) per minute.- What a hydraulic system can do for you:
Dependability - robust, durable, longest life spray system
Reduce downtime - allows for longer time in between required maintenance
Increase daily productivity - capable of extremely high duty cycle
- Reactor Connect : Communication and Control at your Fingertips
Control your Reactor using your phone
Improve productivity and yield by optimizing spray parameters and never having to go back to your rig
Monitor your rigs/crews using the multi-system dashboard
Troubleshoot an issue quickly using real-time data
Provide documentation to a customer
Use reports to better manage your business
Saves all your spray data to the cloud
Utilize account management to better manage your equipment and crews
Reactor Connect comes standard with all Reactor 2 models
- Advanced control technology
Tracks, monitors and saves project data
Data can be saved and downloaded onto a USB drive
Stores up to 24 chemical recipes
- Sacrificial surge protector
Protects your electronics against excessive power spikes
- Three-year warranty
Covers user display and control modules
One of the best in the industry
- Elite Models
Graco InSite included
Inlet pressure and temperature sensors (interfaces with Graco InSite)
Xtreme-Wrap Scuff Guard on heated hoses when ordered as a package
Drum level indicators
- Model: Reactor 2
- Series: H-XP3
- Product Series: Elite
- Amperage (A): 95 @ 200 to 240 V ac (3-Phase Delta)
- Application: Protective Coatings
- Applicator Type: Manual
- Compatible Material: Plural Components
- Component Type: Two Component
- Flush Type: Solvent
- Frequency (Hz): 50/60
- Gun Type: Fusion PC
- Hose Length (ft): 50, 10
- Hose Length (m): 15.2, 3
- Hose Package: Multi-Hose
- Includes: Proportioner, Fusion PC Gun, Heated Hose with Scuff Guard, Heated Whip Hose, Graco Insite, Fluid Inlet Sensors
- Material Application: Polyurea
- Maximum Flow Rate (cc/min): 9080
- Maximum Flow Rate (GPM): 2.4
- Maximum Flow Rate (L/min): 9.08
- Maximum Fluid Temperature (°C): 88
- Maximum Fluid Temperature (°F): 190
- Maximum Fluid Temperature (°C): 88
- Maximum Fluid Temperature (°F): 190
- Maximum Mix Ratio:
- Sacrificial surge protector
REACTOR 2 H-XP3 SYSTEM, 230, 20KW, ELITE, PC
GG FPH174
REACTOR 2 H-XP3 SYSTEM, 230, 20KW, ELITE, PC
Graco FPH174 Reactor 2 H-XP3 Elite Proportioner Package, Fusion PC Gun, Heated Hose with Scuff Guard, 20 kW, 230 V, 3PH
Graco&prime, s hydraulic Reactor H-XP3 brings increased yield and high output spraying. Ideal for in-plant OEM&prime, s or applicators that spray at high volumes.
Application: For coatings that require high-pressures - applies up to 2.8 gal (10.6 liters) per minute.- What a hydraulic system can do for you:
Dependability - robust, durable, longest life spray system
Reduce downtime - allows for longer time in between required maintenance
Increase daily productivity - capable of extremely high duty cycle
- Reactor Connect : Communication and Control at your Fingertips
Control your Reactor using your phone
Improve productivity and yield by optimizing spray parameters and never having to go back to your rig
Monitor your rigs/crews using the multi-system dashboard
Troubleshoot an issue quickly using real-time data
Provide documentation to a customer
Use reports to better manage your business
Saves all your spray data to the cloud
Utilize account management to better manage your equipment and crews
Reactor Connect comes standard with all Reactor 2 models
- Advanced control technology
Tracks, monitors and saves project data
Data can be saved and downloaded onto a USB drive
Stores up to 24 chemical recipes
- Sacrificial surge protector
Protects your electronics against excessive power spikes
- Three-year warranty
Covers user display and control modules
One of the best in the industry
- Elite Models
Graco InSite included
Inlet pressure and temperature sensors (interfaces with Graco InSite)
Xtreme-Wrap Scuff Guard on heated hoses when ordered as a package
Drum level indicators
- Model: Reactor 2
- Series: H-XP3
- Product Series: Elite
- Amperage (A): 95 @ 200 to 240 V ac (3-Phase Delta)
- Application: Protective Coatings
- Applicator Type: Manual
- Compatible Material: Plural Components
- Component Type: Two Component
- Flush Type: Solvent
- Frequency (Hz): 50/60
- Gun Type: Fusion PC
- Hose Length (ft): 50, 10
- Hose Length (m): 15, 3
- Hose Package: Single Hose
- Includes: Proportioner, Fusion PC Gun, Heated Hose with Scuff Guard, Heated Whip Hose, Graco Insite, Fluid Inlet Sensors
- Material Application: Polyurea
- Maximum Flow Rate (cc/min): 9080
- Maximum Flow Rate (GPM): 2.4
- Maximum Flow Rate (L/min): 9.08
- Maximum Fluid Temperature (°C): 88
- Maximum Fluid Temperature (°F): 190
- Maximum Fluid Temperature (°C): 88
- Maximum Fluid Temperature (°F): 190
- Maximum Mix Ratio: 1
- Sacrificial surge protector
RAC X FFLP TIP, SPRAY, (412)
GG FFLP412
RAC X FFLP TIP, SPRAY, (412)
Fine Finish Low Pressure RAC X FF LP SwitchTip, 412 Spray at up to 50% lower pressure with the Reverse-A-Clean (RAC) 412 Fine Finish Low Pressure (FF LP) RAC X SwitchTip. This fine finish tip produces an 8 to 10 inch Fan pattern and has a 0.012 inch orifice, ideal for finishing materials. Reverse the SwitchTip to easily clear clogs. For fine finish applications Less Prep & Cleanup Time- Less mess with less overspray
- Put the paint where you want it
- Softer spray fan pattern
- Easy to apply any material to any surfance
- Consistent blended finish quality
- Spraying at half pressure doubles tip life
- Reduced sprayer maintenance – up to 2X life
- Exclusive internal tip geometry
- Reduces energy required to atomize paints, stains, and other materials
- Delivers a superior finish with less pressure
- Works with SmartControl on select Graco sprayers
- Works with any airless sprayer
- Longest lasting Fan pattern
- Highest quality finish with a consistent spray pattern
- Large raised tip size numbers are always legible – even when covered with paint
- Locking tab ensures tip stays securely in guard
- Snaps tip in spray or reverse position
- OneSeal tip gasket installs with no tools
- Solvent seal available when using extremely hot solvents
MERKUR BELLOWS SYSTEM, PUMP, 150CC, STD
GG G05B09
MERKUR BELLOWS SYSTEM, PUMP, 150CC, STD
Merkur Bellows 5:1 Ratio Pump Package with U-Cup Seal, Wall Mount, Fluid Filter Graco’s Merkur bellows piston pumps provide low maintenance with no seals exposed to the atmosphere. These pumps are designed to eliminate conventional throat seals, providing high reliability for moisture-sensitive materials. Highest technology air motor on the market Low air consumption for increased efficiency Simple air motor design and minimal parts reduces repair time Easy-to-flush design allows for fast color changes and reduced material waste 300 series stainless steel pump construction provides long-lasting durability
MERKUR BELLOWS SYSTEM, PUMP, 150CC, SMT
GG G05B02
MERKUR BELLOWS SYSTEM, PUMP, 150CC, SMT
Merkur Bellows 5:1 Ratio Pump Package with V-Packing Seal, Wall Mount, Fluid Filter, DataTrak Graco’s Merkur bellows piston pumps provide low maintenance with no seals exposed to the atmosphere. These pumps are designed to eliminate conventional throat seals, providing high reliability for moisture-sensitive materials. Highest technology air motor on the market Low air consumption for increased efficiency Simple air motor design and minimal parts reduces repair time Easy-to-flush design allows for fast color changes and reduced material waste 300 series stainless steel pump construction provides long-lasting durability
MERKUR SYSTEM, PUMP, 3:1, 125CC, WALL, STD
GG G03W15
MERKUR SYSTEM, PUMP, 3:1, 125CC, WALL, STD
Graco G03W15 3:1 Merkur Air Spray Package, 125cc, Wall, No Applicator
Make the right choice for your finishing applications with Merkur Low Pressure Packages. The Merkur low-pressure piston pump comes with advanced air spray technology.
- Wall mount configuration offers easy access to data monitoring and controls.
- The air motor operates efficiently with low air consumption.
- The pump lower has the best solution for smooth, low pulsation operation.
- Model: Merkur
- Fluid Inlet Size (cm): 2.54
- Fluid Inlet Size (in): 1
- Fluid Inlet Size (mm): 25.4
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 1.27
- Fluid Outlet Size (in): 1/2
- Fluid Outlet Size (mm): 12.7
- Fluid Outlet Thread Type: NPT
- Gun Included: 0
- Gun Model: No Applicator
- Gun Technology: Bare Package
- Gun Type: No Applicator
- Maximum Air Pressure (bar): 6.9
- Maximum Air Pressure (kPa): 690
- Maximum Air Pressure (psi): 100
- Maximum Flow Rate (GPM): 2
- Maximum Flow Rate (L/min): 7.5
- Maximum Operating Temperature (°C): 49
- Maximum Operating Temperature (°F): 120
- Maximum Working Pressure (bar): 8.3
- Maximum Working Pressure (MPa): 0.8
- Maximum Working Pressure (psi): 120
- Mount Type: Wall Mount
- Power Source: Air
- Pressure Type: Low Pressure
- Product Type: Bare Package
- Pump Ratio: 3:1
- Pump Type: Pneumatic Piston Pump
RAC X FFLP TIP, SPRAY, (310)
GG FFLP310
RAC X FFLP TIP, SPRAY, (310)
Fine Finish Low Pressure RAC X FF LP SwitchTip, 310 Spray at up to 50% lower pressure with the Reverse-A-Clean (RAC) 310 Fine Finish Low Pressure (FF LP) RAC X SwitchTip. This fine finish tip produces a 6 to 8 inch Fan pattern and has a 0.010 inch orifice, ideal for finishing materials. Reverse the SwitchTip to easily clear clogs. For fine finish applications Less Prep & Cleanup Time- Less mess with less overspray
- Put the paint where you want it
- Softer spray fan pattern
- Easy to apply any material to any surfance
- Consistent blended finish quality
- Spraying at half pressure doubles tip life
- Reduced sprayer maintenance – up to 2X life
- Exclusive internal tip geometry
- Reduces energy required to atomize paints, stains, and other materials
- Delivers a superior finish with less pressure
- Works with SmartControl on select Graco sprayers
- Works with any airless sprayer
- Longest lasting Fan pattern
- Highest quality finish with a consistent spray pattern
- Large raised tip size numbers are always legible – even when covered with paint
- Locking tab ensures tip stays securely in guard
- Snaps tip in spray or reverse position
- OneSeal tip gasket installs with no tools
- Solvent seal available when using extremely hot solvents
MERKUR SYSTEM, PUMP, 10:1, 75CC, CART, STD
GG G10C09
MERKUR SYSTEM, PUMP, 10:1, 75CC, CART, STD
10:1 Merkur AA Package, 1.2 gpm (4.5 lpm) fluid flow, Cart Mount, PerformAA 15 Gun, Pump Air Controls, Gun Air/Fluid Hose, Fluid Filter Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications. Proven to outperform and outlast other pumps in their class Highest technology air motor on the market Low air consumption for increased efficiency External valve access allows for easy servicing and online replacement to minimize downtime
MERKUR SYSTEM, PUMP, 3:1, 125CC, WALL, STD
GG G03W03
MERKUR SYSTEM, PUMP, 3:1, 125CC, WALL, STD
Graco G03W03 3:1 Merkur Air Spray Package, 125cc, Wall, Pump/Gun Air Controls, Siphon Kit, Fluid Filter, No Applicator
Make the right choice for your finishing applications with Merkur Low Pressure Packages. The Merkur low-pressure piston pump comes with advanced air spray technology.
- The pump lower has the best solution for smooth, low pulsation operation.
- The air motor operates efficiently with low air consumption.
- Wall mount configuration offers easy access to data monitoring and controls.
- Model: Merkur
- Fluid Inlet Size (cm): 2.54
- Fluid Inlet Size (in): 1
- Fluid Inlet Size (mm): 25.4
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 1.27
- Fluid Outlet Size (in): 1/2
- Fluid Outlet Size (mm): 12.7
- Fluid Outlet Thread Type: NPT
- Gun Included: 0
- Gun Model: No Applicator
- Gun Technology: Bare Package
- Gun Type: No Applicator
- Includes: Pump and Gun Air Controls, Siphon Kit, Fluid Filter
- Maximum Air Pressure (bar): 6.9
- Maximum Air Pressure (kPa): 690
- Maximum Air Pressure (psi): 100
- Maximum Flow Rate (GPM): 2
- Maximum Flow Rate (L/min): 7.5
- Maximum Operating Temperature (°C): 49
- Maximum Operating Temperature (°F): 120
- Maximum Working Pressure (bar): 8.3
- Maximum Working Pressure (MPa): 0.8
- Maximum Working Pressure (psi): 120
- Mount Type: Wall Mount
- Power Source: Air
- Pressure Type: Low Pressure
- Product Type: Bare Package
- Pump Ratio: 3:1
- Pump Type: Pneumatic Piston Pump
MERKUR SYSTEM, PUMP, 10:1, 75CC, CART, STD
GG G10C03
MERKUR SYSTEM, PUMP, 10:1, 75CC, CART, STD
Graco G10C03 10:1 Merkur Pump, 1.2 gpm (4.5 lpm) fluid flow, Cart Mount, Pump/Gun Air Controls, Suction Hose
Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications.
- Proven to outperform and outlast other pumps in their class
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Model: Merkur
- Compatible Material: Waterborne, Solvent borne, High Solids, Single Components, Topcoats, Varnish, Lacquer, Acid Catalysts, Enamel, UV Coating
- Fluid Inlet Size (cm): 1.905
- Fluid Inlet Size (in): 3/4
- Fluid Inlet Size (mm): 19.05
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 0.9525
- Fluid Outlet Size (in): 3/8
- Fluid Outlet Size (mm): 9.525
- Fluid Outlet Thread Type: NPT
- Gun Included: 0
- Gun Model: No Applicator
- Gun Technology: Bare Package
- Gun Type: No Applicator
- Hose Inlet Diameter (cm): 0.476
- Hose Inlet Diameter (in): 3/16
- Hose Inlet Diameter (mm): 4.76
- Includes: Pump and Gun Air Controls, Suction Hose
- Maximum Air Inlet Pressure (bar): 7
- Maximum Air Inlet Pressure (kPa): 700
- Maximum Air Inlet Pressure (psi): 100
- Maximum Flow Rate (GPM): 1.2
- Maximum Flow Rate (L/min): 4.5
- Maximum Working Pressure (bar): 69
- Maximum Working Pressure (kPa): 6900
- Maximum Working Pressure (psi): 1000
- Mount Type: Cart Mount
- Power Source: Air
- Pressure Type: High Pressure
- Product Type: Bare Package
- Pump Ratio: 10:1
- Pump Type: Pneumatic Piston Pump
10:1 Merkur Pump, 1.2 gpm (4.5 lpm) fluid flow, Wall Mount, Pump/Gun Air Controls, Suction Hose
GG G10W03
MERKUR SYSTEM PUMP 10:01 75CC WA STD
Graco G10W03 10:1 Merkur Pump, 1.2 gpm (4.5 lpm) fluid flow, Wall Mount, Pump/Gun Air Controls, Suction Hose
Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications.
- Proven to outperform and outlast other pumps in their class
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Model: Merkur
- Compatible Material: Waterborne, Solventborne, High Solids, Single Components, Topcoats, Varnish, Lacquer, Acid Catalysts, Enamel, UV Coating
- Fluid Inlet Size (cm): 1.905
- Fluid Inlet Size (in): 3/4
- Fluid Inlet Size (mm): 19.05
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 0.9525
- Fluid Outlet Size (in): 3/8
- Fluid Outlet Size (mm): 9.525
- Fluid Outlet Thread Type: NPT
- Gun Included: 0
- Gun Model: No Applicator
- Gun Technology: Bare Package
- Gun Type: No Applicator
- Hose Inlet Diameter (cm): 0.476
- Hose Inlet Diameter (in): 3/16
- Hose Inlet Diameter (mm): 4.76
- Includes: Pump and Gun Air Controls, Suction Hose
- Maximum Air Inlet Pressure (bar): 7
- Maximum Air Inlet Pressure (kPa): 700
- Maximum Air Inlet Pressure (psi): 100
- Maximum Flow Rate (GPM): 1.2
- Maximum Flow Rate (L/min): 4.5
- Maximum Working Pressure (bar): 69
- Maximum Working Pressure (kPa): 6900
- Maximum Working Pressure (psi): 1000
- Mount Type: Wall Mount
- Power Source: Air
- Pressure Type: High Pressure
- Product Type: Bare Package
- Pump Ratio: 10:1
- Pump Type: Pneumatic Piston Pump
MERKUR BELLOWS SYSTEM, PUMP, 50CC, STD
GG G15B01
MERKUR BELLOWS SYSTEM, PUMP, 50CC, STD
Merkur Bellows 15:1 Ratio Pump Package with V-Packing Seal, Wall Mount, Fluid Filter Graco’s Merkur bellows piston pumps provide low maintenance with no seals exposed to the atmosphere. These pumps are designed to eliminate conventional throat seals, providing high reliability for moisture-sensitive materials. Highest technology air motor on the market Low air consumption for increased efficiency Simple air motor design and minimal parts reduces repair time Easy-to-flush design allows for fast color changes and reduced material waste 300 series stainless steel pump construction provides long-lasting durability
MERKUR SYSTEM PUMP 10:01 75CC WALL STD
GG G10W05
MERKUR SYSTEM PUMP 10:01 75CC WALL STD
Graco G10W05 10:1 Merkur AA Package, 1.2 gpm (4.5 lpm) fluid flow, Wall Mount, PerformAA 15 Gun, Pump Air Controls, Gun Air/Fluid Hose, Suction Hose
Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications.
- Proven to outperform and outlast other pumps in their class
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Model: Merkur
- Convertible: Non-Convertible
- Fluid Inlet Size (cm): 1.905
- Fluid Inlet Size (in): 3/4
- Fluid Inlet Size (mm): 19.05
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 0.9525
- Fluid Outlet Size (in): 3/8
- Fluid Outlet Size (mm): 9.525
- Fluid Outlet Thread Type: NPT
- Gun Included: 1
- Gun Model: PerformAA 15 Air Assist
- Gun Technology: Air-Assisted
- Gun Type: Air-Assisted
- Hose Inlet Diameter (cm): 0.4763
- Hose Inlet Diameter (in): 0.1875
- Hose Inlet Diameter (mm): 5
- Includes: Pump and Gun Air Controls, Gun Hose, Suction Hose
- Maximum Flow Rate (GPM): 1.2
- Maximum Hose Length (ft): 25
- Maximum Hose Length (m): 7.6
- Maximum Working Pressure (bar): 69
- Maximum Working Pressure (kPa): 6900
- Maximum Working Pressure (MPa): 6.9
- Maximum Working Pressure (psi): 1000
- Motor Type: Pneumatic
- Mount Type: Wall Mount
- Number of Guns: 1
- Power Source: Air
- Pressure Type: High Pressure
- Product Type: Spray Package
- Pump Ratio: 10:1
- Pump Type: Pneumatic Piston Pump
MERKUR SYSTEM PUMP 10:1 75CC WALL STD
GG G10W07
MERKUR SYSTEM PUMP 10:1 75CC WALL STD
Graco G10W07 10:1 Merkur AA Package, 1.2 gpm (4.5 lpm) fluid flow, Wall Mount, PerformAA 15 Gun, Pump Air Controls, Gun Air/Fluid Hose, Filter
Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications.
- Proven to outperform and outlast other pumps in their class
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Model: Merkur
- Convertible: Non-Convertible
- Fluid Inlet Size (cm): 1.905
- Fluid Inlet Size (in): 3/4
- Fluid Inlet Size (mm): 19.05
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 0.9525
- Fluid Outlet Size (in): 3/8
- Fluid Outlet Size (mm): 9.525
- Fluid Outlet Thread Type: NPT
- Gun Included: 1
- Gun Model: PerformAA 15 Air Assist
- Gun Technology: Air-Assisted
- Gun Type: Air-Assisted
- Hose Inlet Diameter (cm): 0.4763
- Hose Inlet Diameter (in): 0.1875
- Hose Inlet Diameter (mm): 5
- Includes: Pump and Gun Air Controls, Gun Hose, Suction Hose, Fluid Filter
- Maximum Flow Rate (GPM): 1.2
- Maximum Hose Length (ft): 25
- Maximum Hose Length (m): 7.6
- Maximum Working Pressure (bar): 69
- Maximum Working Pressure (kPa): 6900
- Maximum Working Pressure (MPa): 6.9
- Maximum Working Pressure (psi): 1000
- Motor Type: Pneumatic
- Mount Type: Wall Mount
- Number of Guns: 1
- Power Source: Air
- Pressure Type: High Pressure
- Product Type: Spray Package
- Pump Ratio: 10:1
- Pump Type: Pneumatic Piston Pump
MERKUR BELLOWS SYSTEM, PUMP, 50CC, SMT
GG G15B04
MERKUR BELLOWS SYSTEM, PUMP, 50CC, SMT
Graco G15B04 Merkur Bellows 15:1 Ratio Air-Assisted Airless Package with V-Packing, Wall Mount, Fluid Filter, Hoses, PerformAA 15 Spray Gun, DataTrak
Graco’s Merkur bellows piston pumps provide low maintenance with no seals exposed to the atmosphere. These pumps are designed to eliminate conventional throat seals, providing high reliability for moisture-sensitive materials.
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Simple air motor design and minimal parts reduces repair time
- 300 series stainless steel pump construction provides long-lasting durability
- Model: Merkur
- Series: Bellows
- Application: Supply
- Compatible Material: Waterborne, Solvent borne, High Solids, Xirallic, CARC, Metallics, Topcoats, Stains, Varnish, UV Coating
- Convertible: Non-Convertible
- Fluid Inlet Size (cm): 1.905
- Fluid Inlet Size (in): 3/4
- Fluid Inlet Size (mm): 19.05
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 0.9525
- Fluid Outlet Size (in): 3/8
- Fluid Outlet Size (mm): 9.525
- Fluid Outlet Thread Type: NPT
- Frame Configuration: Wall
- Gun Included: 1
- Gun Model: G15
- Gun Technology: Air-Assisted
- Gun Type: Air-Assisted
- Includes: Pump and Gun Air Controls, Drain Valves, Fluid Filter, DataTrak, V-Packing
- Maximum Flow Rate (GPM): 0.8
- Maximum Hose Length (ft): 25
- Maximum Hose Length (m): 7.6
- Maximum Working Pressure (bar): 103
- Maximum Working Pressure (kPa): 10300
- Maximum Working Pressure (MPa): 10.3
- Maximum Working Pressure (psi): 1500
- Motor Type: Pneumatic
- Mount Type: Wall Mount
- Number of Guns: 1
- Outlet Paint Filter: 60 Mesh Stainless Steel Screen
- Power Source: Air
- Pressure Type: High Pressure
- Product Type: Spray Package
- Pump Ratio: 15:1
- Pump Type: Pneumatic Piston Pump
MERKUR BELLOWS SYSTEM, PUMP, 150CC, SMT
GG G15B52
MERKUR BELLOWS SYSTEM, PUMP, 150CC, SMT
Graco G15B52 Merkur™ Bellows 15:1 Ratio Pump Package with Wall Mount, V-Packing & DataTrak
The gentle pumping action of the Merkur Bellows Pump, combined with reduced sealing surfaces, provides superior handling of shear-sensitive materials, including UV coatings and waterborne materials.
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Simple air motor design and minimal parts reduces repair time
- 300 series stainless steel pump construction provides long-lasting durability
- Fewer parts and online replacement bellows seal means improved serviceability, lower cost of ownership and reduced downtime
- Model: Merkur
- Series: Bellows
- Application: Supply
- Compatible Material: Waterborne, Solvent borne, High Solids, Xirallic, CARC, Metallics, Topcoats, Stains, Varnish, UV Coating
- Fluid Inlet Size (cm): 2.5400
- Fluid Inlet Size (in): 1
- Fluid Inlet Size (mm): 25.4000
- Fluid Inlet Thread Gender: Male
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 1.905
- Fluid Outlet Size (in): 3/4
- Fluid Outlet Size (mm): 19.05
- Fluid Outlet Thread Gender: Male
- Fluid Outlet Thread Type: NPT
- Includes: Pump Only Air Controls, Fluid Filter, DataTrak Monitor
- Material: Stainless Steel
- Maximum Flow Rate (gpm @ 60 cpm): 2.4
- Maximum Operating Temperature (°F): 120
- Maximum Working Pressure (bar): 103
- Maximum Working Pressure (kPa): 10300
- Maximum Working Pressure (MPa): 10.3
- Maximum Working Pressure (psi): 1500
- Motor Type: Pneumatic
- Mount Location: Wall Mount
- Number of Pieces: 3
MERKUR BELLOWS SYSTEM, PUMP, 150CC, STD
GG G15B59
MERKUR BELLOWS SYSTEM, PUMP, 150CC, STD
Merkur™ Bellows 15:1 Ratio Pump Package with Wall Mount & V-Packing The gentle pumping action of the Merkur Bellows Pump, combined with reduced sealing surfaces, provides superior handling of shear-sensitive materials, including UV coatings and waterborne materials. Highest technology air motor on the market Low air consumption for increased efficiency Simple air motor design and minimal parts reduces repair time Easy-to-flush design allows for fast color changes and reduced material waste 300 series stainless steel pump construction provides long-lasting durability Fewer parts and online replacement bellows seal means improved serviceability, lower cost of ownership and reduced downtime
MERKUR SYSTEM, PUMP, 15:1, 25CC, CART, STD
GG G15C07
MERKUR SYSTEM, PUMP, 15:1, 25CC, CART, STD
Graco G15C07 15:1 Merkur AA Package, 0.4 gpm (1.5 lpm) fluid flow, Cart Mount, PerformAA 15 Gun, Pump Air Controls, Gun Air/Fluid Hose, Suction Hose
Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications.
- Proven to outperform and outlast other pumps in their class
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Model: Merkur
- Convertible: Non-Convertible
- Fluid Inlet Size (cm): 1.27
- Fluid Inlet Size (in): 1/2
- Fluid Inlet Size (mm): 12.7
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 0.9525
- Fluid Outlet Size (in): 3/8
- Fluid Outlet Size (mm): 9.525
- Fluid Outlet Thread Type: NPT
- Gun Included: 1
- Gun Model: PerformAA 15 Air Assist
- Gun Technology: Air-Assisted
- Gun Type: Air-Assisted
- Hose Inlet Diameter (cm): 0.4763
- Hose Inlet Diameter (in): 0.1875
- Hose Inlet Diameter (mm): 5
- Includes: Pump and Gun Air Controls, Gun Hose, Suction Hose
- Maximum Flow Rate (GPM): 0.4
- Maximum Hose Length (ft): 25
- Maximum Hose Length (m): 7.6
- Maximum Working Pressure (bar): 103
- Maximum Working Pressure (kPa): 10300
- Maximum Working Pressure (MPa): 10.3
- Maximum Working Pressure (psi): 1500
- Motor Type: Pneumatic
- Mount Type: Cart Mount
- Number of Guns: 1
- Power Source: Air
- Pressure Type: High Pressure
- Product Type: Spray Package
- Pump Ratio: 15:1
- Pump Type: Pneumatic Piston Pump
MERKUR SYSTEM, PUMP, 15:1, 25CC, 1LEG, STD
GG G15T03
MERKUR SYSTEM, PUMP, 15:1, 25CC, 1LEG, STD
Graco G15T03 15:1 Merkur AA Package, 0.4 gpm (1.5 lpm) fluid flow, Stand Mount, PerformAA 15 Gun, Pump Air Controls, Gun Air/Fluid Hose, Suction Hose
Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications.
- Proven to outperform and outlast other pumps in their class
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Model: Merkur
- Convertible: Non-Convertible
- Fluid Inlet Size (cm): 1.27
- Fluid Inlet Size (in): 1/2
- Fluid Inlet Size (mm): 12.7
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 0.9525
- Fluid Outlet Size (in): 3/8
- Fluid Outlet Size (mm): 9.525
- Fluid Outlet Thread Type: NPT
- Gun Included: 1
- Gun Model: PerformAA 15 Air Assist
- Gun Technology: Air-Assisted
- Gun Type: Air-Assisted
- Hose Inlet Diameter (cm): 0.4763
- Hose Inlet Diameter (in): 0.1875
- Hose Inlet Diameter (mm): 5
- Includes: Pump and Gun Air Controls, Gun Hose, Suction Hose
- Maximum Flow Rate (GPM): 0.4
- Maximum Hose Length (ft): 25
- Maximum Hose Length (m): 7.6
- Maximum Working Pressure (bar): 103
- Maximum Working Pressure (kPa): 10300
- Maximum Working Pressure (MPa): 10.3
- Maximum Working Pressure (psi): 1500
- Motor Type: Pneumatic
- Mount Type: Stand Mount
- Number of Guns: 1
- Power Source: Air
- Pressure Type: High Pressure
- Product Type: Spray Package
- Pump Ratio: 15:1
- Pump Type: Pneumatic Piston Pump
MERKUR SYSTEM, PUMP, 15:1, 25CC, CART, STD
GG G15C09
MERKUR SYSTEM, PUMP, 15:1, 25CC, CART, STD
15:1 Merkur AA Package, 0.4 gpm (1.5 lpm) fluid flow, Cart Mount, PerformAA 15 Gun, Pump/Gun Air Controls, Gun Air/Fluid Hose, Fluid Filter Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications. Proven to outperform and outlast other pumps in their class Highest technology air motor on the market Low air consumption for increased efficiency External valve access allows for easy servicing and online replacement to minimize downtime
MERKUR SYSTEM, PUMP, 15:1, 50CC, CART, STD
GG G15C29
MERKUR SYSTEM, PUMP, 15:1, 50CC, CART, STD
Graco G15C29 15:1 Merkur AA Package, 0.8 gpm (3 lpm) fluid flow, Cart Mount, PerformAA 15 Gun, Pump Air Controls, Gun Air/Fluid Hose, Fluid Filter
Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications.
- Proven to outperform and outlast other pumps in their class
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Model: Merkur
- Convertible: Non-Convertible
- Fluid Inlet Size (cm): 1.905
- Fluid Inlet Size (in): 3/4
- Fluid Inlet Size (mm): 19.05
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 0.9525
- Fluid Outlet Size (in): 3/8
- Fluid Outlet Size (mm): 9.525
- Fluid Outlet Thread Type: NPT
- Gun Included: 1
- Gun Model: PerformAA 15 Air Assist
- Gun Technology: Air-Assisted
- Gun Type: Air-Assisted
- Hose Inlet Diameter (cm): 0.4763
- Hose Inlet Diameter (in): 0.1875
- Hose Inlet Diameter (mm): 5
- Includes: Pump and Gun Air Controls, Gun Hose, Suction Hose, Fluid Filter
- Maximum Flow Rate (GPM): 0.8
- Maximum Hose Length (ft): 25
- Maximum Hose Length (m): 7.6
- Maximum Working Pressure (bar): 103
- Maximum Working Pressure (kPa): 10300
- Maximum Working Pressure (MPa): 10.3
- Maximum Working Pressure (psi): 1500
- Motor Type: Pneumatic
- Mount Type: Cart Mount
- Number of Guns: 1
- Power Source: Air
- Pressure Type: High Pressure
- Product Type: Spray Package
- Pump Ratio: 15:1
- Pump Type: Pneumatic Piston Pump
MERKUR SYSTEM, PUMP, 15:1, 25CC, WALL, STD
GG G15W07
MERKUR SYSTEM, PUMP, 15:1, 25CC, WALL, STD
Graco G15W07 15:1 Merkur AA Package, 0.4 gpm (1.5 lpm) fluid flow, Wall Mount, PerformAA 15 Gun, Pump Air Controls, Gun Air/Fluid Hose, Fluid Filter
Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications.
- Proven to outperform and outlast other pumps in their class
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Model: Merkur
- Convertible: Non-Convertible
- Fluid Inlet Size (cm): 1.27
- Fluid Inlet Size (in): 1/2
- Fluid Inlet Size (mm): 12.7
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 0.9525
- Fluid Outlet Size (in): 3/8
- Fluid Outlet Size (mm): 9.525
- Fluid Outlet Thread Type: NPT
- Gun Included: 1
- Gun Model: PerformAA 15 Air Assist
- Gun Technology: Air-Assisted
- Gun Type: Air-Assisted
- Hose Inlet Diameter (cm): 0.4763
- Hose Inlet Diameter (in): 0.1875
- Hose Inlet Diameter (mm): 5
- Includes: Pump and Gun Air Controls, Gun Hose, Suction Hose, Fluid Filter
- Maximum Flow Rate (GPM): 0.4
- Maximum Hose Length (ft): 25
- Maximum Hose Length (m): 7.6
- Maximum Working Pressure (bar): 103
- Maximum Working Pressure (kPa): 10300
- Maximum Working Pressure (MPa): 10.3
- Maximum Working Pressure (psi): 1500
- Motor Type: Pneumatic
- Mount Type: Wall Mount
- Number of Guns: 1
- Power Source: Air
- Pressure Type: High Pressure
- Product Type: Spray Package
- Pump Ratio: 15:1
- Pump Type: Pneumatic Piston Pump
MERKUR SYSTEM PUMP 15:01 50CC WA STD
GG G15W21
MERKUR SYSTEM PUMP 15:01 50CC WA STD
Graco G15W21 15:1 Merkur Pump, 0.8 gpm (3 lpm) fluid flow, Wall Mount, Pump/Gun Air Controls
Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications.
- Proven to outperform and outlast other pumps in their class
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Model: Merkur
- Compatible Material: Waterborne, Solvent borne, High Solids, Single Components, Topcoats, Varnish, Lacquer, Acid Catalysts, Enamel, UV Coating
- Fluid Inlet Size (cm): 1.905
- Fluid Inlet Size (in): 3/4
- Fluid Inlet Size (mm): 19.05
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 0.9525
- Fluid Outlet Size (in): 3/8
- Fluid Outlet Size (mm): 9.525
- Fluid Outlet Thread Type: NPT
- Gun Included: 0
- Gun Model: No Applicator
- Gun Technology: Bare Package
- Gun Type: No Applicator
- Hose Inlet Diameter (cm): 0.476
- Hose Inlet Diameter (in): 3/16
- Hose Inlet Diameter (mm): 4.76
- Includes: Pump and Gun Air Controls
- Maximum Air Inlet Pressure (bar): 7
- Maximum Air Inlet Pressure (kPa): 700
- Maximum Air Inlet Pressure (psi): 100
- Maximum Flow Rate (GPM): 0.8
- Maximum Flow Rate (L/min): 3.0
- Maximum Working Pressure (bar): 103
- Maximum Working Pressure (kPa): 10300
- Maximum Working Pressure (psi): 1500
- Mount Type: Wall Mount
- Power Source: Air
- Pressure Type: High Pressure
- Product Type: Bare Package
- Pump Ratio: 15:1
- Pump Type: Pneumatic Piston Pump
MERKUR SYSTEM, PUMP, 15:1, 50CC, CART, STD
GG G15C27
MERKUR SYSTEM, PUMP, 15:1, 50CC, CART, STD
15:1 Merkur AA Package, 0.8 gpm (3 lpm) fluid flow, Cart Mount, PerformAA 15 Gun, Pump Air Controls, Gun Air/Fluid Hose, Suction Hose Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications. Proven to outperform and outlast other pumps in their class Highest technology air motor on the market Low air consumption for increased efficiency External valve access allows for easy servicing and online replacement to minimize downtime
MERKUR SYSTEM PUMP 15:01 25CC WALL STD
GG G15W01
MERKUR SYSTEM PUMP 15:01 25CC WALL STD
Graco G15W01 15:1 Merkur Pump, 0.4 gpm (1.5 lpm) fluid flow, Wall Mount, Pump/Gun Air Controls
Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications.
- Proven to outperform and outlast other pumps in their class
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Model: Merkur
- Compatible Material: Waterborne, Solvent borne, High Solids, Single Components, Topcoats, Varnish, Lacquer, Acid Catalysts, Enamel, UV Coating
- Fluid Inlet Size (cm): 1.27
- Fluid Inlet Size (in): 1/2
- Fluid Inlet Size (mm): 12.7
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 0.9525
- Fluid Outlet Size (in): 3/8
- Fluid Outlet Size (mm): 9.525
- Fluid Outlet Thread Type: NPT
- Gun Included: 0
- Gun Model: No Applicator
- Gun Technology: Bare Package
- Gun Type: No Applicator
- Hose Inlet Diameter (cm): 0.476
- Hose Inlet Diameter (in): 3/16
- Hose Inlet Diameter (mm): 4.76
- Includes: Pump and Gun Air Controls
- Maximum Air Inlet Pressure (bar): 7
- Maximum Air Inlet Pressure (kPa): 700
- Maximum Air Inlet Pressure (psi): 100
- Maximum Flow Rate (GPM): 0.4
- Maximum Flow Rate (L/min): 1.5
- Maximum Working Pressure (bar): 103
- Maximum Working Pressure (kPa): 10300
- Maximum Working Pressure (psi): 1500
- Mount Type: Wall Mount
- Power Source: Air
- Pressure Type: High Pressure
- Product Type: Bare Package
- Pump Ratio: 15:1
- Pump Type: Pneumatic Piston Pump
MERKUR SYSTEM PUMP 15:01 25CC WALL STD
GG G15W09
MERKUR SYSTEM PUMP 15:01 25CC WALL STD
Graco G15W09 15:1 Merkur Pump, 0.4 gpm (1.5 lpm) fluid flow, Wall Mount
Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications.
- Proven to outperform and outlast other pumps in their class
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Model: Merkur
- Compatible Material: Waterborne, Solvent borne, High Solids, Single Components, Topcoats, Varnish, Lacquer, Acid Catalysts, Enamel, UV Coating
- Fluid Inlet Size (cm): 1.27
- Fluid Inlet Size (in): 1/2
- Fluid Inlet Size (mm): 12.7
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 0.9525
- Fluid Outlet Size (in): 3/8
- Fluid Outlet Size (mm): 9.525
- Fluid Outlet Thread Type: NPT
- Gun Included: 0
- Gun Model: No Applicator
- Gun Technology: Bare Package
- Gun Type: No Applicator
- Hose Inlet Diameter (cm): 0.476
- Hose Inlet Diameter (in): 3/16
- Hose Inlet Diameter (mm): 4.76
- Maximum Air Inlet Pressure (bar): 7
- Maximum Air Inlet Pressure (kPa): 700
- Maximum Air Inlet Pressure (psi): 100
- Maximum Flow Rate (GPM): 0.4
- Maximum Flow Rate (L/min): 1.5
- Maximum Working Pressure (bar): 103
- Maximum Working Pressure (kPa): 10300
- Maximum Working Pressure (psi): 1500
- Mount Type: Wall Mount
- Power Source: Air
- Pressure Type: High Pressure
- Product Type: Bare Package
- Pump Ratio: 15:1
- Pump Type: Pneumatic Piston Pump
MERKUR SYSTEM, PUMP, 15:1, 50CC, CART, STD
GG G15C23
MERKUR SYSTEM, PUMP, 15:1, 50CC, CART, STD
Graco G15C23 15:1 Merkur Pump, 0.8 gpm (3 lpm) fluid flow, Cart Mount, Pump/Gun Air Controls, Suction Hose
Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications.
- Proven to outperform and outlast other pumps in their class
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Model: Merkur
- Compatible Material: Waterborne, Solvent borne, High Solids, Single Components, Topcoats, Varnish, Lacquer, Acid Catalysts, Enamel, UV Coating
- Fluid Inlet Size (cm): 1.905
- Fluid Inlet Size (in): 3/4
- Fluid Inlet Size (mm): 19.05
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 0.9525
- Fluid Outlet Size (in): 3/8
- Fluid Outlet Size (mm): 9.525
- Fluid Outlet Thread Type: NPT
- Gun Included: 0
- Gun Model: No Applicator
- Gun Technology: Bare Package
- Gun Type: No Applicator
- Hose Inlet Diameter (cm): 0.476
- Hose Inlet Diameter (in): 3/16
- Hose Inlet Diameter (mm): 4.76
- Includes: Pump and Gun Air Controls, Suction Hose
- Maximum Air Inlet Pressure (bar): 7
- Maximum Air Inlet Pressure (kPa): 700
- Maximum Air Inlet Pressure (psi): 100
- Maximum Flow Rate (GPM): 0.8
- Maximum Flow Rate (L/min): 3.0
- Maximum Working Pressure (bar): 103
- Maximum Working Pressure (kPa): 10300
- Maximum Working Pressure (psi): 1500
- Mount Type: Cart Mount
- Power Source: Air
- Pressure Type: High Pressure
- Product Type: Bare Package
- Pump Ratio: 15:1
- Pump Type: Pneumatic Piston Pump
Merkur System Pump 15:01 Cart Mount
GG G15C80
Merkur System Pump 15:01 Cart Mount
MERKUR SYSTEM PUMP 15:1 50CC WALL STD
GG G15W27
MERKUR SYSTEM PUMP 15:1 50CC WALL STD
15:1 Merkur AA Package, 0.8 gpm (3 lpm) fluid flow, Wall Mount, PerformAA 15 Gun, Pump Air Controls, Gun Air/Fluid Hose, Fluid Filter Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications. Proven to outperform and outlast other pumps in their class Highest technology air motor on the market Low air consumption for increased efficiency External valve access allows for easy servicing and online replacement to minimize downtime
MERKUR SYSTEM PUMP 15:1 150CC CART STD
GG G15C83
MERKUR SYSTEM PUMP 15:1 150CC CART STD
15:1 Merkur Pump, 2.4 gpm (9 lpm) fluid flow, Cart Mount, PerformAA 15, Pump Air Controls, Gun Air/Fluid Hose, Suction Hose, Filter Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications. Proven to outperform and outlast other pumps in their class Highest technology air motor on the market Low air consumption for increased efficiency External valve access allows for easy servicing and online replacement to minimize downtime
MERKUR SYSTEM PUMP 15:1 25CC WA STD
GG G15W03
MERKUR SYSTEM PUMP 15:1 25CC WA STD
Graco G15W03 15:1 Merkur Pump, 0.4 gpm (1.5 lpm) fluid flow, Wall Mount, Pump/Gun Air Controls, Suction Hose
Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications.
- Proven to outperform and outlast other pumps in their class
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Model: Merkur
- Compatible Material: Waterborne, Solvent borne, High Solids, Single Components, Topcoats, Varnish, Lacquer, Acid Catalysts, Enamel, UV Coating
- Fluid Inlet Size (cm): 1.27
- Fluid Inlet Size (in): 1/2
- Fluid Inlet Size (mm): 12.7
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 0.9525
- Fluid Outlet Size (in): 3/8
- Fluid Outlet Size (mm): 9.525
- Fluid Outlet Thread Type: NPT
- Gun Included: 0
- Gun Model: No Applicator
- Gun Technology: Bare Package
- Gun Type: No Applicator
- Hose Inlet Diameter (cm): 0.476
- Hose Inlet Diameter (in): 3/16
- Hose Inlet Diameter (mm): 4.76
- Includes: Pump and Gun Air Controls, Suction Hose
- Maximum Air Inlet Pressure (bar): 7
- Maximum Air Inlet Pressure (kPa): 700
- Maximum Air Inlet Pressure (psi): 100
- Maximum Flow Rate (GPM): 0.4
- Maximum Flow Rate (L/min): 1.5
- Maximum Working Pressure (bar): 103
- Maximum Working Pressure (kPa): 10300
- Maximum Working Pressure (psi): 1500
- Mount Type: Wall Mount
- Power Source: Air
- Pressure Type: High Pressure
- Product Type: Bare Package
- Pump Ratio: 15:1
- Pump Type: Pneumatic Piston Pump
MERKUR SYSTEM PUMP 15:01 150CC CT STD
GG G15C77
MERKUR SYSTEM PUMP 15:01 150CC CT STD
Graco G15C77 15:1 Merkur Pump, 2.4 gpm (9 lpm) fluid flow, Cart Mount, Pump Air Controls
Designed to improve productivity, reduce costs, lower emissions and provide consistent, high quality finishes for all of your demanding applications.
- Proven to outperform and outlast other pumps in their class
- Highest technology air motor on the market
- Low air consumption for increased efficiency
- Model: Merkur
- Compatible Material: Waterborne, Solvent borne, High Solids, Single Components, Topcoats, Varnish, Lacquer, Acid Catalysts, Enamel, UV Coating
- Fluid Inlet Size (cm): 2.54
- Fluid Inlet Size (in): 1
- Fluid Inlet Size (mm): 25.4
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 1.905
- Fluid Outlet Size (in): 3/4
- Fluid Outlet Size (mm): 19.05
- Fluid Outlet Thread Type: NPT
- Gun Included: 0
- Gun Model: No Applicator
- Gun Technology: Bare Package
- Gun Type: No Applicator
- Hose Inlet Diameter (cm): 0.476
- Hose Inlet Diameter (in): 3/16
- Hose Inlet Diameter (mm): 4.76
- Includes: Pump Only Air Controls
- Maximum Air Inlet Pressure (bar): 7
- Maximum Air Inlet Pressure (kPa): 700
- Maximum Air Inlet Pressure (psi): 100
- Maximum Flow Rate (GPM): 2.4
- Maximum Flow Rate (L/min): 9.0
- Maximum Working Pressure (bar): 103
- Maximum Working Pressure (kPa): 10300
- Maximum Working Pressure (psi): 1500
- Mount Type: Cart Mount
- Power Source: Air
- Pressure Type: High Pressure
- Product Type: Bare Package
- Pump Ratio: 15:1
- Pump Type: Pneumatic Piston Pump