ENERPAC S100272

EP CW142900SR

• Type: ERP

• SubTypes: Repair Part

EP CULP50

CULP-Series Low Height Hydraulic Cylinders, also known as hydraulic pancake cylinders, offer an impressive power to height ratio, making them the right choice for confined spaces where other cylinders will not fit.

There are several configurations to choose from, with tonnage capacities ranging from 10 to 100 imperial tons (97-1077 kN), and collapsed heights from 1.08 - 2.55" (27.5 - 65mm).

All are finished with a tough Nitrocarburized coating for enhanced corrosion protection in harsh working environments.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10150

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: CULP
• Stroke Inches: 0.24
• Stroke MM: 6
• SubTypes: Low Height Cylinder

• Up to 4% side load of maximum capacity
• Stop-ring for maximum stroke limitation
• Extremely low collapsed height
• Nitrocarburized surface treatment for harsh conditions
• Coupler included

• Spare Part(s): CULP50K

EP MMR30K

• Type: Service Kit

EP MPK2

• Type: Service Kit

• SubTypes: Manifold Kit

EP MRS3001

• Type: Hydraulic Cylinders
• Max Bar: 350
• Max PSI: 5000

• Product Group: Cylinders and Jacks
• Product Line: Work Holding Tools
• Series: MRS
• SubTypes: Workholding Positive Clamping Cylinder

• Heavy disk springs maintain the clamping force - hydraulic pressure is used for release
• Single-acting design allows easy setup of hydraulic system
• Hollow plunger design allows easy retrofit for mechanical clamping
• Custom buttons can be fitted into the plunger for clamping directly against a workpiece
• Threaded body allows easy cylinders mounting directly into fixture plate
• Internal threaded plunger allows accessories to be used easily for retrofit applications

• Accessories: BS202

EP MS21020

The MS21020 is our most complete maintenance set that equips you to complete a wide array of maintenance tasks. The assortment of 53 accessories enables you to quickly configure the ideal tool for just about any challenge imaginable.

This set includes three of our most popular hydraulic cylinders: The RC102, RC106, and the RC256. Using these cylinders with attachments will allow you to exert at forces up to 12.5 tons (116kN) and extend up to 6.25" (116mm) - Ideal when you need to push, pull, lift, press, straighten, spread, or clamp.

Also included is the lightweight P392 2-speed hydraulic hand pump, hose, gauge, A92 spreader attachment, lock-on or threaded connectors, and a storage crate.

Safe Operation
When using hydraulic cylinders with maintenance set attachments or components, the maximum system pressure must be limited to half of the rated pressure (5,000 psi / 350 bar). When not using attachments, the tonnage and pressure capacities are double these values.

Only use attachments provided with the set. Using non-Enerpac attachments and longer extension tubes could reduce column strength - potentially creating unsafe conditions.

• Type: Cylinder And PumpSet
• Max Bar: 350
• Max PSI: 5000

• Product Group: Cylinders and Jacks, Pumps
• Product Line: Industrial Tools
• Series: MS
• Stroke Inches: 6.25
• Stroke MM: 158
• SubTypes: Cylinder with Attachments and Hand Pump Set

• Set Includes: P392, HC7206, RC102, RC106, RC256, GP10S, GA2, A13, A28, A21, A27, A20, A595, A14, A243, A10, A8, A6, A192, A305, A18, A185, A15, A607, A129, A128, A132, A238, A5, A141, A218, A19, A242, A92, A16, MZ1050, MZ1051, MZ1052, A285, MZ1002, MZ1003, A239, MZ1004, A240, MZ1005, A241, CW350

EP MS220

This hydraulic pump and cylinder set includes a complete assortment of accessories allowing you to quickly configure a unique tool to solve your many difficult maintenance tasks.

The set includes the RC256 Hydraulic Cylinder, which when used with attachments allows you to exert a force of 12.5 tons (116kN) and a stroke of 6.25" (116mm). Ideal when you need to push, pull, lift, press, straighten, or clamp.

Also included is the lightweight P392 2-speed hydraulic hand pump, hose, gauge, lock-on or threaded connectors, and a storage crate.

Safe Operation
When using hydraulic cylinders with maintenance set attachments or components, the maximum system pressure must be limited to half of the rated pressure (5,000 psi / 350 bar). When not using attachments, the tonnage and pressure capacities are double these values.

Only use attachments provided with the set. Using non-Enerpac attachments and longer extension tubes could reduce column strength - potentially creating unsafe conditions.

• Type: Cylinder And PumpSet
• Max Bar: 350
• Max PSI: 5000

• Product Group: Cylinders and Jacks, Pumps
• Product Line: Industrial Tools
• Series: MS
• Stroke Inches: 6.25
• Stroke MM: 158
• SubTypes: Cylinder with Attachments and Hand Pump Set

• Set Includes: P392, HC7206, RC256, GP10S, GA2, A28, A27, A595, A243, A607, A238, A218, A242, A239, A240, A241, CW166

EP MVK2

• Type: Service Kit

• SubTypes: Repair Kit

EP MVK3

• Type: Service Kit

• SubTypes: Repair Kit

EP MVPM5

• Type: Valve
• Max Bar: 350
• Max PSI: 5000

• Product Group: Valves, Pumps
• Product Line: Work Holding Tools
• Series: MVP
• SubTypes: Sequence Valve

• Sequence valves block the oil to a secondary hydraulic circuit until pressure in the primary circuit reaches a preset level. The sequence valves have a built-in check system to allow the oil to flow back without external piping.
• Direct accurate pressure setting
• Pressure setting between 500-5000 psi for secondary circuit is secured with lock nut
• Manifold mounting ports on MVPM5
• Manifold O-rings included with MVPM5

EP NC2432

NC-Series Hydraulic Nut Splitters use a single blade configuration suited to general nut cutting applications across a wide range of industries.

The heat-treated steel blade with its optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NC-Series Nut Cutters are compact, simple, and easy to use. The ergonomic design ensures comfortable use, thanks to the carefully considered angled head design and handle position.

Nuts are often difficult to remove, and while loosening them using tightening tools is possible, this generally requires larger equipment and takes more time.

Using a cutting torch or a hammer and chisel presents safety risks and can cause damage to the joint components. They also involve significantly longer setup and operational time.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NC
• SubTypes: Nut Cutter

• bundleSet_IDs: NCB2432
• Capacity Imperial Tons: 15
• Capacity KN: 147

• Compact and ergonomic design, easy to use
• Unique angled head design
• Single-acting, spring return cylinder
• Heavy duty chisels can be reground
• Nut Splitters include spare chisel, spare set screw and wrench used to secure the chisel. A CR-400 coupler is standard.
• For applications with bolt sizes that are common to two tool model sizes, we recommend to select the larger of the two tools for the best results.
• These are not suited for square, star, round or stainless steel nuts. Maximum allowable hardness of nuts to be split is HRc-44.
• For materials and sizes not specified, contact Enerpac Technical Services.

• Accessories: NCB2432

EP NC3241

NC-Series Hydraulic Nut Splitters use a single blade configuration suited to general nut cutting applications across a wide range of industries.

The heat-treated steel blade with its optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NC-Series Nut Cutters are compact, simple, and easy to use. The ergonomic design ensures comfortable use, thanks to the carefully considered angled head design and handle position.

Nuts are often difficult to remove, and while loosening them using tightening tools is possible, this generally requires larger equipment and takes more time.

Using a cutting torch or a hammer and chisel presents safety risks and can cause damage to the joint components. They also involve significantly longer setup and operational time.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NC
• SubTypes: Nut Cutter

• Capacity Imperial Tons: 20
• Capacity KN: 196

• Compact and ergonomic design, easy to use
• Unique angled head design
• Single-acting, spring return cylinder
• Heavy duty chisels can be reground
• Nut Splitters include spare chisel, spare set screw and wrench used to secure the chisel. A CR-400 coupler is standard.
• For applications with bolt sizes that are common to two tool model sizes, we recommend to select the larger of the two tools for the best results.
• These are not suited for square, star, round or stainless steel nuts. Maximum allowable hardness of nuts to be split is HRc-44.
• For materials and sizes not specified, contact Enerpac Technical Services.

• Accessories: NCB3241

EP NC4150

NC-Series Hydraulic Nut Splitters use a single blade configuration suited to general nut cutting applications across a wide range of industries.

The heat-treated steel blade with its optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NC-Series Nut Cutters are compact, simple, and easy to use. The ergonomic design ensures comfortable use, thanks to the carefully considered angled head design and handle position.

Nuts are often difficult to remove, and while loosening them using tightening tools is possible, this generally requires larger equipment and takes more time.

Using a cutting torch or a hammer and chisel presents safety risks and can cause damage to the joint components. They also involve significantly longer setup and operational time.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NC
• SubTypes: Nut Cutter

• bundleSet_IDs: NCB4150
• Capacity Imperial Tons: 35
• Capacity KN: 343

• Compact and ergonomic design, easy to use
• Unique angled head design
• Single-acting, spring return cylinder
• Heavy duty chisels can be reground
• Nut Splitters include spare chisel, spare set screw and wrench used to secure the chisel. A CR-400 coupler is standard.
• For applications with bolt sizes that are common to two tool model sizes, we recommend to select the larger of the two tools for the best results.
• These are not suited for square, star, round or stainless steel nuts. Maximum allowable hardness of nuts to be split is HRc-44.
• For materials and sizes not specified, contact Enerpac Technical Services.

• Accessories: NCB4150

EP NC6075

NC-Series Hydraulic Nut Splitters use a single blade configuration suited to general nut cutting applications across a wide range of industries.

The heat-treated steel blade with its optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NC-Series Nut Cutters are compact, simple, and easy to use. The ergonomic design ensures comfortable use, thanks to the carefully considered angled head design and handle position.

Nuts are often difficult to remove, and while loosening them using tightening tools is possible, this generally requires larger equipment and takes more time.

Using a cutting torch or a hammer and chisel presents safety risks and can cause damage to the joint components. They also involve significantly longer setup and operational time.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NC
• SubTypes: Nut Cutter

• Capacity Imperial Tons: 90
• Capacity KN: 882

• Compact and ergonomic design, easy to use
• Unique angled head design
• Single-acting, spring return cylinder
• Heavy duty chisels can be reground
• Nut Splitters include spare chisel, spare set screw and wrench used to secure the chisel. A CR-400 coupler is standard.
• For applications with bolt sizes that are common to two tool model sizes, we recommend to select the larger of the two tools for the best results.
• These are not suited for square, star, round or stainless steel nuts. Maximum allowable hardness of nuts to be split is HRc-44.
• For materials and sizes not specified, contact Enerpac Technical Services.

• Accessories: NCB6075

EP NCB1924

• Type: Cutter Accessory

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NCB
• SubTypes: Replacement Chisel

EP NCB2432

• Type: Cutter Accessory

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NCB
• SubTypes: Replacement Chisel

EP NCB3241

• Type: Cutter Accessory

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NCB
• SubTypes: Replacement Chisel

EP NCB4150

• Type: Cutter Accessory

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NCB
• SubTypes: Replacement Chisel

EP NSH1927

NSH-Series Hydraulic Nut Splitters are suited to flange nut splitting jobs in the oil and gas industries.

The heat-treated steel blade with optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NSH-Series Nut Cutters are simple and easy to use. They include an ergonomically designed revolving handle for comfortable working and to isolate shock and vibration. The supplied lanyard and revolving anchor point are drop tested to ensure safety.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NSH
• SubTypes: Nut Splitter

• Capacity Imperial Tons: 12
• Capacity KN: 120

• Quick and easy cutting tip replacement
• Drop-tested revolving anchor point and safety lanyard
• Revolving composite handle for vibration and shock isolation
• Nut Splitters include set of hexagon keys and following spare parts:
  - cutting tip
  - tip retention screw
  - spare alignment screw
• Standard Safety Lanyard with each nut splitter. Includes steel cable with carabiners.
• CR400 female half coupler is standard
• Maximum allowable hardness to split is ASTM A194 Gr 2H. Not to be used on square nuts or stainless steel.

• Set Includes: CR400, FSC1
• Accessories: NSH1927CTK

EP P141K2

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P142ALSS

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P
• SubTypes: Hand Pump - Two Speed

• Corrosion resistant, nickel-plated valves and cylinders
• Stainless steel pump inserts will not corrode
• Viton Seals provide heat and chemical resistance
• Anodized aluminum pump reservoirs and plastic encapsulated pump bodies resist wet environments
• Two-speed operation reduces pump handle strokes 78% compared to single-speed pumps
• Pump handles lock for easy carrying

• Spare Part(s): DA8802900SR, P142ALSSK

EP P202K1

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P181190W

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Relief Valve

EP P20857

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Crosspin

EP P25

These Low-Pressure Hydraulic Hand Pumps are durable, portable, highly efficient, and easy to use. Each model in the series features an all-steel construction, a chrome plated plunger, and a wiper system for long-lasting performance.

These pumps are constructed to power a wide range of single acting cylinders and tools in space restricted areas. The range includes the P51 that can be operated in the horizontal orientation only, and others also capable of operating in the vertical orientations: P18 with the pump head facing down, P25, P50 with the pump head facing up. Each is protected by external load-release valves and internal overload pressure-relief valves.

With a choice of oil capacities up to 200 in3 (3,277 cm3), and operating pressures of 2,500 psi (175 bar) - 5,000 psi (350 bar) you will find an Enerpac Low Pressure Hydraulic Hand Pump to suit your needs.

• Type: Hydraulic Pump
• Max Bar: 175
• Max PSI: 2500

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P
• SubTypes: Hand Pump - Single Speed

• P25 and P50 pumps oil in both forward and reverse handle movement improving overall efficiency, ideal when mounting space is restricted
• External load-release valve
• Internal pressure-relief valve for overload protection
• P25 and P50 vertical operation requires pump vent side facing up

• Spare Part(s): CA365024SR, P181190W, P50K1

EP P391K2

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P30718

• Type: Service Kit

• SubTypes: Repair Part

EP P301D

• Heavy duty, metal construction for durability.
• High displacements of oil per stroke.
• Low, back saving handle effort.
• Large reservoir capacities.

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: P Steel
• SubTypes: Hand Pump - Heavy Duty Steel

EP P392E024K

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P39K4

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P84K3

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P84HDK

• Type: Service Kit

• SubTypes: Handle

EP P39K5

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P45138

• Type: Service Kit

• SubTypes: Screw

EP P77K1

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P39RVK

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Valve Assembly

EP P84VRK

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Valve Assembly

EP PA1065040

• Type: Component

EP P50K1

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P (Service Kit)
• SubTypes: Repair Kit

EP P6012SR

• Type: Service Kit

• SubTypes: Repair Part

EP P6010

• Type: Service Kit

• SubTypes: Spindle Repair Kit

EP P75181

• Type: Service Kit

• SubTypes: Nut

EP P80K8

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P60234-1SR

• Type: Service Kit

• SubTypes: Repair Part

EP P6012

• Type: Service Kit

• SubTypes: Repair Part

EP P51K1

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P (Service Kit)
• SubTypes: Repair Kit

EP P80K4

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P45139

• Type: Service Kit

• SubTypes: Washer

EP P51

These Low-Pressure Hydraulic Hand Pumps are durable, portable, highly efficient, and easy to use. Each model in the series features an all-steel construction, a chrome plated plunger, and a wiper system for long-lasting performance.

These pumps are constructed to power a wide range of single acting cylinders and tools in space restricted areas. The range includes the P51 that can be operated in the horizontal orientation only, and others also capable of operating in the vertical orientations: P18 with the pump head facing down, P25, P50 with the pump head facing up. Each is protected by external load-release valves and internal overload pressure-relief valves.

With a choice of oil capacities up to 200 in3 (3,277 cm3), and operating pressures of 2,500 psi (175 bar) - 5,000 psi (350 bar) you will find an Enerpac Low Pressure Hydraulic Hand Pump to suit your needs.

• Type: Hydraulic Pump
• Max Bar: 200
• Max PSI: 3000

• Product Group: Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: P
• SubTypes: Hand Pump - Single Speed

• External load-release valve
• Internal pressure-relief valve for overload protection
• P51 for horizontal operation only

• Spare Part(s): CJ589950W, P181190W, P51K1

EP P6011

• Type: Service Kit

• SubTypes: Nut

EP P80SFK

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Valve Repair Kit

EP P75266-1

• Type: Service Kit

• SubTypes: Reservoir Assembly

EP P464

Ultima Steel Hand Pumps are durable, portable, and highly efficient. Each model in the series features an all-steel construction, a chrome plated plunger, and a wiper system for long-lasting performance.

All except the P39 are 2 stage pumps, which reduces the number of handle strokes by as much as 78% compared to a single speed pump. This is ideal for applications when high flow is needed at the first stage, (such as when advancing a cylinder to the point of load contact). The pump switches automatically to the second stage which is the low flow high-pressure stage.

With a choice of oil capacities up to 453 in3 (7423 cm3), you will find Ultima Steel Hand Pumps that can handle multiple cylinder hook-ups, including models to suit either single-acting and double-acting cylinders.

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P
• SubTypes: Hand Pump - Two Speed

• Reduced handle effort and ergonomic grip for less operator fatigue
• Vent free reservoir eliminates spills
• Quick grip handle allows for easy transport
• Integral reservoir over-pressurization protection

• Spare Part(s): P462K2, P462K3

EP P462K3

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P (Service Kit)
• SubTypes: Repair Kit

EP PA133K3

• Type: Service Kit

• Product Group: Pumps
• SubTypes: Repair Kit

EP PACG30S8SWM10

Enerpac PACG Air Hydraulic Pumps are for designed for intermittent to medium duty workholding applications up to 5,000 psi. Valve mount options include, remote, and mountings for DO3 and VP valves.

Enerpac Turbo II Air Over Hydraulic Pumps generate the hydraulic pressure you need using the air pressure you have available. The Air Saver Piston reduces air consumption, and the pump can start at low pressures from 50-125 psi.

Turbo II Air-Hydraulic Pumps are best suited to medium or lower cycle applications. They provide the power and speed needed for simple clamping circuits and mostly single acting tools. At only 75 dBA, the Turbo II Series helps to keep the noise level to a minimum.

Choose from a range with maximum working pressure of either 5,000 or 10,000psi, and various reservoir capacities from 116 - 462 in3 (2100 - 7500 cm3).

Turbo II Air Over Hydraulic Pump Series :

• PATG - Treadle for foot or hand operation
• PARG - Pendant Operation
• PAMG - Manual lever operated. For double-acting applications
• PACG - For remote valve mount. For workholding, 5000 psi (350 bar).
• PASG - Includes mount for a single DO3 Valve. For workholding, 5000 psi (350 bar).

• Type: Hydraulic Pump
• Max Bar: 350
• Max PSI: 5000

• Product Group: Pumps
• Product Line: Work Holding Tools
• Series: PACG
• SubTypes: Air Pump

• On-demand stall-restart operation maintains system pressure, providing clamping security
• External adjustable pressure relief valve (behind sight glass)
• Internal pressure relief valve provides overload protection
• Reduced noise level to 75 dBA
• Operating air pressure: 50-125 psi - enables pump to start at low air pressure**
• Hydraulic to air ratio: 45:1
• Reinforced heavy-duty lightweight reservoir for applications in tough environments
• Five valve mounting options provide flexibility in setup and operation
• Fully serviceable air motor assembly
• User supplied valves

** NOTE: From 50-125 psi air inlet pressure. Performance is significantly diminished below 50 psi. Performance may vary compared to listed values due to seal friction, internal pressure drops and manufacturing tolerances. Be sure to allow some flexibility on air inlet pressure.

EP PACG5002SB

Enerpac PACG Air Hydraulic Pumps are for designed for intermittent to medium duty workholding applications up to 5,000 psi. Valve mount options include, remote, and mountings for DO3 and VP valves.

Enerpac Turbo II Air Over Hydraulic Pumps generate the hydraulic pressure you need using the air pressure you have available. The Air Saver Piston reduces air consumption, and the pump can start at low pressures from 50-125 psi.

Turbo II Air-Hydraulic Pumps are best suited to medium or lower cycle applications. They provide the power and speed needed for simple clamping circuits and mostly single acting tools. At only 75 dBA, the Turbo II Series helps to keep the noise level to a minimum.

Choose from a range with maximum working pressure of either 5,000 or 10,000psi, and various reservoir capacities from 116 - 462 in3 (2100 - 7500 cm3).

Turbo II Air Over Hydraulic Pump Series :

• PATG - Treadle for foot or hand operation
• PARG - Pendant Operation
• PAMG - Manual lever operated. For double-acting applications
• PACG - For remote valve mount. For workholding, 5000 psi (350 bar).
• PASG - Includes mount for a single DO3 Valve. For workholding, 5000 psi (350 bar).

• Type: Hydraulic Pump
• Max Bar: 350
• Max PSI: 5000

• Product Group: Pumps
• Product Line: Work Holding Tools
• Series: PACG
• SubTypes: Air Pump

• On-demand stall-restart operation maintains system pressure, providing clamping security
• External adjustable pressure relief valve (behind sight glass)
• Internal pressure relief valve provides overload protection
• Reduced noise level to 75 dBA
• Operating air pressure: 50-125 psi - enables pump to start at low air pressure**
• Hydraulic to air ratio: 45:1
• Reinforced heavy-duty lightweight reservoir for applications in tough environments
• Five valve mounting options provide flexibility in setup and operation
• Fully serviceable air motor assembly
• User supplied valves

** NOTE: From 50-125 psi air inlet pressure. Performance is significantly diminished below 50 psi. Performance may vary compared to listed values due to seal friction, internal pressure drops and manufacturing tolerances. Be sure to allow some flexibility on air inlet pressure.

EP ST102A

• Type: Cylinder And PumpSet
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: ST - Simplex
• Stroke Inches: 2.19
• Stroke MM: 55.6
• SubTypes: Steel General Purpose Cylinder and Steel Hand Pump Set

• Capacity Imperial Tons: 10
• Capacity KN: 89,0

• Set Includes: R102, P42, HCA6, GT5, GA1-Simplex

EP SRS15X

• Type: Service Kit

EP STF14H

• Type: Spreader
• Max Bar: 700
• Max PSI: 10000

• Product Group: Flange Maintenance Tools
• Product Line: Industrial Tools, Bolting Tools
• Series: STF
• SubTypes: Hydraulic Spreader Kit

• Capacity Imperial Tons: 14

• Set Includes: FSH14, P392, HC7206, GA2, GP10S

EP SS202K

• Type: Service Kit

EP STLD51

• Type: Work Holding Clamp
• Max PSI: 5000
• Min PSI: 500

• Product Group: Workholding Tools
• Product Line: Work Holding Tools
• Series: ST
• Stroke Inches: 0.89
• SubTypes: Swing Clamp - Threaded Body

• Body thread for precise cylinder height positioning
• Threaded port connection
• Easy installation and removal
• Greatest flexibility in fixture design
• 30, 45 and 60 degree swing angles available on request
• Enerpac threaded body swing clamps are threaded directly into the fixture.
• The cylinder height is adjusted to the appropriate height, and then locked in place using a jam nut

EP ST556A

• Type: Cylinder And PumpSet
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: ST - Simplex
• Stroke Inches: 6.19
• Stroke MM: 157.2
• SubTypes: Steel General Purpose Cylinder and Steel Hand Pump Set

• Capacity Imperial Tons: 55
• Capacity KN: 489,3

• Set Includes: R556, P82, HCA6, GT25, GA1-Simplex

EP SULS201

• Type: Work Holding Clamp
• Max PSI: 5000
• Min PSI: 500

• Product Group: Workholding Tools
• Product Line: Work Holding Tools
• Series: SU
• Stroke Inches: 1.16
• SubTypes: Swing Clamp - Upper Flange

• Flexible design allows for manifold or threaded port connection
• Low profile mounting style allows body to be below mounting surface
• Simple mounting preparation and easy installation - 3 or 4 mounting bolts
• Double oil connection - threaded port or manifold mount
• Symmetrical rectangular flange design enables clamping at three sides of the cylinder
• 30, 45, and 60 degree swing angles available on request
• The Enerpac upper flange swing clamps are designed for integrated manifold mounting solutions. Hydraulic connections are made through SAE or BSPP oil connection or the standard integrated O-ring ports.

EP STN1924H

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: STN
• SubTypes: Nut Cutter Set

• Capacity Imperial Tons: 10
• Capacity KN: 98

• Compact and ergonomic design, easy to use
• Unique angled head allows flush access
• Single-acting, spring return cylinder
• Heavy-duty chisels can be reground
• Applications include servicing trucks, piping industry, tank cleaning, petrochemical, steel construction and mining

• Set Includes: NC1924, P392, CR400
• Accessories: NCB1924

EP SURS201

• Type: Work Holding Clamp
• Max PSI: 5000
• Min PSI: 500

• Product Group: Workholding Tools
• Product Line: Work Holding Tools
• Series: SU
• Stroke Inches: 1.16
• SubTypes: Swing Clamp - Upper Flange

• Flexible design allows for manifold or threaded port connection
• Low profile mounting style allows body to be below mounting surface
• Simple mounting preparation and easy installation - 3 or 4 mounting bolts
• Double oil connection - threaded port or manifold mount
• Symmetrical rectangular flange design enables clamping at three sides of the cylinder
• 30, 45, and 60 degree swing angles available on request
• The Enerpac upper flange swing clamps are designed for integrated manifold mounting solutions. Hydraulic connections are made through SAE or BSPP oil connection or the standard integrated O-ring ports.

EP SURD201

• Type: Work Holding Clamp
• Max PSI: 5000
• Min PSI: 500

• Product Group: Workholding Tools
• Product Line: Work Holding Tools
• Series: SU
• Stroke Inches: 1.16
• SubTypes: Swing Clamp - Upper Flange

• Flexible design allows for manifold or threaded port connection
• Low profile mounting style allows body to be below mounting surface
• Simple mounting preparation and easy installation - 3 or 4 mounting bolts
• Double oil connection - threaded port or manifold mount
• Symmetrical rectangular flange design enables clamping at three sides of the cylinder
• 30, 45, and 60 degree swing angles available on request
• The Enerpac upper flange swing clamps are designed for integrated manifold mounting solutions. Hydraulic connections are made through SAE or BSPP oil connection or the standard integrated O-ring ports.

EP SWi1214TMSTDEX

The Equalizer SWi1214TMSTDEX Mechanical Flange Spreader is manually operated and does not need an external hydraulic pump and trailing hoses - ideal for working in difficult spaces at remote locations.

It is ATEX certified, which means it has gone through rigorous testing outlined by European Union directives, and proven to be safe for use in specific environments with explosive atmospheres.

The spreader in the SWi1214TMSTDEX set fits into very small clearance gaps of 0.24 inch (6 mm).

• Type: Spreader
• Max PSI: 10000

• Product Group: Flange Maintenance Tools
• Product Line: Bolting Tools
• Series: SWi
• SubTypes: Flange Spreader Set - Wedges

• Capacity Imperial Tons: 15.7
• Capacity KN: 140
• Capacity Metric Tons: 14

Set Includes

• 1 x SWi12/14TMEX Mechanical Flange Spreader Wedgehead
• 1 x 12/14TMEX Mechanical Cylinder
• 1 x Torque Wrench with 22 mm Socket
• 1 x Set of Safety Blocks
• 1 x Pair of Stepped Blocks
• 1 x Safety Lanyard
• 1 x Hex Key
• 1 x Instruction Manual
• 1 x Carry Case, Case Dimensions: 580 mm x 400 mm x 180 mm

User Features

• Certified for use in the hazardous areas:
• II 2G ck IIB T6/II 2D ck T85 degrees C
• Practical, portable and lightweight
• Molded plastic handle for comfort
• Revolving handle to aid horizontal or vertical spreading
• Offset handle is directly over the center of mass
• Removable handle for improved access
• Revolving lanyard connection point
• Spread indicator markings for clear precise visual progress feedback

Safety Features

• No finger pinch-points
• Increased step depth on upper steps
• Safety lanyard - 1.0 m (39" ) length
• Forged key components for strength and reliability
• Maintenance Features
• Rapid disassembly and assembly
• Quick jaw replacement - remove 1 fastener
• Quick tip replacement - remove 2 fasteners
• Narrow jaw teeth - improved tool wear

ATEX Certified

• II 2G Ex h IIB T6 Gb
• II 2D Ex h IIIC T85 degrees C

EP SWi2025TEMINSPB

The Equalizer SWi2025TEMINSPB Mini Set includes a flange spreader wedgehead, hydraulic cylinder, safety block, stepped block, lanyard, and carry case.

Within the spreader sits an integral hydraulic cylinder, which when used with a separate hydraulic pump (not supplied), makes it easy to exert a powerful force for separating pipe flanges.

• Type: Spreader
• Max Bar: 700
• Max PSI: 10000

• Product Group: Flange Maintenance Tools
• Product Line: Bolting Tools
• Series: SWi
• SubTypes: Flange Spreader Set - Wedges

• Capacity Imperial Tons: 27
• Capacity KN: 240
• Capacity Metric Tons: 24

Mini Set Includes

• 1 x SWi20/25TE Flange Spreader Wedgehead
• 1 x 10,000 psi Hydraulic Cylinder
• 1 x Safety Block
• 1 x Lanyard
• Case dimensions (in) 36.2 x 19.7 x 8.1

User Features

• Practical, portable and lightweight
• Molded plastic handle for comfort
• Revolving handle to aid horizontal or vertical spreading
• Removable handle for improved access

Safety Features

• No finger pinch-points
• Increased step depth on upper steps
• Safety lanyard - 39 inches (1 m) length
• Forged key components for strength and reliability

Maintenance Features

• Rapid disassembly and assembly
• Narrow jaw teeth - improved tool wear

EP SWi5TE-S

This Equalizer set includes a flange spreader wedgehead, hydraulic cylinder, safety block, stepped block, lanyard, and carry case.

Within the spreader sits an integral hydraulic cylinder, which when used with a separate hydraulic pump (not supplied), makes it easy to exert a powerful force for separating pipe flanges.

• Type: Spreader
• Max Bar: 700
• Max PSI: 10000

• Product Group: Flange Maintenance Tools
• Product Line: Bolting Tools
• Series: SWi
• SubTypes: Flange Spreader Set - Wedges

• Capacity Imperial Tons: 8.7
• Capacity KN: 77
• Capacity Metric Tons: 7.7

• 1 x SWi5TE Flange Spreader Wedgehead
• 1 x 10,000 psi Hydraulic Cylinder
• 1 x Safety Block
• 1 x Lanyard
• Case dimensions (in) 22.8 x 13.4 x 7.1

• Practical, portable and lightweight
• Molded plastic handle for comfort
• Revolving handle to aid horizontal or vertical spreading
• Removable handle for improved access

• No finger pinch-points
• Increased step depth on upper steps
• Safety lanyard - 39 inches (1 m) length
• Forged key components for strength and reliability

• Rapid disassembly and assembly
• Narrow jaw teeth - improved tool wear

• Accessories: 1640016-01

EP T6003L

These dry high-pressure testing gauges feature a large diameter face for easy readability and dual scales of psi and bar. An integral maximum indicator pointer is included as standard.

Choose a T-Series high pressure gauge from range with maximum working pressures ranging from 1,000 up to 50,000 psi (70 to 3500 bar). All gauge cases are manufactured from tough grades of steel, which depending on the model, will be high alloy steel, 316 stainless steel or 401 stainless steel. All gauges have spring-loaded backs with rubber blow-out plugs to protect the case assembly in case of over-pressurization.

Gauges models up to 20,000 psi (1400 bar) are accurate to within +/- 0.5%, and models to 50,000 psi (3500 bar) to within +/- 1.5%.

• Type: Gauge
• Max Bar: 700
• Max PSI: 10000

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools
• Series: T - Gauge
• SubTypes: Pressure Gauge

• Calibrated in dual scale reading in psi and bar
• All pressure sensing parts sealed and dampened by glycerine for long life
• Includes safety blow-out disk and pressure equalizing membrane
• Gauge snubbers or needle valves recommended for high cycle applications

EP TJH109LS

• Self-contained models for maximum versatility.
• Low toe heights fit in tight clearances.
• The lowest handle effort for easy operation.
• TJH109LS comes equipped with an ergonomic pistol grip for rapid advancement to load.
• The lowest weights for reduced back injuries.
• Lever Bars are included with all models.
• TJH109LS Toe Jack comes equipped with a solid one piece Lever Bar.
• Toe Lifts are rated at maximum capacity on all models.

• Type: Jack

• Product Line: Hydraulic Tools
• Series: TJH
• Stroke Inches: 9
• Stroke MM: 228.6
• SubTypes: Heavy Duty Toe Jacks

• Capacity Imperial Tons: 10
• Capacity KN: 89

EP TH630

• Type: Coupler
• Max Bar: 700
• Max PSI: 10000

• Product Group: Couplers
• Product Line: Industrial Tools
• Series: TH
• SubTypes: Spin-on Coupler

• Enerpac hydraulic couplers provide quick connection of hydraulic lines
• 10,000 and 11,600 psi 1/4" couplers for torque wrenches
• 10,000 psi 3/8" couplers for cylinders, tools and pumps
• Dimension A is total length when male and female halves are connected.

EP TJH10A

• Self-contained models for maximum versatility.
• Low toe heights fit in tight clearances.
• The lowest handle effort for easy operation.
• The lowest weights for reduced back injuries.
• Swivel sockets for access in close quarters. (TJH5A & TJH10A only).
• Lever Bars are included with all models.
• TJH2A, TJH5A and TJH10A Toe Jacks come equipped with a 3 piece Lever Bar set to accommodate space limitations.
• Toe Lifts are rated at maximum capacity on all models.

• Type: Jack

• Product Line: Hydraulic Tools
• Series: TJH
• Stroke Inches: 5.71
• Stroke MM: 149.1
• SubTypes: Heavy Duty Toe Jacks

• Capacity Imperial Tons: 10
• Capacity KN: 89

EP TJH109LSRK

• Type: Service Kit

• Series: TJH

EP TJH5A

• Self-contained models for maximum versatility.
• Low toe heights fit in tight clearances.
• The lowest handle effort for easy operation.
• The lowest weights for reduced back injuries.
• Swivel sockets for access in close quarters. (TJH5A & TJH10A only).
• Lever Bars are included with all models.
• TJH2A, TJH5A and TJH10A Toe Jacks come equipped with a 3 piece Lever Bar set to accommodate space limitations.
• Toe Lifts are rated at maximum capacity on all models.

• Type: Jack

• Product Line: Hydraulic Tools
• Series: TJH
• Stroke Inches: 4.73
• Stroke MM: 117.3
• SubTypes: Heavy Duty Toe Jacks

• Capacity Imperial Tons: 5
• Capacity KN: 44,5

EP TJHAK10

• Type: Service Kit

• Series: TJH

EP TJHAS10

• Type: Service Kit

• Series: TJH

EP TJHAK101

• Type: Service Kit

• Series: TJH

EP TJHRH10

• Type: Service Kit

• Series: TJH

EP TR630

• Type: Coupler
• Max Bar: 700
• Max PSI: 10000

• Product Group: Couplers
• Product Line: Industrial Tools
• Series: TR - Coupler
• SubTypes: Spin-on Coupler

• Enerpac hydraulic couplers provide quick connection of hydraulic lines
• 10,000 and 11,600 psi 1/4" couplers for torque wrenches
• 10,000 psi 3/8" couplers for cylinders, tools and pumps
• Dimension A is total length when male and female halves are connected.

EP TRCM2006

• Type: Hydraulic Cylinders
• Max Bar: 350
• Max PSI: 5000

• Product Group: Cylinders and Jacks
• Product Line: Work Holding Tools
• Series: TR
• Stroke Inches: 6
• Stroke MM: 152.4
• SubTypes: Tie Rod Cylinder

• Clevis mount cylinders include pivot pin for mounting in your machine
• Standard rod eyes and rod clevises available for each bore size.
• NFPA style MP1
• Designed to carry shear loads
• Pivot pins should be carried by rigidly held bearings and closely fit for the entire length of the pin

EP TRCM2504

• Type: Hydraulic Cylinders
• Max Bar: 350
• Max PSI: 5000

• Product Group: Cylinders and Jacks
• Product Line: Work Holding Tools
• Series: TR
• Stroke Inches: 4
• Stroke MM: 101.6
• SubTypes: Tie Rod Cylinder

• Clevis mount cylinders include pivot pin for mounting in your machine
• Standard rod eyes and rod clevises available for each bore size.
• NFPA style MP1
• Designed to carry shear loads
• Pivot pins should be carried by rigidly held bearings and closely fit for the entire length of the pin

EP V152

The V152 and V152VN adjustable hydraulic pressure relief valves are used to limit hydraulic pressure and regulate oil flow.

Easy adjustment is done by simply turning the handle clockwise to increase the pressure. The valves offer repeatability accuracy of ±

EP V10

The V10 Auto-Damper Valve will protect a pressure gauge during high cycle applications. It does this by creating a flow resistance if a load is released suddenly.

It may be used to automate clamp cycles, prevent pressure loss, and provide additional operator and component safety. No adjustment is necessary, and the valve simply connects to GA1, GA2 or GA4 gauge adaptors with ½" NPTF male and female threads.

• Type: Valve
• Max Bar: 700
• Max PSI: 10000

• Product Group: Valves, Pumps
• Product Line: Work Holding Tools
• Series: V
• SubTypes: Auto-damper Valve

• To protect gauge during high cycle applications
• Creates a flow resistance when load is released suddenly No adjustments are necessary
• Fits directly into GA-series gauge adaptor
• Used to automate clamp cycles, prevent pressure loss and provide additional operator and component safety
• Regulate oil flow or system pressure
• All valves feature NPT or SAE porting to insure against leakage at rated pressure
• Can easily be installed in any system
• All valves are painted, coated or plated for corrosion resistance

EP V152NV

The V152 and V152VN adjustable hydraulic pressure relief valves are used to limit hydraulic pressure and regulate oil flow.

Easy adjustment is done by simply turning the handle clockwise to increase the pressure. The valves offer repeatability accuracy of ±3% and an adjustment range of 800-10,000 psi (55-700 bar).

The maximum oil flow is 1830 in3 /min (30 l/min) and the valve features NPT or SAE porting to insure against leakage at rated pressure. A 3 ft return line hose kit is included.

The V152NV Nickel plated model option provides enhanced resistance to corrosion. Viton seals in V66NV and V152NV for high temperature applications.

• Type: Valve
• Max Bar: 700
• Max PSI: 10000

• Product Group: Valves, Pumps
• Product Line: Industrial Tools
• Series: V
• SubTypes: Pressure Relief Valve

• Corrosion resistant, nickel-plated valves
• Viton Seals provide heat and chemical resistance
• Used to automate clamp cycles, prevent pressure loss and provide additional operator and component safety
• Regulate oil flow or system pressure
• All valves feature NPT or SAE porting to insure against leakage at rated pressure
• Can easily be installed in any system

EP V42K

• Type: ERP

• SubTypes: Repair Part

EP V152K

• Type: Service Kit

• SubTypes: Repair Kit

EP V82K

• Type: Service Kit

• SubTypes: Repair Part

EP VC4

• Type: Valve
• Max Bar: 700
• Max PSI: 10000

• Product Group: Valves, Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: VC
• SubTypes: Directional Control Valve

• Advance/Hold/Retract operation for use with single-acting cylinders.
• For applications that require positive load holding, VC and VM Series valves are available with a pilotoperated check valve. This option provides hydraulic locking of the load until the valve is shifted into the retract position.

EP VD1P

• Type: Valve
• Max Bar: 350
• Max PSI: 5000

• Product Group: Valves, Pumps
• Product Line: Work Holding Tools
• Series: VD
• SubTypes: Check Valve

EP VE32D

• Type: Valve
• Max Bar: 700
• Max PSI: 10000

• Product Group: Valves, Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: VE
• SubTypes: Directional Control Valve

• Advance/Hold/Retract operation of single-acting cylinders
• Solenoid Operation
• Pump mounting will retrofit on most Enerpac Pumps
• User adjustable relief valves allow the operator to easily set the working pressure

EP VE32

• Type: Valve
• Max Bar: 700
• Max PSI: 10000

• Product Group: Valves, Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: VE
• SubTypes: Directional Control Valve

• Advance/Hold/Retract operation of single-acting cylinders
• Solenoid Operation
• Pump mounting will retrofit on most Enerpac Pumps
• User adjustable relief valves allow the operator to easily set the working pressure

EP VE43K1

• Type: Service Kit

• SubTypes: Repair Kit

EP VE33

• Type: Valve
• Max Bar: 700
• Max PSI: 10000

• Product Group: Valves, Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: VE
• SubTypes: Directional Control Valve

• Advance/Hold/Retract operation of single-acting cylinders
• Solenoid Operation
• Pump mounting will retrofit on most Enerpac Pumps
• Standard " locking" feature on VE Series 3-position valves
• User adjustable relief valves allow the operator to easily set the working pressure

EP VEB15600B

• Type: Valve

• Product Group: Valves, Pumps

EP VEB11600B

• Type: Valve

• Product Group: Valves, Pumps

EP VFC3

• Type: Valve
• Max Bar: 350
• Max PSI: 5000

• Product Group: Valves, Pumps
• Product Line: Work Holding Tools
• Series: VFC
• SubTypes: Flow Control Valve

• Poppet valve design for zero leakage
• Color coded flow indicator
• Free flow return
• Fine metering capability
• Lockable
• Standard Viton seals

EP VLP106P142U

• Type: Hydraulic Press
• Max Bar: 700
• Max PSI: 10000

• Product Group: Presses
• Product Line: Industrial Tools
• Series: VLP
• SubTypes: Bench Press

• Capacity Imperial Tons: 10
• Capacity KN: 101

• The VLP-Series Presses provide a simple and economical solution for standard workshop applications. Compact and versatile, it's the ideal solution for pressing smaller workpieces from the comfort of a workbench.
• Compact design mounts conveniently on bench top
• Operational in vertical or horizontal position

• Set Includes: RC106, P142, GF10P, HC7206
• Accessories: VB10

EP VM22K

• Type: Service Kit

• SubTypes: Repair Kit