ENERPAC S100272

EP PARG1105N

Enerpac Turbo II Air Over Hydraulic Pumps generate the hydraulic pressure you need using the air pressure you have available. The Air Saver Piston reduces air consumption, and the pump can start at low pressures from 50-125 psi.

Turbo II Air-Hydraulic Pumps are best suited to medium or lower cycle applications. They provide all the power and speed needed for simple clamping circuits and mostly single acting tools. At only 75 dBA, the Turbo II Series helps to keep the noise level to a minimum.

Choose from a range with maximum working pressure of either 5,000 or 10,000psi, and various reservoir capacities from 116 - 462 in3 (2100 - 7500 cm3).

Each PARG pump variant includes a 3-way, 3-position valve for Advance / Hold / Retract functions.

Turbo II Air Over Hydraulic Pump Series :

• PATG - Treadle for foot or hand operation
• PARG - Pendant Operation
• PAMG - Manual lever operated. For double-acting applications
• PACG - For remote valve mount. For work holding, 5000 psi (350 bar).
• PASG - Includes mount for a single DO3 Valve.

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: PARG
• SubTypes: Air Pump

• High efficiency cast aluminum air motor for increased life and reduced air consumption
• Reinforced heavy-duty reservoir for applications in tough environments
• New generation air saver piston with rugged one-piece design reduces air consumption and operating costs
• Return-to-tank port for use in remote valve applications
• Quiet - only 76dBA with low air consumption of 12 scfm
• Operating air pressure: 40-125 psi, enables pump to start at extremely low pressure
• Internal pressure relief valve provides overload protection

EP PE10000SR

• Type: ERP

• SubTypes: Repair Part

EP PJ3P

• Side locking screw keeps the jack extended and prevents lowering due to vibration.
• Screw operation provides countless adjustments for exact leveling.
• Ideal jack for leveling plane beds, millers and machinery.
• Ball and socket cap swivels to center load forces.
• Notched base fastens easily to machine beds.
• CE Compliant - Our Jack design specifications meet or exceed ANSI /ASME B30.1 Safety Standards.
• Slotted load cap prevents the load from possible slippage with inline applications.

• Type: Jack

• Product Line: Mechanical Tools
• Series: PJ
• Stroke Inches: 2.25
• Stroke MM: 57.2
• SubTypes: Planer Jack

• Capacity Imperial Tons: 6
• Capacity KN: 53,4

EP PMB2

• Type: Press Accessory

• Product Group: Presses
• Product Line: Industrial Tools
• Series: A
• SubTypes: Press Pump Mounting Bracket

• Heavy duty steel brackets to allow conversion to one of the Enerpac Power Sources to power your press.
• Both mounting brackets are pre-drilled to accept a number of different pump models

EP PME10427K

• Type: Service Kit

• Product Group: Pumps
• Series: PME repair kit
• SubTypes: Repair Kit

EP PP179017

• Type: Service Kit

• SubTypes: Retaining Ring

EP PRASA10016L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 16
• Stroke MM: 406
• SubTypes: POW'R-RISER Jack Pneumatic

• Capacity Imperial Tons: 100
• Capacity KN: 889

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS60, PRU13, PRU14, PRU110, PRUS126, PRE5, PRE7, PRE9, PRE11, PRE14, PRE18, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PRASA10027L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 27
• Stroke MM: 686
• SubTypes: POW'R-RISER Jack Pneumatic

• Capacity Imperial Tons: 100
• Capacity KN: 889

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS60, PRU13, PRU14, PRU110, PRUS137, PRE5, PRE7, PRE9, PRE11, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PRASA15027L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 26.5
• Stroke MM: 673
• SubTypes: POW'R-RISER Jack Pneumatic

• Capacity Imperial Tons: 150
• Capacity KN: 1333

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS150, PRU151, PRU153, PRU155, PRU1510, PRUS1537, PRE5, PRE7, PRE9, PRE11, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PTW1000C

• Type: Torque Wrench

• Product Group: Torque Wrenches, Torque Wrench Pumps
• Product Line: Bolting Tools
• Series: PTW
• SubTypes: Pneumatic Torque Wrench with FRL

• High speed continuous rotation for constant torque output
• Low friction planetary gearbox design minimizes wear and extends uptime
• Ergonomic, low vibration design reduces fatigue and the risk of vibration related injuries for the operator
• Low noise air motor provides quiet, consistent performance for indoor and outdoor applications
• Provided with standard reaction arm; wide assortment of custom arms and accessories are available
• Available with or without Filter-Regulator-Lubricator (FRL)
• Unique calibration certificate provided with each tool

• Set Includes: RATWS, FRL120C
• Accessories: ED6TWS, ED12TWS, ED18TWS, RATWS, ERATWS, SLRATWS, DSATWS, SRATWS, BLTWS

EP PTW2000C

• Type: Torque Wrench

• Product Group: Torque Wrenches, Torque Wrench Pumps
• Product Line: Bolting Tools
• Series: PTW
• SubTypes: Pneumatic Torque Wrench with FRL

• High speed continuous rotation for constant torque output
• Low friction planetary gearbox design minimizes wear and extends uptime
• Ergonomic, low vibration design reduces fatigue and the risk of vibration related injuries for the operator
• Low noise air motor provides quiet, consistent performance for indoor and outdoor applications
• Provided with standard reaction arm; wide assortment of custom arms and accessories are available
• Available with or without Filter-Regulator-Lubricator (FRL)
• Unique calibration certificate provided with each tool

• Set Includes: RATWS, FRL120C
• Accessories: ED6TWS, ED12TWS, ED18TWS, RATWS, ERATWS, SLRATWS, DSATWS, SRATWS, BLTWS

EP PUD1100B

PU Series electric over hydraulic pumps combine economy with high-performance - ideal for intermittent use when working with small to medium size cylinders and other hydraulic tools.

All models in the series are 2-speed for enhanced productivity, and each is supplied with a 10 ft (3 m) cord and control pendant for operator safety. The high-strength molded shroud with integral handle protects the motor from contamination and damage in industrial environments.

Within the PU Series is a selection of pumps that offer a choice of reservoir capacities, valve functions and voltage.

PUD1100 Series

• For advance and retract of single-acting cylinders
• For applications not requiring load holding
• Ideal for punching applications

PUD1300 Series

• Providing advance, hold, and retract of single-acting cylinders
• Ideal for applications requiring load holding
• For applications requiring solenoid valves

PUJ-Series

• Manual valves provide advance, hold, and retract operation
• 3 and 4-way valves for single or double-acting cylinders

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: PU
• SubTypes: Electric Pump - Economy

• The economic choice for small to medium sized tools.
• Lightweight, compact, and portable.
• Two-speed operation reduces cycle times for improved productivity.
• Ideal for intermittent duty cycles.
• Works well with long extension cords or generator-driven electrical power supplies.
• 115 VAC 50/60-cycle universal motor will operate under poor voltage supply.
• 24 VAC remote motor control with 10 ft (3 m) cord for operator safety.
• Starts under full load.
• High-strength shroud with integral handle protects the motor from contamination and damage.

• Spare Part(s): PUD1100BK

EP PREMB10016L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 16
• Stroke MM: 406
• SubTypes: POW'R-RISER Jack Electric

• Capacity Imperial Tons: 100
• Capacity KN: 889

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS60, PRU13, PRU14, PRU110, PRUS126, PRE5, PRE7, PRE9, PRE11, PRE14, PRE18, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PRAMA10016L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 16
• Stroke MM: 406
• SubTypes: POW'R-RISER Jack Pneumatic

• Capacity Imperial Tons: 100
• Capacity KN: 889

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS60, PRU13, PRU14, PRU110, PRUS126, PRE5, PRE7, PRE9, PRE11, PRE14, PRE18, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PUD1100BK

• Type: Service Kit

• Product Group: Pumps
• Series: PU (service kit)
• SubTypes: Repair Kit

EP PUD1300B

PU Series electric over hydraulic pumps combine economy with high-performance - ideal for intermittent use when working with small to medium size cylinders and other hydraulic tools.

All models in the series are 2-speed for enhanced productivity, and each is supplied with a 10 ft (3 m) cord and control pendant for operator safety. The high-strength molded shroud with integral handle protects the motor from contamination and damage in industrial environments.

Within the PU Series is a selection of pumps that offer a choice of reservoir capacities, valve functions and voltage.

PUD1100 Series

• For advance and retract of single-acting cylinders
• For applications not requiring load holding
• Ideal for punching applications

PUD1300 Series

• Providing advance, hold, and retract of single-acting cylinders
• Ideal for applications requiring load holding
• For applications requiring solenoid valves

PUJ-Series

• Manual valves provide advance, hold, and retract operation
• 3 and 4-way valves for single or double-acting cylinders

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: PU
• SubTypes: Electric Pump - Economy

• The economic choice for small to medium sized tools.
• Lightweight, compact, and portable.
• Two-speed operation reduces cycle times for improved productivity.
• Ideal for intermittent duty cycles.
• Works well with long extension cords or generator-driven electrical power supplies.
• 115 VAC 50/60-cycle universal motor will operate under poor voltage supply.
• 24 VAC remote motor control with 10 ft (3 m) cord for operator safety.
• Starts under full load.
• High-strength shroud with integral handle protects the motor from contamination and damage.

• Spare Part(s): PUD1100BK

EP PUJ1200BK1

• Type: Service Kit

• Product Group: Pumps
• Series: PU (service kit)
• SubTypes: Repair Kit

EP PUJ1400BK

• Type: Service Kit

• Product Group: Pumps
• Series: PU (service kit)
• SubTypes: Repair Kit

EP PUJ1400B

PU Series electric over hydraulic pumps combine economy with high-performance - ideal for intermittent use when working with small to medium size cylinders and other hydraulic tools.

All models in the series are 2-speed for enhanced productivity, and each is supplied with a 10 ft (3 m) cord and control pendant for operator safety. The high-strength molded shroud with integral handle protects the motor from contamination and damage in industrial environments.

Within the PU Series is a selection of pumps that offer a choice of reservoir capacities, valve functions and voltage.

PUD1100 Series

• For advance and retract of single-acting cylinders
• For applications not requiring load holding
• Ideal for punching applications

PUD1300 Series

• Providing advance, hold, and retract of single-acting cylinders
• Ideal for applications requiring load holding
• For applications requiring solenoid valves

PUJ-Series

• Manual valves provide advance, hold, and retract operation
• 3 and 4-way valves for single or double-acting cylinders

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: PU
• SubTypes: Electric Pump - Economy

• The economic choice for small to medium sized tools.
• Lightweight, compact, and portable.
• Two-speed operation reduces cycle times for improved productivity.
• Ideal for intermittent duty cycles.
• Works well with long extension cords or generator-driven electrical power supplies.
• 115 VAC 50/60-cycle universal motor will operate under poor voltage supply.
• 24 VAC remote motor control with 10 ft (3 m) cord for operator safety.
• Starts under full load.
• High-strength shroud with integral handle protects the motor from contamination and damage.

• Spare Part(s): PUJ1400BK

EP R102

Simplex R-Series Single Acting Hydraulic Cylinders are the durable, reliable, and versatile choice for general purpose industrial use. With a vast range of cylinder tonnages and strokes available it's easy to find a cylinder perfectly matched to your application.

Threaded collars offer versatility in fixturing to give you many more application possibilities. Included inside R Series Cylinders is a positive stop to limit piston travel at the end of the stroke, adding extra strength and safety to your cylinder, and cylinder life is extended by the wiper seal.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: R
• Stroke Inches: 2.19
• Stroke MM: 55.6
• SubTypes: General Purpose Cylinder

• Capacity Imperial Tons: 10
• Capacity KN: 89,0

• Single acting with heavy-duty internal retraction spring
• Solid and plated piston resists scoring & corrosion
• Heat treated grooved saddles are provided as standard
• Stop ring limits piston travel at the end of the stroke to prevent blow-out
• High flow couplers are plated to resist corrosion
• Polyurethane wipers clean the piston surface during retraction - protecting the inner cylinder assembly from dirt, moisture, and other contaminants.
• Meets ANSI/ASME B30.1 Safety Standards
• Load tested under 125% of the nominal capacity
• For working pressures up to 10,000 psi (700 bar)

• Accessories: BA10, 18348, ATS10, BR10, BCR10, BC10

EP R515245-2

• Type: Service Kit

• SubTypes: Plug

EP RA106

• Type: Hydraulic Cylinders

• Product Group: Cylinders and Jacks

EP R57

Simplex R-Series Single Acting Hydraulic Cylinders are the durable, reliable, and versatile choice for general purpose industrial use. With a vast range of cylinder tonnages and strokes available it's easy to find a cylinder perfectly matched to your application.

Threaded collars offer versatility in fixturing to give you many more application possibilities. Included inside R Series Cylinders is a positive stop to limit piston travel at the end of the stroke, adding extra strength and safety to your cylinder, and cylinder life is extended by the wiper seal.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: R
• Stroke Inches: 7.18
• Stroke MM: 182.4
• SubTypes: General Purpose Cylinder

• Capacity Imperial Tons: 5
• Capacity KN: 44,5

• Single acting with heavy-duty internal retraction spring
• Solid and plated piston resists scoring & corrosion
• Heat treated grooved saddles are provided as standard
• Stop ring limits piston travel at the end of the stroke to prevent blow-out
• High flow couplers are plated to resist corrosion
• Polyurethane wipers clean the piston surface during retraction - protecting the inner cylinder assembly from dirt, moisture, and other contaminants.
• Meets ANSI/ASME B30.1 Safety Standards
• Load tested under 125% of the nominal capacity
• For working pressures up to 10,000 psi (700 bar)

• Accessories: 18347, BCR5, BR5

EP RAC20K50

• Type: Service Kit

• SubTypes: Repair Kit

EP RAC50K50

• Type: Service Kit

• SubTypes: Repair Kit

EP QDH120

• Type: Hydraulic Cylinders
• Max Bar: 350
• Max PSI: 5000

• Product Group: Cylinders and Jacks
• Product Line: Work Holding Tools
• Series: QDH
• Stroke Inches: 0.32
• Stroke MM: 8.1
• SubTypes: Workholding Hollow Plunger Cylinder

• Load can be attached to either end of the cylinder, providing a choice of push or pull actions - both realizing full cylinder capacity
• Very high cylinder capacities contained within small dimensions allow compact fixture designs
• Spring return operation allows for easy unloading of the workpiece
• Threaded collars and base mounting holes allow mounting flexibility, including table-top surfaces and T-slots
• Nickel-plated plungers, plunger wipers and internal venting prevent corrosion and support longer operation life on allHCS models

EP RACD3010

• Technical coating reduces wear & corrosion.
• Steel piston for protection against load damage.
• Chrome plated sleeve for extra protection.
• Stop rings for piston blow-out protection.
• Rod wiper protects inner cylinder from dirt.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: RACD
• Stroke Inches: 10
• Stroke MM: 254
• SubTypes: Aluminum Center Hole Cylinder

• Capacity Imperial Tons: 30
• Capacity KN: 266,9

EP RACD10010

• Technical coating reduces wear & corrosion.
• Steel piston for protection against load damage.
• Chrome plated sleeve for extra protection.
• Stop rings for piston blow-out protection.
• Rod wiper protects inner cylinder from dirt.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: RACD
• Stroke Inches: 10
• Stroke MM: 254
• SubTypes: Aluminum Center Hole Cylinder

• Capacity Imperial Tons: 100
• Capacity KN: 889,6

EP R59

Simplex R-Series Single Acting Hydraulic Cylinders are the durable, reliable, and versatile choice for general purpose industrial use. With a vast range of cylinder tonnages and strokes available it's easy to find a cylinder perfectly matched to your application.

Threaded collars offer versatility in fixturing to give you many more application possibilities. Included inside R Series Cylinders is a positive stop to limit piston travel at the end of the stroke, adding extra strength and safety to your cylinder, and cylinder life is extended by the wiper seal.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: R
• Stroke Inches: 9.18
• Stroke MM: 233.2
• SubTypes: General Purpose Cylinder

• Capacity Imperial Tons: 5
• Capacity KN: 44,5

• Single acting with heavy-duty internal retraction spring
• Solid and plated piston resists scoring & corrosion
• Heat treated grooved saddles are provided as standard
• Stop ring limits piston travel at the end of the stroke to prevent blow-out
• High flow couplers are plated to resist corrosion
• Polyurethane wipers clean the piston surface during retraction - protecting the inner cylinder assembly from dirt, moisture, and other contaminants.
• Meets ANSI/ASME B30.1 Safety Standards
• Load tested under 125% of the nominal capacity
• For working pressures up to 10,000 psi (700 bar)

• Accessories: 18347, BCR5, BR5

EP RACH1006005

• Type: Service Kit

• SubTypes: Tube

EP RACH1006

RACH-Series Hollow Plunger Hydraulic Cylinders (sometimes called center-hole cylinders) feature a hollow plunger with an internal thread to allow fixing to the component to be pulled. This makes them the ideal choice for when you need a lighter, more portable cylinder for applications such as tensioning, testing, pulling, and lifting. Each RACH Cylinder is rated for up to 10,000 psi (700 bar) and compliant with ASME B30.1.

Each RACH Cylinder is single-acting and uses a high-strength return spring for rapid retraction. All are equipped with bolt-on hardened steel saddles and a steel base plate for increased durability.

Aluminum is not only lightweight, but also inherently less corrosive than steel, which makes it a great material for use in many caustic environments. For enhanced protection, RACH Aluminum Cylinders are finished with an anodized hard coat finish to resist damage and extend cylinder life.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RACH
• Stroke Inches: 5.91
• Stroke MM: 150
• SubTypes: Aluminum Hollow Plunger Cylinder

• Hollow plunger design allows for both pull and push forces
• Composite bearings increase cylinder life and side load resistance
• Hard coat finish on all surfaces resists damage and extends cylinder life
• Handles included on all models
• Floating center tube increases seal life
• Steel baseplate and saddle for protection against load-induced damage
• Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
• High-strength return spring for rapid cylinder retraction
• CR400 coupler and dustcap included on all models
• All cylinders meet ASME B-30.1 standards

EP RACH1006040

• Type: Service Kit

• SubTypes: Plunger Kit

EP RACD5010

• Technical coating reduces wear & corrosion.
• Steel piston for protection against load damage.
• Chrome plated sleeve for extra protection.
• Stop rings for piston blow-out protection.
• Rod wiper protects inner cylinder from dirt.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: RACD
• Stroke Inches: 10
• Stroke MM: 254
• SubTypes: Aluminum Center Hole Cylinder

• Capacity Imperial Tons: 50
• Capacity KN: 444,8

EP RACH100K50

• Type: Service Kit

• SubTypes: Repair Kit

EP RACH2010

RACH-Series Hollow Plunger Hydraulic Cylinders (sometimes called center-hole cylinders) feature a hollow plunger with an internal thread to allow fixing to the component to be pulled. This makes them the ideal choice for when you need a lighter, more portable cylinder for applications such as tensioning, testing, pulling, and lifting. Each RACH Cylinder is rated for up to 10,000 psi (700 bar) and compliant with ASME B30.1.

Each RACH Cylinder is single-acting and uses a high-strength return spring for rapid retraction. All are equipped with bolt-on hardened steel saddles and a steel base plate for increased durability.

Aluminum is not only lightweight, but also inherently less corrosive than steel, which makes it a great material for use in many caustic environments. For enhanced protection, RACH Aluminum Cylinders are finished with an anodized hard coat finish to resist damage and extend cylinder life.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RACH
• Stroke Inches: 9.84
• Stroke MM: 250
• SubTypes: Aluminum Hollow Plunger Cylinder

• Hollow plunger design allows for both pull and push forces
• Composite bearings increase cylinder life and side load resistance
• Hard coat finish on all surfaces resists damage and extends cylinder life
• Handles included on all models
• Floating center tube increases seal life
• Steel baseplate and saddle for protection against load-induced damage
• Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
• High-strength return spring for rapid cylinder retraction
• CR400 coupler and dustcap included on all models
• All cylinders meet ASME B-30.1 standards

EP RACH20K50

• Type: Service Kit

• SubTypes: Repair Kit

EP RACH602005

• Type: Service Kit

• SubTypes: Tube

EP RACL504

RACL-Series Aluminum Cylinders include a lock nut that gives the reassurance of safe mechanical load holding for extended periods. Each cylinder is single-acting with a high-strength return spring for rapid retraction. The integral stop ring prevents plunger over-travel. All are equipped with bolt-on hardened steel saddles and a steel base plate for increased durability.

Enerpac RACL Lock Nut Aluminum Hydraulic Cylinders can change the way you think about your cylinder applications. With approximately half of the weight of equivalent steel models, they combine an impressive power to weight ratio with the convenience of easier transport and positioning. RACL cylinders are rated for 10,000 psi (700 bar) and comply with ASME B30.1.

Aluminum is not only lightweight, but also inherently less corrosive than steel, which makes it a great material for use in many caustic environments. For enhanced protection, Enerpac RACL Aluminum Cylinders are finished with an anodized hard coat finish to resist damage and extend cylinder life.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RACL
• Stroke Inches: 3.94
• Stroke MM: 100
• SubTypes: Aluminum Lock Nut Cylinder

• Aluminum Lock Nut provides mechanical load holding for extended periods
• Hardened steel stop ring increases cylinder life and resistance to side-loads of up to 5%
• Hard coat finish on all surfaces resists damage and extends cylinder life
• Composite bearings increase cylinder life and side load resistance
• Handles included on all models
• Steel base plate and saddle for protection against load-induced damage
• Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
• High-strength return spring for rapid cylinder retraction
• CR400 coupler and dustcap included on all models
• All cylinders meet ASME B-30.1 standards

• Accessories: CATS50

EP RACL204

RACL-Series Aluminum Cylinders include a lock nut that gives the reassurance of safe mechanical load holding for extended periods. Each cylinder is single-acting with a high-strength return spring for rapid retraction. The integral stop ring prevents plunger over-travel. All are equipped with bolt-on hardened steel saddles and a steel base plate for increased durability.

Enerpac RACL Lock Nut Aluminum Hydraulic Cylinders can change the way you think about your cylinder applications. With approximately half of the weight of equivalent steel models, they combine an impressive power to weight ratio with the convenience of easier transport and positioning. RACL cylinders are rated for 10,000 psi (700 bar) and comply with ASME B30.1.

Aluminum is not only lightweight, but also inherently less corrosive than steel, which makes it a great material for use in many caustic environments. For enhanced protection, Enerpac RACL Aluminum Cylinders are finished with an anodized hard coat finish to resist damage and extend cylinder life.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RACL
• Stroke Inches: 3.94
• Stroke MM: 100
• SubTypes: Aluminum Lock Nut Cylinder

• Aluminum Lock Nut provides mechanical load holding for extended periods
• Hardened steel stop ring increases cylinder life and resistance to side-loads of up to 5%
• Hard coat finish on all surfaces resists damage and extends cylinder life
• Composite bearings increase cylinder life and side load resistance
• Handles included on all models
• Steel base plate and saddle for protection against load-induced damage
• Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
• High-strength return spring for rapid cylinder retraction
• CR400 coupler and dustcap included on all models
• All cylinders meet ASME B-30.1 standards

EP RAR1004

RAR-Series Double Acting Hydraulic Cylinders provide a rapid and more controlled plunger retraction than spring return or load return types. The hydraulic return method continues to work effectively regardless of hose lengths and system losses, maintaining efficiency and productivity. Each RAR Cylinder is rated for up to 10,000 psi (700 bar) and compliant with ASME B30.1.

The aluminum construction of RAR Cylinders means they are not only lightweight, but also less corrosive than steel equivalents. This helps to maintain durability in many caustic environments. For enhanced protection, RAR Aluminum Cylinders are finished with an anodized hard coat finish to resist damage and extend cylinder life. Handles featured on all models enhance their portability.

Each RAR Cylinder is equipped with a bolt-on hardened steel saddle and a steel base plate for increased durability. Optional Tilt Saddles can help to support the load evenly and alleviate unwanted side-load.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RAR
• Stroke Inches: 3.94
• Stroke MM: 100
• SubTypes: Aluminum Cylinder

• Double-acting for rapid retraction, regardless of hose lengths and system losses
• Composite bearings increase cylinder life and side load resistance
• Hard coat finish on all surfaces resists damage and extends cylinder life
• Handles included on all models
• Steel base plate and saddle for protection against load- induced damage
• Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
• Built-in safety valve prevents accidental over-pressurization

• Accessories: CATS101

EP RAL502

Simplex RAL Series Aluminum Hydraulic Cylinders feature lock nut that provide the reassurance of safe mechanical load holding for extended periods. These are approximately half the weight of steel equivalents and are expertly engineered to withstand tough applications in harsh conditions.

Aluminum is not only lighter, but also inherently less corrosive than steel, which makes it a great material for use in many caustic environments. A carrying handle provided on all RAL cylinders also enhance portability.

Inside the cylinder is a high-strength return spring for plunger retraction and stop rings for protection against blow out. The cylinder exterior is finished with an anodized hard coat to extend cylinder life, and a wiper protects the inner cylinder assembly from dirt, moisture, and other contaminants.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: RAL
• Stroke Inches: 2
• Stroke MM: 50.8
• SubTypes: Aluminum Locknut Cylinder

• Capacity Imperial Tons: 50
• Capacity KN: 444,8

• Approximately half the weight of steel cylinders
• Lock nut for mechanical load holding for extended periods
• Heavy duty spring delivers fast and full retraction
• Hard anodized coating reduces wear and corrosion
• Stop rings prevent piston blow-out
• Wiper protects inner cylinder from dirt.
• Meets ANSI/ASME B30.1 Safety Standards
• Load tested under 125% of the nominal capacity
• For working pressures up to 10,000 psi (700 bar)

EP RAR1006040

• Type: Service Kit

• SubTypes: Plunger Kit

EP RAR100K50

• Type: Service Kit

• SubTypes: Repair Kit

EP RARH3010

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10150

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RARH
• Stroke Inches: 9.84
• Stroke MM: 250
• SubTypes: Aluminum Hollow Plunger Cylinder

• Lighter and shorter collapsed height than equivalent RACH single-acting models
• Double-acting for rapid retraction, regardless of hose lengths or system losses
• Built-in safety valve prevents accidental overpressurization
• Hollow plunger design allows for both pull and push forces
• Composite bearings increase cylinder life and side load resistance
• Hard coat finish on all surfaces resists damage and extends cylinder life
• Handles included on all models
• Floating center tube increases seal life
• Steel baseplate and saddle for protection against load-induced damage
• Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
• CR400 coupler and dust cap included on all models
• All cylinders meet ASME B-30.1 standards

• Accessories: HP3015

EP RARH606

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10150

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RARH
• Stroke Inches: 5.91
• Stroke MM: 150
• SubTypes: Aluminum Hollow Plunger Cylinder

• Lighter and shorter collapsed height than equivalent RACH single-acting models
• Double-acting for rapid retraction, regardless of hose lengths or system losses
• Built-in safety valve prevents accidental overpressurization
• Hollow plunger design allows for both pull and push forces
• Composite bearings increase cylinder life and side load resistance
• Hard coat finish on all surfaces resists damage and extends cylinder life
• Handles included on all models
• Floating center tube increases seal life
• Steel baseplate and saddle for protection against load-induced damage
• Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
• CR400 coupler and dust cap included on all models
• All cylinders meet ASME B-30.1 standards

• Accessories: HP5016

EP RC10010

RC-TRIO is the next generation of the legendary Enerpac RC-Series single acting hydraulic cylinders. These hydraulic jacks include many advanced features to ensure superior durability, versatility, and productivity.

A pre-tensioned spring provides fast plunger retraction and enhanced productivity. The robust bearing system features composite wear bands and a hardened stop ring to resist side-load which minimizes damage and repairs. The plunger wiper, high-grade polyethylene seals and tough external finishes also help towards an extended service life.

With so many hydraulic cylinder models to choose from, we’re confident you’ll find the perfect match for your applications, and if you already own prior RC-Series cylinders, the good news is the new cylinders share the same familiar dimensions and threads for full compatibility.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RC
• Stroke Inches: 10.25
• Stroke MM: 260
• SubTypes: General Purpose Cylinder

• Bearing system with composite wear bands for optimal sideload resistance
• Strengthened stop ring improves durability and side load resistance
• Trio Hybrid pre-tensioned spring system provides faster retraction
• High-grade polyethylene seals for low wear and long service life
• Plunger wiper reduces contamination, extending cylinder life.
• Collar and plunger threads and base mounting holes enable easy fixturing (on most models)
• Standard certified lifting eyes on cylinder models above 55 lbs. (25 kg) weight.
• Interchangeable with optional CHM6 carrying handle
• Designed for use in all positions
• Baked enamel finish for increased corrosion resistance
• Includes CR400 coupler, dust cap and collar thread protector
• RC-Series model numbers, external dimensions and threads remain unchanged from prior RC Series cylinders

• Spare Part(s): RC100044, HCL50045, RC10010040, RC100NK0, RC100NKS3, RC100NKS, RC100NKB1, RC100NKB2, RC100NKB3, RC100NKB4, RC100NKW
• Accessories: CATS100, CHM6

EP RC10044

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Stop Ring

EP RC1006K

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RC1010

RC-TRIO is the next generation of the legendary Enerpac RC-Series single acting hydraulic cylinders. These hydraulic jacks include many advanced features to ensure superior durability, versatility, and productivity.

A pre-tensioned spring provides fast plunger retraction and enhanced productivity. The robust bearing system features composite wear bands and a hardened stop ring to resist side-load which minimizes damage and repairs. The plunger wiper, high-grade polyethylene seals and tough external finishes also help towards an extended service life.

With so many hydraulic cylinder models to choose from, we’re confident you’ll find the perfect match for your applications, and if you already own prior RC-Series cylinders, the good news is the new cylinders share the same familiar dimensions and threads for full compatibility.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RC
• Stroke Inches: 10.13
• Stroke MM: 257
• SubTypes: General Purpose Cylinder

• Bearing system with composite wear bands for optimal sideload resistance
• Strengthened stop ring improves durability and side load resistance
• Trio Hybrid pre-tensioned spring system provides faster retraction
• High-grade polyethylene seals for low wear and long service life
• Plunger wiper reduces contamination, extending cylinder life.
• Collar and plunger threads and base mounting holes enable easy fixturing (on most models)
• Standard certified lifting eyes on cylinder models above 55 lbs. (25 kg) weight.
• Interchangeable with optional CHM6 carrying handle
• Designed for use in all positions
• Baked enamel finish for increased corrosion resistance
• Includes CR400 coupler, dust cap and collar thread protector
• RC-Series model numbers, external dimensions and threads remain unchanged from prior RC Series cylinders

• Spare Part(s): RC106044, RC1010040, RC10NK0, RC10K35, RC10NKS, RC10NKB2, RC10NKB3, RC10NKW
• Accessories: A92, A102G, CATS12, JBI10, RB10, AW102, REB10, REP10

EP RC102K

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Seal Kit

EP RC10K52

• Type: Service Kit

• SubTypes: Repair Kit

EP RC10K71

• Type: Service Kit

• SubTypes: Repair Kit

EP RC10K72

• Type: Service Kit

• SubTypes: Repair Kit

EP RC10NK0

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RC15044

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Stop Ring

EP RC15K1

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP G2512L

This G-Series Liquid Filled Pressure Gauge contains glycerin to protect pressure sensing parts from vibration, sudden pressure changes, and moisture.

The dual scale face shows both psi and bar readings, and the extensive range includes a wide selection of models with maximum working pressures ranging from 100 to 15000 psi (7 to 1000 bar).

When using your gauges for high-cycle applications, we recommend using gauge snubbers or needle valves.

• Type: Gauge
• Max Bar: 20
• Max PSI: 300

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: G
• SubTypes: Pressure Gauge

• Calibrated in dual scale reading in psi and bar
• All pressure sensing parts sealed and dampened by glycerine for long life
• Includes safety blow-out disk and pressure equalizing membrane
• Gauge snubbers or needle valves recommended for high cycle applications

EP G2513L

This G-Series Liquid Filled Pressure Gauge contains glycerin to protect pressure sensing parts from vibration, sudden pressure changes, and moisture.

The dual scale face shows both psi and bar readings, and the extensive range includes a wide selection of models with maximum working pressures ranging from 100 to 15000 psi (7 to 1000 bar).

When using your gauges for high-cycle applications, we recommend using gauge snubbers or needle valves.

• Type: Gauge
• Max Bar: 40
• Max PSI: 600

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: G
• SubTypes: Pressure Gauge

• Calibrated in dual scale reading in psi and bar
• All pressure sensing parts sealed and dampened by glycerine for long life
• Includes safety blow-out disk and pressure equalizing membrane
• Gauge snubbers or needle valves recommended for high cycle applications

EP G2514L

This G-Series Liquid Filled Pressure Gauge contains glycerin to protect pressure sensing parts from vibration, sudden pressure changes, and moisture.

The dual scale face shows both psi and bar readings, and the extensive range includes a wide selection of models with maximum working pressures ranging from 100 to 15000 psi (7 to 1000 bar).

When using your gauges for high-cycle applications, we recommend using gauge snubbers or needle valves.

• Type: Gauge
• Max Bar: 70
• Max PSI: 1000

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: G
• SubTypes: Pressure Gauge

• Calibrated in dual scale reading in psi and bar
• All pressure sensing parts sealed and dampened by glycerine for long life
• Includes safety blow-out disk and pressure equalizing membrane
• Gauge snubbers or needle valves recommended for high cycle applications

EP G2515L

This G-Series Liquid Filled Pressure Gauge contains glycerin to protect pressure sensing parts from vibration, sudden pressure changes, and moisture.

The dual scale face shows both psi and bar readings, and the extensive range includes a wide selection of models with maximum working pressures ranging from 100 to 15000 psi (7 to 1000 bar).

When using your gauges for high-cycle applications, we recommend using gauge snubbers or needle valves.

• Type: Gauge
• Max Bar: 140
• Max PSI: 2000

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: G
• SubTypes: Pressure Gauge

• Calibrated in dual scale reading in psi and bar
• All pressure sensing parts sealed and dampened by glycerine for long life
• Includes safety blow-out disk and pressure equalizing membrane
• Gauge snubbers or needle valves recommended for high cycle applications

EP G2516L

This G-Series Liquid Filled Pressure Gauge contains glycerin to protect pressure sensing parts from vibration, sudden pressure changes, and moisture.

The dual scale face shows both psi and bar readings, and the extensive range includes a wide selection of models with maximum working pressures ranging from 100 to 15000 psi (7 to 1000 bar).

When using your gauges for high-cycle applications, we recommend using gauge snubbers or needle valves.

• Type: Gauge
• Max Bar: 200
• Max PSI: 3000

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: G
• SubTypes: Pressure Gauge

• Calibrated in dual scale reading in psi and bar
• All pressure sensing parts sealed and dampened by glycerine for long life
• Includes safety blow-out disk and pressure equalizing membrane
• Gauge snubbers or needle valves recommended for high cycle applications

EP G2516SL

This G-Series Liquid Filled Pressure Gauge contains glycerin to protect pressure sensing parts from vibration, sudden pressure changes, and moisture.

The dual scale face shows both psi and bar readings, and the extensive range includes a wide selection of models with maximum working pressures ranging from 100 to 15000 psi (7 to 1000 bar).

When using your gauges for high-cycle applications, we recommend using gauge snubbers or needle valves.

• Type: Gauge
• Max Bar: 200
• Max PSI: 3000

• Product Group: Gauges, Pumps
• Product Line: Work Holding Tools
• Series: G
• SubTypes: Pressure Gauge

• plus/minus 1.5% accuracy of full scale
• All pressure sensing parts sealed and dampened by glycerine for long life
• Includes safety blow-out disk and pressure equalizing membrane to prevent overpressurization
• Copper alloy, coiled safety Bourdon tube for 1000 psi and higher
• Dual psi and bar scale readings, 1.5 inch gauge face

EP GF120B

GF-Series gauges are calibrated with dual scales for reading for pressure and force.

The force readings allow you to measure external loads, such as those supported by a cylinder or jack, or the force used for pressing parts.

The glycerin within the gauge protects pressure sensing parts from vibration, sudden changes in pressure and from moisture.

The GF-Series Gauges feature a 4” (100 mm) diameter face for easy readability, and a stainless-steel casing for corrosion resistance.

• Type: Gauge
• Max Bar: 700
• Max PSI: 10000

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools
• Series: GF
• SubTypes: Force and Pressure Gauge

• Excellent readability; 4 inch diameter gauge face.
• Fast, easy installation
• Stainless steel gauge cases for corrosion resistance
• Calibrated with dual scale reading for psi and bar

EP GA90

• An intermittent portable foot controlled pump best suited for pressing, production and shop tool applications. Runs effectively on 10 CFM (10 pi3) / @ 60 - 150 PSI (4,13 - 10,34 bar).
• 3 position non-slip, diamond grip treadle for safe advance, hold & retract operation.
• Quiet operation - 85 dba @ 10,000 psi (700 bar) for in-house production.
• Rugged all metal construction.
• High quality rubber gasket seals.
• Integrated non-spill vent / oil level indicator.
• Pedal can be used to reduce operator strain by locking in the release position.
• Four mountable non-skid rubber feet can be used to make your pump stationary.
• A non-slip diamond plate texture gives the user safe and controlled foot pivoting action.

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: GA - Simplex
• SubTypes: Air Pump - Foot Pump

EP G831446

• Type: Service Kit

• SubTypes: Repair Part

EP G2517SL

This G-Series Liquid Filled Pressure Gauge contains glycerin to protect pressure sensing parts from vibration, sudden pressure changes, and moisture.

The dual scale face shows both psi and bar readings, and the extensive range includes a wide selection of models with maximum working pressures ranging from 100 to 15000 psi (7 to 1000 bar).

When using your gauges for high-cycle applications, we recommend using gauge snubbers or needle valves.

• Type: Gauge
• Max Bar: 400
• Max PSI: 6000

• Product Group: Gauges, Pumps
• Product Line: Work Holding Tools
• Series: G
• SubTypes: Pressure Gauge

• plus/minus 1.5% accuracy of full scale
• All pressure sensing parts sealed and dampened by glycerine for long life
• Includes safety blow-out disk and pressure equalizing membrane to prevent overpressurization
• Copper alloy, coiled safety Bourdon tube for 1000 psi and higher
• Dual psi and bar scale readings, 1.5 inch gauge face

EP G2517L

This G-Series Liquid Filled Pressure Gauge contains glycerin to protect pressure sensing parts from vibration, sudden pressure changes, and moisture.

The dual scale face shows both psi and bar readings, and the extensive range includes a wide selection of models with maximum working pressures ranging from 100 to 15000 psi (7 to 1000 bar).

When using your gauges for high-cycle applications, we recommend using gauge snubbers or needle valves.

• Type: Gauge
• Max Bar: 400
• Max PSI: 6000

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: G
• SubTypes: Pressure Gauge

• Calibrated in dual scale reading in psi and bar
• All pressure sensing parts sealed and dampened by glycerine for long life
• Includes safety blow-out disk and pressure equalizing membrane
• Gauge snubbers or needle valves recommended for high cycle applications

EP GA3

• Type: Gauge Accessory
• Max Bar: 700
• Max PSI: 10000

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: GA
• SubTypes: Gauge Adaptor

• For easy mounting of a pressure gauge into your system
• Male end screws into pump or cylinder port, female end accepts hose or coupler, third port is for gauge connection
• Simplifies gauge installation and reading

EP G4089L

This G-Series Liquid Filled Pressure Gauge contains glycerin to protect pressure sensing parts from vibration, sudden pressure changes, and moisture.

The dual scale face shows both psi and bar readings, and the extensive range includes a wide selection of models with maximum working pressures ranging from 100 to 15000 psi (7 to 1000 bar).

When using your gauges for high-cycle applications, we recommend using gauge snubbers or needle valves.

• Type: Gauge
• Max Bar: 1000
• Max PSI: 15000

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools
• Series: G
• SubTypes: Pressure Gauge

• Calibrated in dual scale reading in psi and bar
• All pressure sensing parts sealed and dampened by glycerine for long life
• Includes safety blow-out disk and pressure equalizing membrane
• Gauge snubbers or needle valves recommended for high cycle applications

EP G416044

• Type: Service Kit

• SubTypes: Wiper Ring

EP G953107

• Type: Service Kit

• SubTypes: Rod Bearing

EP G836028

• Type: Service Kit

• SubTypes: Screw

EP G586900SR-10750

• Type: Service Kit

• SubTypes: Safety Valve

EP G385044

• Type: Service Kit

• SubTypes: Stop Ring

EP G4039L

This G-Series Liquid Filled Pressure Gauge contains glycerin to protect pressure sensing parts from vibration, sudden pressure changes, and moisture.

The dual scale face shows both psi and bar readings, and the extensive range includes a wide selection of models with maximum working pressures ranging from 100 to 15000 psi (7 to 1000 bar).

When using your gauges for high-cycle applications, we recommend using gauge snubbers or needle valves.

• Type: Gauge
• Max Bar: 700
• Max PSI: 10000

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools
• Series: G
• SubTypes: Pressure Gauge

• Calibrated in dual scale reading in psi and bar
• All pressure sensing parts sealed and dampened by glycerine for long life
• Includes safety blow-out disk and pressure equalizing membrane
• Gauge snubbers or needle valves recommended for high cycle applications

EP G4088L

This G-Series Liquid Filled Pressure Gauge contains glycerin to protect pressure sensing parts from vibration, sudden pressure changes, and moisture.

The dual scale face shows both psi and bar readings, and the extensive range includes a wide selection of models with maximum working pressures ranging from 100 to 15000 psi (7 to 1000 bar).

When using your gauges for high-cycle applications, we recommend using gauge snubbers or needle valves.

• Type: Gauge
• Max Bar: 700
• Max PSI: 10000

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools
• Series: G
• SubTypes: Pressure Gauge

• Calibrated in dual scale reading in psi and bar
• All pressure sensing parts sealed and dampened by glycerine for long life
• Includes safety blow-out disk and pressure equalizing membrane
• Gauge snubbers or needle valves recommended for high cycle applications

EP G830040

• Type: Service Kit

• SubTypes: Plunger

EP G382107

• Type: Service Kit

• SubTypes: Bearing Kit

EP G2536L

This G-Series Liquid Filled Pressure Gauge contains glycerin to protect pressure sensing parts from vibration, sudden pressure changes, and moisture.

The dual scale face shows both psi and bar readings, and the extensive range includes a wide selection of models with maximum working pressures ranging from 100 to 15000 psi (7 to 1000 bar).

When using your gauges for high-cycle applications, we recommend using gauge snubbers or needle valves.

• Type: Gauge
• Max Bar: 1000
• Max PSI: 15000

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: G
• SubTypes: Pressure Gauge

• Calibrated in dual scale reading in psi and bar
• All pressure sensing parts sealed and dampened by glycerine for long life
• Includes safety blow-out disk and pressure equalizing membrane
• Gauge snubbers or needle valves recommended for high cycle applications

EP G2537R

This G-Series Liquid Filled Pressure Gauge contains glycerin to protect pressure sensing parts from vibration, sudden pressure changes, and moisture.

The dual scale face shows both psi and bar readings, and the extensive range includes a wide selection of models with maximum working pressures ranging from 100 to 15000 psi (7 to 1000 bar).

When using your gauges for high-cycle applications, we recommend using gauge snubbers or needle valves.

• Type: Gauge
• Max Bar: 700
• Max PSI: 10000

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: G
• SubTypes: Pressure Gauge

• Calibrated in dual scale reading in psi and bar
• All pressure sensing parts sealed and dampened by glycerine for long life
• Includes safety blow-out disk and pressure equalizing membrane
• Gauge snubbers or needle valves recommended for high cycle applications

EP G898107

• Type: Service Kit

• SubTypes: Bearing Kit

EP G2534R

This G-Series Liquid Filled Pressure Gauge contains glycerin to protect pressure sensing parts from vibration, sudden pressure changes, and moisture.

The dual scale face shows both psi and bar readings, and the extensive range includes a wide selection of models with maximum working pressures ranging from 100 to 15000 psi (7 to 1000 bar).

When using your gauges for high-cycle applications, we recommend using gauge snubbers or needle valves.

• Type: Gauge
• Max Bar: 400
• Max PSI: 6000

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: G
• SubTypes: Pressure Gauge

• Calibrated in dual scale reading in psi and bar
• All pressure sensing parts sealed and dampened by glycerine for long life
• Includes safety blow-out disk and pressure equalizing membrane
• Gauge snubbers or needle valves recommended for high cycle applications

EP G899044

• Type: Service Kit

• SubTypes: Ring

EP GA4

• Type: Gauge Accessory
• Max Bar: 700
• Max PSI: 10000

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: GA
• SubTypes: Gauge Adaptor

• For easy mounting of a pressure gauge into your system
• Male end screws into pump or cylinder port, female end accepts hose or coupler, third port is for gauge connection
• Simplifies gauge installation and reading

EP GF510P

GF-Series gauges are calibrated with dual scales for reading for pressure and force.

The force readings allow you to measure external loads, such as those supported by a cylinder or jack, or the force used for pressing parts.

The glycerin within the gauge protects pressure sensing parts from vibration, sudden changes in pressure and from moisture.

The GF-Series Gauges feature a 4” (100 mm) diameter face for easy readability, and a stainless-steel casing for corrosion resistance.

• Type: Gauge
• Max Bar: 700
• Max PSI: 10000

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools
• Series: GF
• SubTypes: Force and Pressure Gauge

• Excellent readability; 4 inch diameter gauge face.
• Fast, easy installation
• Stainless steel gauge cases for corrosion resistance
• Calibrated with dual scale reading for psi and bar

EP GF813B

GF-Series gauges are calibrated with dual scales for reading for pressure and force.

The force readings allow you to measure external loads, such as those supported by a cylinder or jack, or the force used for pressing parts.

The glycerin within the gauge protects pressure sensing parts from vibration, sudden changes in pressure and from moisture.

The GF-Series Gauges feature a 4” (100 mm) diameter face for easy readability, and a stainless-steel casing for corrosion resistance.

• Type: Gauge
• Max Bar: 700
• Max PSI: 10000

• Product Group: Gauges, Pumps
• Product Line: Industrial Tools
• Series: GF
• SubTypes: Force and Pressure Gauge

• Excellent readability; 4 inch diameter gauge face.
• Fast, easy installation
• Stainless steel gauge cases for corrosion resistance
• Calibrated with dual scale reading for psi and bar

EP H7230

H700-Series Hoses have a safety factor of 4:1 to provide the reassurance and reliability needed for demanding high-pressure applications.

Each hose contains two layers of steel wire braids covered by a polyurethane sleeve - providing the strength and abrasion resistance needed for repeated use in tough working environments.

Diameters available 0.25 and 0.38 (6.4 and 9.7mm), and connection types include 1/4 NPTF 3/8 NPTF and CH604.

A variety of lengths are available up to 50 ft (15 m), and the vinyl strain relief guard on both ends of hose helps to improve hose life and durability.

• Type: Hose
• Max Bar: 700
• Max PSI: 10000

• Product Group: Hoses, Pumps
• Product Line: Industrial Tools
• Series: H700
• SubTypes: Thermo-plastic Hose

• For demanding applications, featuring a 4:1 safety factor
• Maximum working pressure of 10,000 psi
• Outside jacket is polyurethane, to provide maximum abrasion resistance
• Exhibits low volumetric expansion under pressure to enhance overall system efficiency
• Vinyl strain relief guard on both ends of hose to improve life and durability on all models.

EP H7350

H700-Series Hoses have a safety factor of 4:1 to provide the reassurance and reliability needed for demanding high-pressure applications.

Each hose contains two layers of steel wire braids covered by a polyurethane sleeve - providing the strength and abrasion resistance needed for repeated use in tough working environments.

Diameters available 0.25 and 0.38 (6.4 and 9.7mm), and connection types include 1/4 NPTF 3/8 NPTF and CH604.

A variety of lengths are available up to 50 ft (15 m), and the vinyl strain relief guard on both ends of hose helps to improve hose life and durability.

• Type: Hose
• Max Bar: 700
• Max PSI: 10000

• Product Group: Hoses, Pumps
• Product Line: Industrial Tools
• Series: H700
• SubTypes: Thermo-plastic Hose

• For demanding applications, featuring a 4:1 safety factor
• Maximum working pressure of 10,000 psi
• Outside jacket is polyurethane, to provide maximum abrasion resistance
• Exhibits low volumetric expansion under pressure to enhance overall system efficiency
• Vinyl strain relief guard on both ends of hose to improve life and durability on all models.

EP H7250

H700-Series Hoses have a safety factor of 4:1 to provide the reassurance and reliability needed for demanding high-pressure applications.

Each hose contains two layers of steel wire braids covered by a polyurethane sleeve - providing the strength and abrasion resistance needed for repeated use in tough working environments.

Diameters available 0.25 and 0.38 (6.4 and 9.7mm), and connection types include 1/4 NPTF 3/8 NPTF and CH604.

A variety of lengths are available up to 50 ft (15 m), and the vinyl strain relief guard on both ends of hose helps to improve hose life and durability.

• Type: Hose
• Max Bar: 700
• Max PSI: 10000

• Product Group: Hoses, Pumps
• Product Line: Industrial Tools
• Series: H700
• SubTypes: Thermo-plastic Hose

• For demanding applications, featuring a 4:1 safety factor
• Maximum working pressure of 10,000 psi
• Outside jacket is polyurethane, to provide maximum abrasion resistance
• Exhibits low volumetric expansion under pressure to enhance overall system efficiency
• Vinyl strain relief guard on both ends of hose to improve life and durability on all models.

EP H9203

H900-Series Hydraulic Hoses are designed to comply with the Material Handling Institute IJ100 hose specification. They provide the durability needed for repeated heavy-duty high-pressure applications and offer the optimum combination of flexibility and low &lsquo

EP H9206

H900-Series Hydraulic Hoses are designed to comply with the Material Handling Institute IJ100 hose specification. They provide the durability needed for repeated heavy-duty high-pressure applications and offer the optimum combination of flexibility and low &lsquo

EP H9206Q

H900-Series Hydraulic Hoses are designed to comply with the Material Handling Institute IJ100 hose specification. They provide the durability needed for repeated heavy-duty high-pressure applications and offer the optimum combination of flexibility and low &lsquo

EP H9206S

H900-Series Hydraulic Hoses are designed to comply with the Material Handling Institute IJ100 hose specification. They provide the durability needed for repeated heavy-duty high-pressure applications and offer the optimum combination of flexibility and low &lsquo

EP H9250

H900-Series Hydraulic Hoses are designed to comply with the Material Handling Institute IJ100 hose specification. They provide the durability needed for repeated heavy-duty high-pressure applications and offer the optimum combination of flexibility and low &lsquo

EP H9350

H900-Series Hydraulic Hoses are designed to comply with the Material Handling Institute IJ100 hose specification. They provide the durability needed for repeated heavy-duty high-pressure applications and offer the optimum combination of flexibility and low &lsquo

EP HA20

• Type: Hose
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: HA
• SubTypes: Industrial Grade Hose

EP HA7210

H700-Series Hoses have a safety factor of 4:1 to provide the reassurance and reliability needed for demanding high-pressure applications.

Each hose contains two layers of steel wire braids covered by a polyurethane sleeve - providing the strength and abrasion resistance needed for repeated use in tough working environments.

A variety of lengths are available up to 50 ft (15 m), and the vinyl strain relief guard on both ends of hose helps to improve hose life and durability.

• Type: Hose
• Max Bar: 700
• Max PSI: 10000

• Product Group: Hoses, Pumps
• Product Line: Industrial Tools
• Series: H700
• SubTypes: Thermo-plastic Hose

• For demanding applications, featuring a 4:1 safety factor
• Maximum working pressure of 10,000 psi
• Outside jacket is polyurethane, to provide maximum abrasion resistance
• Exhibits low volumetric expansion under pressure to enhance overall system efficiency
• Vinyl strain relief guard on both ends of hose to improve life and durability on all models.

EP HB7206

H700-Series Hoses have a safety factor of 4:1 to provide the reassurance and reliability needed for demanding high-pressure applications.

Each hose contains two layers of steel wire braids covered by a polyurethane sleeve - providing the strength and abrasion resistance needed for repeated use in tough working environments.

Diameters available 0.25 and 0.38 (6.4 and 9.7mm), and connection types include 1/4 NPTF 3/8 NPTF and CH604.

A variety of lengths are available up to 50 ft (15 m), and the vinyl strain relief guard on both ends of hose helps to improve hose life and durability.

• Type: Hose
• Max Bar: 700
• Max PSI: 10000

• Product Group: Hoses, Pumps
• Product Line: Industrial Tools
• Series: H700
• SubTypes: Thermo-plastic Hose

• For demanding applications, featuring a 4:1 safety factor
• Maximum working pressure of 10,000 psi
• Outside jacket is polyurethane, to provide maximum abrasion resistance
• Exhibits low volumetric expansion under pressure to enhance overall system efficiency
• Vinyl strain relief guard on both ends of hose to improve life and durability on all models.

EP HB7206QB

H700-Series Hoses have a safety factor of 4:1 to provide the reassurance and reliability needed for demanding high-pressure applications.

Each hose contains two layers of steel wire braids covered by a polyurethane sleeve - providing the strength and abrasion resistance needed for repeated use in tough working environments.

Diameters available 0.25 and 0.38 (6.4 and 9.7mm), and connection types include 1/4 NPTF 3/8 NPTF and CH604.

A variety of lengths are available up to 50 ft (15 m), and the vinyl strain relief guard on both ends of hose helps to improve hose life and durability.

• Type: Hose
• Max Bar: 700
• Max PSI: 10000

• Product Group: Hoses, Pumps
• Product Line: Industrial Tools
• Series: H700
• SubTypes: Thermo-plastic Hose

• For demanding applications, featuring a 4:1 safety factor
• Maximum working pressure of 10,000 psi
• Outside jacket is polyurethane, to provide maximum abrasion resistance
• Exhibits low volumetric expansion under pressure to enhance overall system efficiency
• Vinyl strain relief guard on both ends of hose to improve life and durability on all models.

EP HC7206B

H700-Series Hoses have a safety factor of 4:1 to provide the reassurance and reliability needed for demanding high-pressure applications.

Each hose contains two layers of steel wire braids covered by a polyurethane sleeve - providing the strength and abrasion resistance needed for repeated use in tough working environments.

Diameters available 0.25 and 0.38 (6.4 and 9.7mm), and connection types include 1/4 NPTF 3/8 NPTF and CH604.

A variety of lengths are available up to 50 ft (15 m), and the vinyl strain relief guard on both ends of hose helps to improve hose life and durability.

• Type: Hose
• Max Bar: 700
• Max PSI: 10000

• Product Group: Hoses, Pumps
• Product Line: Industrial Tools
• Series: H700
• SubTypes: Thermo-plastic Hose

• For demanding applications, featuring a 4:1 safety factor
• Maximum working pressure of 10,000 psi
• Outside jacket is polyurethane, to provide maximum abrasion resistance
• Exhibits low volumetric expansion under pressure to enhance overall system efficiency
• Vinyl strain relief guard on both ends of hose to improve life and durability on all models.