ENERPAC S100272

EP PMB2

• Type: Press Accessory

• Product Group: Presses
• Product Line: Industrial Tools
• Series: A
• SubTypes: Press Pump Mounting Bracket

• Heavy duty steel brackets to allow conversion to one of the Enerpac Power Sources to power your press.
• Both mounting brackets are pre-drilled to accept a number of different pump models

EP PME10427K

• Type: Service Kit

• Product Group: Pumps
• Series: PME repair kit
• SubTypes: Repair Kit

EP PP179017

• Type: Service Kit

• SubTypes: Retaining Ring

EP PRASA10016L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 16
• Stroke MM: 406
• SubTypes: POW'R-RISER Jack Pneumatic

• Capacity Imperial Tons: 100
• Capacity KN: 889

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS60, PRU13, PRU14, PRU110, PRUS126, PRE5, PRE7, PRE9, PRE11, PRE14, PRE18, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PRASA10027L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 27
• Stroke MM: 686
• SubTypes: POW'R-RISER Jack Pneumatic

• Capacity Imperial Tons: 100
• Capacity KN: 889

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS60, PRU13, PRU14, PRU110, PRUS137, PRE5, PRE7, PRE9, PRE11, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PRASA15027L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 26.5
• Stroke MM: 673
• SubTypes: POW'R-RISER Jack Pneumatic

• Capacity Imperial Tons: 150
• Capacity KN: 1333

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS150, PRU151, PRU153, PRU155, PRU1510, PRUS1537, PRE5, PRE7, PRE9, PRE11, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PTW1000C

• Type: Torque Wrench

• Product Group: Torque Wrenches, Torque Wrench Pumps
• Product Line: Bolting Tools
• Series: PTW
• SubTypes: Pneumatic Torque Wrench with FRL

• High speed continuous rotation for constant torque output
• Low friction planetary gearbox design minimizes wear and extends uptime
• Ergonomic, low vibration design reduces fatigue and the risk of vibration related injuries for the operator
• Low noise air motor provides quiet, consistent performance for indoor and outdoor applications
• Provided with standard reaction arm; wide assortment of custom arms and accessories are available
• Available with or without Filter-Regulator-Lubricator (FRL)
• Unique calibration certificate provided with each tool

• Set Includes: RATWS, FRL120C
• Accessories: ED6TWS, ED12TWS, ED18TWS, RATWS, ERATWS, SLRATWS, DSATWS, SRATWS, BLTWS

EP PTW2000C

• Type: Torque Wrench

• Product Group: Torque Wrenches, Torque Wrench Pumps
• Product Line: Bolting Tools
• Series: PTW
• SubTypes: Pneumatic Torque Wrench with FRL

• High speed continuous rotation for constant torque output
• Low friction planetary gearbox design minimizes wear and extends uptime
• Ergonomic, low vibration design reduces fatigue and the risk of vibration related injuries for the operator
• Low noise air motor provides quiet, consistent performance for indoor and outdoor applications
• Provided with standard reaction arm; wide assortment of custom arms and accessories are available
• Available with or without Filter-Regulator-Lubricator (FRL)
• Unique calibration certificate provided with each tool

• Set Includes: RATWS, FRL120C
• Accessories: ED6TWS, ED12TWS, ED18TWS, RATWS, ERATWS, SLRATWS, DSATWS, SRATWS, BLTWS

EP PUD1100B

PU Series electric over hydraulic pumps combine economy with high-performance - ideal for intermittent use when working with small to medium size cylinders and other hydraulic tools.

All models in the series are 2-speed for enhanced productivity, and each is supplied with a 10 ft (3 m) cord and control pendant for operator safety. The high-strength molded shroud with integral handle protects the motor from contamination and damage in industrial environments.

Within the PU Series is a selection of pumps that offer a choice of reservoir capacities, valve functions and voltage.

PUD1100 Series

• For advance and retract of single-acting cylinders
• For applications not requiring load holding
• Ideal for punching applications

PUD1300 Series

• Providing advance, hold, and retract of single-acting cylinders
• Ideal for applications requiring load holding
• For applications requiring solenoid valves

PUJ-Series

• Manual valves provide advance, hold, and retract operation
• 3 and 4-way valves for single or double-acting cylinders

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: PU
• SubTypes: Electric Pump - Economy

• The economic choice for small to medium sized tools.
• Lightweight, compact, and portable.
• Two-speed operation reduces cycle times for improved productivity.
• Ideal for intermittent duty cycles.
• Works well with long extension cords or generator-driven electrical power supplies.
• 115 VAC 50/60-cycle universal motor will operate under poor voltage supply.
• 24 VAC remote motor control with 10 ft (3 m) cord for operator safety.
• Starts under full load.
• High-strength shroud with integral handle protects the motor from contamination and damage.

• Spare Part(s): PUD1100BK

EP PREMB10016L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 16
• Stroke MM: 406
• SubTypes: POW'R-RISER Jack Electric

• Capacity Imperial Tons: 100
• Capacity KN: 889

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS60, PRU13, PRU14, PRU110, PRUS126, PRE5, PRE7, PRE9, PRE11, PRE14, PRE18, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PRAMA10016L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 16
• Stroke MM: 406
• SubTypes: POW'R-RISER Jack Pneumatic

• Capacity Imperial Tons: 100
• Capacity KN: 889

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS60, PRU13, PRU14, PRU110, PRUS126, PRE5, PRE7, PRE9, PRE11, PRE14, PRE18, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PUD1100BK

• Type: Service Kit

• Product Group: Pumps
• Series: PU (service kit)
• SubTypes: Repair Kit

EP PUD1300B

PU Series electric over hydraulic pumps combine economy with high-performance - ideal for intermittent use when working with small to medium size cylinders and other hydraulic tools.

All models in the series are 2-speed for enhanced productivity, and each is supplied with a 10 ft (3 m) cord and control pendant for operator safety. The high-strength molded shroud with integral handle protects the motor from contamination and damage in industrial environments.

Within the PU Series is a selection of pumps that offer a choice of reservoir capacities, valve functions and voltage.

PUD1100 Series

• For advance and retract of single-acting cylinders
• For applications not requiring load holding
• Ideal for punching applications

PUD1300 Series

• Providing advance, hold, and retract of single-acting cylinders
• Ideal for applications requiring load holding
• For applications requiring solenoid valves

PUJ-Series

• Manual valves provide advance, hold, and retract operation
• 3 and 4-way valves for single or double-acting cylinders

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: PU
• SubTypes: Electric Pump - Economy

• The economic choice for small to medium sized tools.
• Lightweight, compact, and portable.
• Two-speed operation reduces cycle times for improved productivity.
• Ideal for intermittent duty cycles.
• Works well with long extension cords or generator-driven electrical power supplies.
• 115 VAC 50/60-cycle universal motor will operate under poor voltage supply.
• 24 VAC remote motor control with 10 ft (3 m) cord for operator safety.
• Starts under full load.
• High-strength shroud with integral handle protects the motor from contamination and damage.

• Spare Part(s): PUD1100BK

EP PUJ1200BK1

• Type: Service Kit

• Product Group: Pumps
• Series: PU (service kit)
• SubTypes: Repair Kit

EP PUJ1400BK

• Type: Service Kit

• Product Group: Pumps
• Series: PU (service kit)
• SubTypes: Repair Kit

EP PUJ1400B

PU Series electric over hydraulic pumps combine economy with high-performance - ideal for intermittent use when working with small to medium size cylinders and other hydraulic tools.

All models in the series are 2-speed for enhanced productivity, and each is supplied with a 10 ft (3 m) cord and control pendant for operator safety. The high-strength molded shroud with integral handle protects the motor from contamination and damage in industrial environments.

Within the PU Series is a selection of pumps that offer a choice of reservoir capacities, valve functions and voltage.

PUD1100 Series

• For advance and retract of single-acting cylinders
• For applications not requiring load holding
• Ideal for punching applications

PUD1300 Series

• Providing advance, hold, and retract of single-acting cylinders
• Ideal for applications requiring load holding
• For applications requiring solenoid valves

PUJ-Series

• Manual valves provide advance, hold, and retract operation
• 3 and 4-way valves for single or double-acting cylinders

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: PU
• SubTypes: Electric Pump - Economy

• The economic choice for small to medium sized tools.
• Lightweight, compact, and portable.
• Two-speed operation reduces cycle times for improved productivity.
• Ideal for intermittent duty cycles.
• Works well with long extension cords or generator-driven electrical power supplies.
• 115 VAC 50/60-cycle universal motor will operate under poor voltage supply.
• 24 VAC remote motor control with 10 ft (3 m) cord for operator safety.
• Starts under full load.
• High-strength shroud with integral handle protects the motor from contamination and damage.

• Spare Part(s): PUJ1400BK

EP R102

Simplex R-Series Single Acting Hydraulic Cylinders are the durable, reliable, and versatile choice for general purpose industrial use. With a vast range of cylinder tonnages and strokes available it's easy to find a cylinder perfectly matched to your application.

Threaded collars offer versatility in fixturing to give you many more application possibilities. Included inside R Series Cylinders is a positive stop to limit piston travel at the end of the stroke, adding extra strength and safety to your cylinder, and cylinder life is extended by the wiper seal.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: R
• Stroke Inches: 2.19
• Stroke MM: 55.6
• SubTypes: General Purpose Cylinder

• Capacity Imperial Tons: 10
• Capacity KN: 89,0

• Single acting with heavy-duty internal retraction spring
• Solid and plated piston resists scoring & corrosion
• Heat treated grooved saddles are provided as standard
• Stop ring limits piston travel at the end of the stroke to prevent blow-out
• High flow couplers are plated to resist corrosion
• Polyurethane wipers clean the piston surface during retraction - protecting the inner cylinder assembly from dirt, moisture, and other contaminants.
• Meets ANSI/ASME B30.1 Safety Standards
• Load tested under 125% of the nominal capacity
• For working pressures up to 10,000 psi (700 bar)

• Accessories: BA10, 18348, ATS10, BR10, BCR10, BC10

EP R515245-2

• Type: Service Kit

• SubTypes: Plug

EP RA106

• Type: Hydraulic Cylinders

• Product Group: Cylinders and Jacks

EP R57

Simplex R-Series Single Acting Hydraulic Cylinders are the durable, reliable, and versatile choice for general purpose industrial use. With a vast range of cylinder tonnages and strokes available it's easy to find a cylinder perfectly matched to your application.

Threaded collars offer versatility in fixturing to give you many more application possibilities. Included inside R Series Cylinders is a positive stop to limit piston travel at the end of the stroke, adding extra strength and safety to your cylinder, and cylinder life is extended by the wiper seal.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: R
• Stroke Inches: 7.18
• Stroke MM: 182.4
• SubTypes: General Purpose Cylinder

• Capacity Imperial Tons: 5
• Capacity KN: 44,5

• Single acting with heavy-duty internal retraction spring
• Solid and plated piston resists scoring & corrosion
• Heat treated grooved saddles are provided as standard
• Stop ring limits piston travel at the end of the stroke to prevent blow-out
• High flow couplers are plated to resist corrosion
• Polyurethane wipers clean the piston surface during retraction - protecting the inner cylinder assembly from dirt, moisture, and other contaminants.
• Meets ANSI/ASME B30.1 Safety Standards
• Load tested under 125% of the nominal capacity
• For working pressures up to 10,000 psi (700 bar)

• Accessories: 18347, BCR5, BR5

EP RAC20K50

• Type: Service Kit

• SubTypes: Repair Kit

EP RAC50K50

• Type: Service Kit

• SubTypes: Repair Kit

EP QDH120

• Type: Hydraulic Cylinders
• Max Bar: 350
• Max PSI: 5000

• Product Group: Cylinders and Jacks
• Product Line: Work Holding Tools
• Series: QDH
• Stroke Inches: 0.32
• Stroke MM: 8.1
• SubTypes: Workholding Hollow Plunger Cylinder

• Load can be attached to either end of the cylinder, providing a choice of push or pull actions - both realizing full cylinder capacity
• Very high cylinder capacities contained within small dimensions allow compact fixture designs
• Spring return operation allows for easy unloading of the workpiece
• Threaded collars and base mounting holes allow mounting flexibility, including table-top surfaces and T-slots
• Nickel-plated plungers, plunger wipers and internal venting prevent corrosion and support longer operation life on allHCS models

EP RACD3010

• Technical coating reduces wear & corrosion.
• Steel piston for protection against load damage.
• Chrome plated sleeve for extra protection.
• Stop rings for piston blow-out protection.
• Rod wiper protects inner cylinder from dirt.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: RACD
• Stroke Inches: 10
• Stroke MM: 254
• SubTypes: Aluminum Center Hole Cylinder

• Capacity Imperial Tons: 30
• Capacity KN: 266,9

EP RACD10010

• Technical coating reduces wear & corrosion.
• Steel piston for protection against load damage.
• Chrome plated sleeve for extra protection.
• Stop rings for piston blow-out protection.
• Rod wiper protects inner cylinder from dirt.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: RACD
• Stroke Inches: 10
• Stroke MM: 254
• SubTypes: Aluminum Center Hole Cylinder

• Capacity Imperial Tons: 100
• Capacity KN: 889,6

EP R59

Simplex R-Series Single Acting Hydraulic Cylinders are the durable, reliable, and versatile choice for general purpose industrial use. With a vast range of cylinder tonnages and strokes available it's easy to find a cylinder perfectly matched to your application.

Threaded collars offer versatility in fixturing to give you many more application possibilities. Included inside R Series Cylinders is a positive stop to limit piston travel at the end of the stroke, adding extra strength and safety to your cylinder, and cylinder life is extended by the wiper seal.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: R
• Stroke Inches: 9.18
• Stroke MM: 233.2
• SubTypes: General Purpose Cylinder

• Capacity Imperial Tons: 5
• Capacity KN: 44,5

• Single acting with heavy-duty internal retraction spring
• Solid and plated piston resists scoring & corrosion
• Heat treated grooved saddles are provided as standard
• Stop ring limits piston travel at the end of the stroke to prevent blow-out
• High flow couplers are plated to resist corrosion
• Polyurethane wipers clean the piston surface during retraction - protecting the inner cylinder assembly from dirt, moisture, and other contaminants.
• Meets ANSI/ASME B30.1 Safety Standards
• Load tested under 125% of the nominal capacity
• For working pressures up to 10,000 psi (700 bar)

• Accessories: 18347, BCR5, BR5

EP RACH1006005

• Type: Service Kit

• SubTypes: Tube

EP RACH1006

RACH-Series Hollow Plunger Hydraulic Cylinders (sometimes called center-hole cylinders) feature a hollow plunger with an internal thread to allow fixing to the component to be pulled. This makes them the ideal choice for when you need a lighter, more portable cylinder for applications such as tensioning, testing, pulling, and lifting. Each RACH Cylinder is rated for up to 10,000 psi (700 bar) and compliant with ASME B30.1.

Each RACH Cylinder is single-acting and uses a high-strength return spring for rapid retraction. All are equipped with bolt-on hardened steel saddles and a steel base plate for increased durability.

Aluminum is not only lightweight, but also inherently less corrosive than steel, which makes it a great material for use in many caustic environments. For enhanced protection, RACH Aluminum Cylinders are finished with an anodized hard coat finish to resist damage and extend cylinder life.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RACH
• Stroke Inches: 5.91
• Stroke MM: 150
• SubTypes: Aluminum Hollow Plunger Cylinder

• Hollow plunger design allows for both pull and push forces
• Composite bearings increase cylinder life and side load resistance
• Hard coat finish on all surfaces resists damage and extends cylinder life
• Handles included on all models
• Floating center tube increases seal life
• Steel baseplate and saddle for protection against load-induced damage
• Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
• High-strength return spring for rapid cylinder retraction
• CR400 coupler and dustcap included on all models
• All cylinders meet ASME B-30.1 standards

EP RACH1006040

• Type: Service Kit

• SubTypes: Plunger Kit

EP RACD5010

• Technical coating reduces wear & corrosion.
• Steel piston for protection against load damage.
• Chrome plated sleeve for extra protection.
• Stop rings for piston blow-out protection.
• Rod wiper protects inner cylinder from dirt.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: RACD
• Stroke Inches: 10
• Stroke MM: 254
• SubTypes: Aluminum Center Hole Cylinder

• Capacity Imperial Tons: 50
• Capacity KN: 444,8

EP RACH100K50

• Type: Service Kit

• SubTypes: Repair Kit

EP RACH2010

RACH-Series Hollow Plunger Hydraulic Cylinders (sometimes called center-hole cylinders) feature a hollow plunger with an internal thread to allow fixing to the component to be pulled. This makes them the ideal choice for when you need a lighter, more portable cylinder for applications such as tensioning, testing, pulling, and lifting. Each RACH Cylinder is rated for up to 10,000 psi (700 bar) and compliant with ASME B30.1.

Each RACH Cylinder is single-acting and uses a high-strength return spring for rapid retraction. All are equipped with bolt-on hardened steel saddles and a steel base plate for increased durability.

Aluminum is not only lightweight, but also inherently less corrosive than steel, which makes it a great material for use in many caustic environments. For enhanced protection, RACH Aluminum Cylinders are finished with an anodized hard coat finish to resist damage and extend cylinder life.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RACH
• Stroke Inches: 9.84
• Stroke MM: 250
• SubTypes: Aluminum Hollow Plunger Cylinder

• Hollow plunger design allows for both pull and push forces
• Composite bearings increase cylinder life and side load resistance
• Hard coat finish on all surfaces resists damage and extends cylinder life
• Handles included on all models
• Floating center tube increases seal life
• Steel baseplate and saddle for protection against load-induced damage
• Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
• High-strength return spring for rapid cylinder retraction
• CR400 coupler and dustcap included on all models
• All cylinders meet ASME B-30.1 standards

EP RACH20K50

• Type: Service Kit

• SubTypes: Repair Kit

EP RACH602005

• Type: Service Kit

• SubTypes: Tube

EP RACL504

RACL-Series Aluminum Cylinders include a lock nut that gives the reassurance of safe mechanical load holding for extended periods. Each cylinder is single-acting with a high-strength return spring for rapid retraction. The integral stop ring prevents plunger over-travel. All are equipped with bolt-on hardened steel saddles and a steel base plate for increased durability.

Enerpac RACL Lock Nut Aluminum Hydraulic Cylinders can change the way you think about your cylinder applications. With approximately half of the weight of equivalent steel models, they combine an impressive power to weight ratio with the convenience of easier transport and positioning. RACL cylinders are rated for 10,000 psi (700 bar) and comply with ASME B30.1.

Aluminum is not only lightweight, but also inherently less corrosive than steel, which makes it a great material for use in many caustic environments. For enhanced protection, Enerpac RACL Aluminum Cylinders are finished with an anodized hard coat finish to resist damage and extend cylinder life.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RACL
• Stroke Inches: 3.94
• Stroke MM: 100
• SubTypes: Aluminum Lock Nut Cylinder

• Aluminum Lock Nut provides mechanical load holding for extended periods
• Hardened steel stop ring increases cylinder life and resistance to side-loads of up to 5%
• Hard coat finish on all surfaces resists damage and extends cylinder life
• Composite bearings increase cylinder life and side load resistance
• Handles included on all models
• Steel base plate and saddle for protection against load-induced damage
• Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
• High-strength return spring for rapid cylinder retraction
• CR400 coupler and dustcap included on all models
• All cylinders meet ASME B-30.1 standards

• Accessories: CATS50

EP RACL204

RACL-Series Aluminum Cylinders include a lock nut that gives the reassurance of safe mechanical load holding for extended periods. Each cylinder is single-acting with a high-strength return spring for rapid retraction. The integral stop ring prevents plunger over-travel. All are equipped with bolt-on hardened steel saddles and a steel base plate for increased durability.

Enerpac RACL Lock Nut Aluminum Hydraulic Cylinders can change the way you think about your cylinder applications. With approximately half of the weight of equivalent steel models, they combine an impressive power to weight ratio with the convenience of easier transport and positioning. RACL cylinders are rated for 10,000 psi (700 bar) and comply with ASME B30.1.

Aluminum is not only lightweight, but also inherently less corrosive than steel, which makes it a great material for use in many caustic environments. For enhanced protection, Enerpac RACL Aluminum Cylinders are finished with an anodized hard coat finish to resist damage and extend cylinder life.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RACL
• Stroke Inches: 3.94
• Stroke MM: 100
• SubTypes: Aluminum Lock Nut Cylinder

• Aluminum Lock Nut provides mechanical load holding for extended periods
• Hardened steel stop ring increases cylinder life and resistance to side-loads of up to 5%
• Hard coat finish on all surfaces resists damage and extends cylinder life
• Composite bearings increase cylinder life and side load resistance
• Handles included on all models
• Steel base plate and saddle for protection against load-induced damage
• Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
• High-strength return spring for rapid cylinder retraction
• CR400 coupler and dustcap included on all models
• All cylinders meet ASME B-30.1 standards

EP RAR1004

RAR-Series Double Acting Hydraulic Cylinders provide a rapid and more controlled plunger retraction than spring return or load return types. The hydraulic return method continues to work effectively regardless of hose lengths and system losses, maintaining efficiency and productivity. Each RAR Cylinder is rated for up to 10,000 psi (700 bar) and compliant with ASME B30.1.

The aluminum construction of RAR Cylinders means they are not only lightweight, but also less corrosive than steel equivalents. This helps to maintain durability in many caustic environments. For enhanced protection, RAR Aluminum Cylinders are finished with an anodized hard coat finish to resist damage and extend cylinder life. Handles featured on all models enhance their portability.

Each RAR Cylinder is equipped with a bolt-on hardened steel saddle and a steel base plate for increased durability. Optional Tilt Saddles can help to support the load evenly and alleviate unwanted side-load.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RAR
• Stroke Inches: 3.94
• Stroke MM: 100
• SubTypes: Aluminum Cylinder

• Double-acting for rapid retraction, regardless of hose lengths and system losses
• Composite bearings increase cylinder life and side load resistance
• Hard coat finish on all surfaces resists damage and extends cylinder life
• Handles included on all models
• Steel base plate and saddle for protection against load- induced damage
• Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
• Built-in safety valve prevents accidental over-pressurization

• Accessories: CATS101

EP RAL502

Simplex RAL Series Aluminum Hydraulic Cylinders feature lock nut that provide the reassurance of safe mechanical load holding for extended periods. These are approximately half the weight of steel equivalents and are expertly engineered to withstand tough applications in harsh conditions.

Aluminum is not only lighter, but also inherently less corrosive than steel, which makes it a great material for use in many caustic environments. A carrying handle provided on all RAL cylinders also enhance portability.

Inside the cylinder is a high-strength return spring for plunger retraction and stop rings for protection against blow out. The cylinder exterior is finished with an anodized hard coat to extend cylinder life, and a wiper protects the inner cylinder assembly from dirt, moisture, and other contaminants.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: RAL
• Stroke Inches: 2
• Stroke MM: 50.8
• SubTypes: Aluminum Locknut Cylinder

• Capacity Imperial Tons: 50
• Capacity KN: 444,8

• Approximately half the weight of steel cylinders
• Lock nut for mechanical load holding for extended periods
• Heavy duty spring delivers fast and full retraction
• Hard anodized coating reduces wear and corrosion
• Stop rings prevent piston blow-out
• Wiper protects inner cylinder from dirt.
• Meets ANSI/ASME B30.1 Safety Standards
• Load tested under 125% of the nominal capacity
• For working pressures up to 10,000 psi (700 bar)

EP RAR1006040

• Type: Service Kit

• SubTypes: Plunger Kit

EP RAR100K50

• Type: Service Kit

• SubTypes: Repair Kit

EP RARH3010

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10150

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RARH
• Stroke Inches: 9.84
• Stroke MM: 250
• SubTypes: Aluminum Hollow Plunger Cylinder

• Lighter and shorter collapsed height than equivalent RACH single-acting models
• Double-acting for rapid retraction, regardless of hose lengths or system losses
• Built-in safety valve prevents accidental overpressurization
• Hollow plunger design allows for both pull and push forces
• Composite bearings increase cylinder life and side load resistance
• Hard coat finish on all surfaces resists damage and extends cylinder life
• Handles included on all models
• Floating center tube increases seal life
• Steel baseplate and saddle for protection against load-induced damage
• Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
• CR400 coupler and dust cap included on all models
• All cylinders meet ASME B-30.1 standards

• Accessories: HP3015

EP RARH606

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10150

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RARH
• Stroke Inches: 5.91
• Stroke MM: 150
• SubTypes: Aluminum Hollow Plunger Cylinder

• Lighter and shorter collapsed height than equivalent RACH single-acting models
• Double-acting for rapid retraction, regardless of hose lengths or system losses
• Built-in safety valve prevents accidental overpressurization
• Hollow plunger design allows for both pull and push forces
• Composite bearings increase cylinder life and side load resistance
• Hard coat finish on all surfaces resists damage and extends cylinder life
• Handles included on all models
• Floating center tube increases seal life
• Steel baseplate and saddle for protection against load-induced damage
• Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
• CR400 coupler and dust cap included on all models
• All cylinders meet ASME B-30.1 standards

• Accessories: HP5016

EP RC10010

RC-TRIO is the next generation of the legendary Enerpac RC-Series single acting hydraulic cylinders. These hydraulic jacks include many advanced features to ensure superior durability, versatility, and productivity.

A pre-tensioned spring provides fast plunger retraction and enhanced productivity. The robust bearing system features composite wear bands and a hardened stop ring to resist side-load which minimizes damage and repairs. The plunger wiper, high-grade polyethylene seals and tough external finishes also help towards an extended service life.

With so many hydraulic cylinder models to choose from, we’re confident you’ll find the perfect match for your applications, and if you already own prior RC-Series cylinders, the good news is the new cylinders share the same familiar dimensions and threads for full compatibility.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RC
• Stroke Inches: 10.25
• Stroke MM: 260
• SubTypes: General Purpose Cylinder

• Bearing system with composite wear bands for optimal sideload resistance
• Strengthened stop ring improves durability and side load resistance
• Trio Hybrid pre-tensioned spring system provides faster retraction
• High-grade polyethylene seals for low wear and long service life
• Plunger wiper reduces contamination, extending cylinder life.
• Collar and plunger threads and base mounting holes enable easy fixturing (on most models)
• Standard certified lifting eyes on cylinder models above 55 lbs. (25 kg) weight.
• Interchangeable with optional CHM6 carrying handle
• Designed for use in all positions
• Baked enamel finish for increased corrosion resistance
• Includes CR400 coupler, dust cap and collar thread protector
• RC-Series model numbers, external dimensions and threads remain unchanged from prior RC Series cylinders

• Spare Part(s): RC100044, HCL50045, RC10010040, RC100NK0, RC100NKS3, RC100NKS, RC100NKB1, RC100NKB2, RC100NKB3, RC100NKB4, RC100NKW
• Accessories: CATS100, CHM6

EP RC10044

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Stop Ring

EP RC1006K

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RC1010

RC-TRIO is the next generation of the legendary Enerpac RC-Series single acting hydraulic cylinders. These hydraulic jacks include many advanced features to ensure superior durability, versatility, and productivity.

A pre-tensioned spring provides fast plunger retraction and enhanced productivity. The robust bearing system features composite wear bands and a hardened stop ring to resist side-load which minimizes damage and repairs. The plunger wiper, high-grade polyethylene seals and tough external finishes also help towards an extended service life.

With so many hydraulic cylinder models to choose from, we’re confident you’ll find the perfect match for your applications, and if you already own prior RC-Series cylinders, the good news is the new cylinders share the same familiar dimensions and threads for full compatibility.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RC
• Stroke Inches: 10.13
• Stroke MM: 257
• SubTypes: General Purpose Cylinder

• Bearing system with composite wear bands for optimal sideload resistance
• Strengthened stop ring improves durability and side load resistance
• Trio Hybrid pre-tensioned spring system provides faster retraction
• High-grade polyethylene seals for low wear and long service life
• Plunger wiper reduces contamination, extending cylinder life.
• Collar and plunger threads and base mounting holes enable easy fixturing (on most models)
• Standard certified lifting eyes on cylinder models above 55 lbs. (25 kg) weight.
• Interchangeable with optional CHM6 carrying handle
• Designed for use in all positions
• Baked enamel finish for increased corrosion resistance
• Includes CR400 coupler, dust cap and collar thread protector
• RC-Series model numbers, external dimensions and threads remain unchanged from prior RC Series cylinders

• Spare Part(s): RC106044, RC1010040, RC10NK0, RC10K35, RC10NKS, RC10NKB2, RC10NKB3, RC10NKW
• Accessories: A92, A102G, CATS12, JBI10, RB10, AW102, REB10, REP10

EP RC102K

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Seal Kit

EP RC10K52

• Type: Service Kit

• SubTypes: Repair Kit

EP RC10K71

• Type: Service Kit

• SubTypes: Repair Kit

EP RC10K72

• Type: Service Kit

• SubTypes: Repair Kit

EP RC10NK0

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RC15044

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Stop Ring

EP RC15K1

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RC15K31

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Spring Kit

EP RC15K32

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Spring Kit

EP RC15K51

• Type: Service Kit

• SubTypes: Repair Kit

EP RC15K71

• Type: Service Kit

• SubTypes: Repair Kit

EP RC15NK0

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RC25K51

• Type: Service Kit

• SubTypes: Repair Kit

EP RC25K52

• Type: Service Kit

• SubTypes: Repair Kit

EP RC25K71

• Type: Service Kit

• SubTypes: Repair Kit

EP RC25K72

• Type: Service Kit

• SubTypes: Repair Kit

EP RC5010

RC-TRIO is the next generation of the legendary Enerpac RC-Series single acting hydraulic cylinders. These hydraulic jacks include many advanced features to ensure superior durability, versatility, and productivity.

A pre-tensioned spring provides fast plunger retraction and enhanced productivity. The robust bearing system features composite wear bands and a hardened stop ring to resist side-load which minimizes damage and repairs. The plunger wiper, high-grade polyethylene seals and tough external finishes also help towards an extended service life.

With so many hydraulic cylinder models to choose from, we’re confident you’ll find the perfect match for your applications, and if you already own prior RC-Series cylinders, the good news is the new cylinders share the same familiar dimensions and threads for full compatibility.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RC
• Stroke Inches: 10.25
• Stroke MM: 260
• SubTypes: General Purpose Cylinder

• Bearing system with composite wear bands for optimal sideload resistance
• Strengthened stop ring improves durability and side load resistance
• Trio Hybrid pre-tensioned spring system provides faster retraction
• High-grade polyethylene seals for low wear and long service life
• Plunger wiper reduces contamination, extending cylinder life.
• Collar and plunger threads and base mounting holes enable easy fixturing (on most models)
• Standard certified lifting eyes on cylinder models above 55 lbs. (25 kg) weight.
• Interchangeable with optional CHM6 carrying handle
• Designed for use in all positions
• Baked enamel finish for increased corrosion resistance
• Includes CR400 coupler, dust cap and collar thread protector
• RC-Series model numbers, external dimensions and threads remain unchanged from prior RC Series cylinders

• Spare Part(s): RC50044, HCL50045, RC5010040, RC50NK0, RC50NKS1, RC50NKS, RC50NKB1, RC50NKB2, RC50NKW
• Accessories: CATS100, JBI50, CHM6

EP RC506K

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RC50K

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RC50K1

• Type: Service Kit

• SubTypes: Repair Kit

EP RC50K51

• Type: Service Kit

• SubTypes: Repair Kit

EP RC53K

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RC55

RC-TRIO is the next generation of the legendary Enerpac RC-Series single acting hydraulic cylinders. These hydraulic jacks include many advanced features to ensure superior durability, versatility, and productivity.

A pre-tensioned spring provides fast plunger retraction and enhanced productivity. The robust bearing system features composite wear bands and a hardened stop ring to resist side-load which minimizes damage and repairs. The plunger wiper, high-grade polyethylene seals and tough external finishes also help towards an extended service life.

With so many hydraulic cylinder models to choose from, we’re confident you’ll find the perfect match for your applications, and if you already own prior RC-Series cylinders, the good news is the new cylinders share the same familiar dimensions and threads for full compatibility.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RC
• Stroke Inches: 5
• Stroke MM: 127
• SubTypes: General Purpose Cylinder

• Bearing system with composite wear bands for optimal sideload resistance
• Strengthened stop ring improves durability and side load resistance
• Trio Hybrid pre-tensioned spring system provides faster retraction
• High-grade polyethylene seals for low wear and long service life
• Plunger wiper reduces contamination, extending cylinder life.
• Collar and plunger threads and base mounting holes enable easy fixturing (on most models)
• Standard certified lifting eyes on cylinder models above 55 lbs. (25 kg) weight.
• Interchangeable with optional CHM6 carrying handle
• Designed for use in all positions
• Baked enamel finish for increased corrosion resistance
• Includes CR400 coupler, dust cap and collar thread protector
• RC-Series model numbers, external dimensions and threads remain unchanged from prior RC Series cylinders

• Spare Part(s): RC5044, RC55040, RC5NK0, RC5K33, RC5NKS, RC5NKB1, RC5NKB2, RC5NKW1
• Accessories: A53F, A53G, RB5, AW51, AW53, REB5, REP5

EP RC5K30

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Spring Kit

EP RC603A

Simplex RC Series Hollow Plunger Hydraulic Cylinders offer the versatility needed to take on a wide range of applications. The hollow plunger design allows bars or rods to be pulled through the inside bore to enable pulling and pushing applications - ideal for tensioning cables, bolts, and pulling sleeves or bearings.

Inside the cylinder is a high-strength return spring for plunger retraction and stop rings for blow out protection. The cylinder exterior is finished with an enamel coating to extend cylinder life, and a wiper protects the inner cylinder assembly from dirt, moisture, and other contaminants.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: RC - Simplex
• Stroke Inches: 3
• Stroke MM: 76.2
• SubTypes: Center Hole Cylinder

• Capacity Imperial Tons: 60
• Capacity KN: 533,8

• Induction hardened piston rod for added strength eliminates the need for a saddle.
• Collar threads for easy fixing of components.
• Hollow plunger design allows for both push & pull forces.
• Large center hole for greater flexibility.
• Heavy duty spring delivers fast and full retraction
• Stop rings prevent piston blow-out
• Wiper protects inner cylinder from dirt.
• Meets ANSI/ASME B30.1 Safety Standards
• Load tested under 125% of the nominal capacity
• For working pressures up to 10,000 psi (700 bar)

EP RC756K

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RCH1003

RCH-Series Hollow Plunger Cylinders offer versatility in testing, maintenance, and tensioning applications. The hollow plunger design allows for push, pull or lifting applications.

Enerpac cylinders are built to withstand tough conditions and demanding applications. These RCH cylinders have a baked enamel finish to resist corrosion. The center hole design has base holes and collar threads for easy fixturing. For models over 20 tons, the RCH series has nickel-plated floating center tube to reduce side load damage and increase the product life.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RCH
• Stroke inch: 3
• Stroke MM: 76
• SubTypes: Hollow Plunger Cylinder

• Hollow plunger design allows for both pull and push forces
• Single-acting spring return
• Nickel-plated, floating center tube on models over 20 tons increases product life
• Baked enamel finish for increased corrosion resistance
• Collar threads for easy fixturing
• Features CR400 Coupler

• Set Includes: CR400
• Spare Part(s): RCH1003K
• Accessories: HP10016

EP RCH121K1

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RCH202

RCH-Series Hollow Plunger Cylinders offer versatility in testing, maintenance, and tensioning applications. The hollow plunger design allows for push, pull or lifting applications.

Enerpac cylinders are built to withstand tough conditions and demanding applications. These RCH cylinders have a baked enamel finish to resist corrosion. The center hole design has base holes and collar threads for easy fixturing. For models over 20 tons, the RCH series has nickel-plated floating center tube to reduce side load damage and increase the product life.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RCH
• Stroke Inches: 2
• Stroke MM: 49
• SubTypes: Hollow Plunger Cylinder

• Hollow plunger design allows for both pull and push forces
• Single-acting spring return
• Nickel-plated, floating center tube on models over 20 tons increases product life
• Baked enamel finish for increased corrosion resistance
• Collar threads for easy fixturing
• Features CR400 Coupler

• Set Includes: CR400
• Spare Part(s): RCH202K, CF707110, CB894045, RCH202KV1
• Accessories: HP202

EP RCH202K

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RCH302K2

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RCH603K

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RCH302

RCH-Series Hollow Plunger Cylinders offer versatility in testing, maintenance, and tensioning applications. The hollow plunger design allows for push, pull or lifting applications.

Enerpac cylinders are built to withstand tough conditions and demanding applications. These RCH cylinders have a baked enamel finish to resist corrosion. The center hole design has base holes and collar threads for easy fixturing. For models over 20 tons, the RCH series has nickel-plated floating center tube to reduce side load damage and increase the product life.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RCH
• Stroke Inches: 2.5
• Stroke MM: 64
• SubTypes: Hollow Plunger Cylinder

• Hollow plunger design allows for both pull and push forces
• Single-acting spring return
• Nickel-plated, floating center tube on models over 20 tons increases product life
• Baked enamel finish for increased corrosion resistance
• Collar threads for easy fixturing
• Features CR400 Coupler

• Set Includes: CR400
• Spare Part(s): RCH302K2, CH259110, CF698045, RWH302KV
• Accessories: HP3015

EP RCH603K1

• Type: Service Kit

• SubTypes: Repair Kit

EP RCS1002K

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RCS302

RCS-Series Low Profile Hydraulic Cylinders provide superior durability, performance longevity, safety, and quality in a compact and convenient footprint. These low profile hydraulic jacks are the perfect choice for general lifting and production applications where space is limited or constrained. A low collapsed height, short stroke, and solid construction enables safety and stability in both vertical and horizontal orientations.

Many low-profile hydraulic cylinders rely on the weight of the load to retract the plunger. RCS cylinders are different and include a powerful return spring, which is faster, convenient, and more productive. The entire RCS cylinder range is rated for high-pressure; 10,000 psi (700 bar).

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RCS
• Stroke Inches: 2.44
• Stroke MM: 62
• SubTypes: Low Height Cylinder

• Lightweight, low profile design for use in confined spaces
• Baked enamel finish for increased corrosion resistance
• Plunger wiper reduces contamination, extending cylinder life
• CR-400 coupler and dust cap included on all models
• Grooved plunger end with threaded holes for mounting tilt saddles
• Plated steel plungers
• Single-acting spring return

• Spare Part(s): RCS302K, DC5215900, RCS302KV
• Accessories: CATS53

EP RCS302K

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RCS502K

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP RD1610

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000
• Min Bar: 35

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools, Work Holding Tools
• Series: RD
• Stroke Inches: 10.25
• Stroke MM: 260
• SubTypes: General Purpose Cylinder

• Designed for long life, the best choice for production applications
• Unique mounting configurations simplify fixturing
• Baked enamel finish for increased corrosion resistance
• Double-acting operation develops force in both directions, providing maximum versatility
• Plunger wiper reduces contamination, extending cylinder life

• Accessories: AD181, AD182, AD183, AD152

EP RD166

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000
• Min Bar: 35

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools, Work Holding Tools
• Series: RD
• Stroke Inches: 6.25
• Stroke MM: 159
• SubTypes: General Purpose Cylinder

• Designed for long life, the best choice for production applications
• Unique mounting configurations simplify fixturing
• Baked enamel finish for increased corrosion resistance
• Double-acting operation develops force in both directions, providing maximum versatility
• Plunger wiper reduces contamination, extending cylinder life

• Accessories: AD181, AD182, AD183, AD152

EP RD46K2

• Type: Service Kit

• SubTypes: Repair Part

EP RD2510

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000
• Min Bar: 35

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools, Work Holding Tools
• Series: RD
• Stroke Inches: 10.25
• Stroke MM: 260
• SubTypes: General Purpose Cylinder

• Designed for long life, the best choice for production applications
• Unique mounting configurations simplify fixturing
• Baked enamel finish for increased corrosion resistance
• Double-acting operation develops force in both directions, providing maximum versatility
• Plunger wiper reduces contamination, extending cylinder life

• Accessories: AD191, AD192, AD193, AD153

EP RD91

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000
• Min Bar: 35

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools, Work Holding Tools
• Series: RD
• Stroke Inches: 1.13
• Stroke MM: 28
• SubTypes: General Purpose Cylinder

• Designed for long life, the best choice for production applications
• Unique mounting configurations simplify fixturing
• Baked enamel finish for increased corrosion resistance
• Double-acting operation develops force in both directions, providing maximum versatility
• Plunger wiper reduces contamination, extending cylinder life

• Accessories: AD171, AD172, AD173, AD151

EP RD910K2

• Type: Service Kit

• SubTypes: Repair Kit

EP RD93

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000
• Min Bar: 35

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools, Work Holding Tools
• Series: RD
• Stroke Inches: 3.13
• Stroke MM: 79
• SubTypes: General Purpose Cylinder

• Designed for long life, the best choice for production applications
• Unique mounting configurations simplify fixturing
• Baked enamel finish for increased corrosion resistance
• Double-acting operation develops force in both directions, providing maximum versatility
• Plunger wiper reduces contamination, extending cylinder life

• Accessories: AD171, AD172, AD173, AD151

EP RJA1538

• Multiple-tooth pawls for strength & safety.
• Large base ensures a firm foundation.
• Drop-forged, alloy steel, heat-treated components.
• Plated springs to resist corrosion.
• Double-lever sockets for jacking in close quarters.
• Our Jack design specifications meet or exceed ANSI / ASME B30.1 Safety Standards.
• The RJA1538 pole jack is designed for pole pulling applications. Chain and I-Beam are ordered separately.
• Carrying handles make the positioning and transporting of the 10 (44,5), 15 (89) and 20 (133,4) ton (kN) ratchet jacks simple.

• Type: Jack

• Product Line: Mechanical Tools
• Series: RJ
• Stroke Inches: 21.25
• Stroke MM: 539.8
• SubTypes: Ratchet Jacks

• Capacity Imperial Tons: 8
• Capacity KN: 71,2

• Accessories: SLB70

EP RJ86A

• Multiple-tooth pawls for strength & safety.
• Large base ensures a firm foundation.
• Drop-forged, alloy steel, heat-treated components.
• Plated springs to resist corrosion.
• Double-lever sockets for jacking in close quarters.
• Our Jack design specifications meet or exceed ANSI / ASME B30.1 Safety Standards
• Carrying handles make the positioning and transporting of the 10 (44,5), 15 (89) and 20 (133,4) ton (kN) ratchet jacks simple.

• Type: Jack

• Product Line: Mechanical Tools
• Series: RJ
• Stroke Inches: 13
• Stroke MM: 330.2
• SubTypes: Ratchet Jacks

• Capacity Imperial Tons: 5
• Capacity KN: 44,5

• Accessories: SLB36

EP RK848586A02

• Type: ERP

• SubTypes: Component

EP RK848586A01

• Type: ERP

EP RLP19312

This low-profile hexagon cassette is for use with compatible RSL-Series modular drive units. The low-profile design with an optimum nose radius gives you the access needed for hassle-free bolting in tight spaces.

For heavy use and enduring durability, RLP-Series Cassettes are constructed from robust steel and are easily fixed to the RSL Drive Unit using four Allen Key Bolts.

The wide range of interchangeable hexagon cassette sizes provides the versatility to complete a wide range of bolting applications. For exceptionally tight spaces consider the RLP Slimline Stepped Width Cassettes which can also be used with the same drive unit.

Constant torque output provides accuracy of plus/minus 3% across full stroke.

• Type: Torque Wrench

• Product Group: Torque Wrenches, Torque Wrench Pumps
• Product Line: Bolting Tools
• Series: RLP
• SubTypes: Cassette - Imperial or Metric

• Accessories: ERT19024

EP RLL1502

• Load-return - for weighing, lifting and positioning applications.
• Lock nut tested to 150% of rated load.
• Lock nut provides safe mechanical load holding for an extended period of time.
• Red band warns operator to end of stroke, over-flow port prevents over-stroke.
• Built-in tilt saddle to improve side-load resistance.
• Body, lock nut and saddle feature black nitride coating to improve corrosion and wear resistance.
• Low-Profile for use in confined areas.

• Type: Hydraulic Cylinders
• Max PSI: 10150

• Product Line: Hydraulic Tools
• Series: RLL
• Stroke Inches: 1.77
• Stroke MM: 45
• SubTypes: High Tonnage Lock Nut Cylinder

• Capacity Imperial Tons: 158
• Capacity KN: 1429
• Capacity Metric Tons: 143

EP RLT111

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10150

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RLT
• Stroke Inches: 1.57
• Stroke MM: 40
• SubTypes: Low Height Telescopic Cylinder

• Single-Acting, load return
• Nitrocarburization surface treatment for improved load and wear resistance and corrosion protection
• The longer stroke length of telescopic cylinders will save you time and simplify projects by moving a load a greater distance and eliminating the use of temporary cribbing.
• For use in confined spaces: machinery positioning, tool fastening
• Mounting bolt holes for easy fixturing
• Up to 3% side-load of maximum capacity
• Design safety factor complies with ASME B30.1 & EN1494
• CR400 coupler for compatibility with standard product
• High-Alloy steel for maximum strength
• 1st Stage: maximum load capacity at lower stroke.
• 2nd Stage: extended stroke with lower capacity than the 1st stage.
• Final Stage: maximum stroke extension with lowest capacity.

EP RLS302

• Compact low-profile design.
• HD spring for fast retraction.
• Grooved plunger to stabilize the load.
• Stop ring for piston blow-out protection.
• Rod wiper protects inner cylinder from dirt.
• Plated piston to resist scoring & corrosion.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: RLS
• Stroke Inches: 2.44
• Stroke MM: 62
• SubTypes: Low Height Cylinder

• Capacity Imperial Tons: 30
• Capacity KN: 266,9

EP RR1006K

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Repair Kit