GRACO INC. S10595
GRACO INC. S10595 branded products
AGITATOR, DIRECT, DRIVE
GG 25M481
GG 25M481
AGITATOR, DIRECT, DRIVE
Graco 25M481 Stainless Steel Direct Drive, 30/55 gallon, 1 stainless steel 8-inch (20 cm) impeller
Radial piston air motor driven agitators are reliable, simple and cost-effective solutions for low to medium speed (<500 rpm), low to medium viscosity (<1000 cp) agitation applications.
Application: For wood (top coat, primer) and general finishing applications- Recommended agitator rotation: Clockwise
- Sound pressure level at 70 psig (maximum recommended speed): Less than 75 dBA
- Maximum allowable process fluid temperature: 194° F (90° C)
- Air Inlet Size (cm): 0.635
- Air Inlet Size (in): 1/4
- Air Inlet Size (mm): 6.35
- Air Inlet Thread Type: NPT
- Maximum Air Inlet Pressure (bar): 5
- Maximum Air Inlet Pressure (kPa): 500
- Maximum Air Inlet Pressure (psi): 70
- Maximum Speed (RPM): 500
- Maximum Viscosity (cP): 500
- Maximum Working Pressure (bar): 5
- Maximum Working Pressure (kPa): 500
- Maximum Working Pressure (psi): 70
- Motor Type: Pneumatic - Radial Piston
$2,560.00
KIT, UNION, FITTING
GG 25M496
GG 25M496
KIT, UNION, FITTING
Graco 25M496 G-Lock Push-To-Connect Stud Fitting - 90°, 1/4 in, Field-Installable
Application: For use with 1/8 in ID hose only.
- G-Lock Push-To-Connect (PTC) Fitting
- 1/4 in field-installable stud
- 90 degree
- Connection Type: Push-to-Connect
- Hose Inside Diameter (in): 0.125
- Hose Inside Diameter (mm): 3
- Maximum Working Pressure (bar): 207
- Maximum Working Pressure (kPa): 20670
- Maximum Working Pressure (MPa): 20.7
- Maximum Working Pressure (psi): 3000
$20.90
KIT, UNION, FITTING
GG 25M497
GG 25M497
KIT, UNION, FITTING
Graco 25M497 G-Lock Push-To-Connect Stud Fitting - Straight, 1/4 in, Field-Installable
Application: For use with 1/8 in ID hose only.
- G-Lock Push-To-Connect (PTC) Fitting
- Straight 1/4 in field-installable stud
- Connection Type: Push-to-Connect
- Hose Inside Diameter (in): 0.125
- Hose Inside Diameter (mm): 3
- Maximum Working Pressure (bar): 207
- Maximum Working Pressure (kPa): 20670
- Maximum Working Pressure (MPa): 20.7
- Maximum Working Pressure (psi): 3000
$11.00
Kit, REPAIR, AMZ
GG 25M525
GG 25M525
KIT,REPAIR,AMZ
Graco 25M525 AMZ Repair Kit
KIT INCLUDES: MODULE, GCA, MZLP4 W DB [QTY. 1], LABEL, IDENTIFICATION [QTY. 1], SOFTWARE, GCA, MZLP4, APP [QTY. 1], SOFTWARE, GCA, MZLP4 DB, APP [QTY. 1]
$1,805.00
KIT, AIR MOTOR, PISTON, REBUILD
GG 25M535
GG 25M535
KIT, AIR MOTOR, PISTON, REBUILD
Graco 25M535 Radial Piston Air Motor Rebuild Kit
Radial piston air motor driven agitators are reliable, simple and cost-effective solutions for low to medium speed (<500 rpm), low to medium viscosity (<1000 cp) agitation applications.
Application: For wood (top coat, primer) and general finishing applications- Maintain easily – air line lubrication not required.
- Sound pressure level at 70 psig (maximum recommended speed): Less than 75 dBA
- Air Inlet Size (cm): 0.635
- Air Inlet Size (in): 1/4
- Air Inlet Size (mm): 6.35
- Air Inlet Thread Type: NPT
- Maximum Air Inlet Pressure (bar): 5
- Maximum Air Inlet Pressure (kPa): 500
- Maximum Air Inlet Pressure (psi): 70
- Maximum Speed (RPM): 500
- Motor Type: Pneumatic - Radial Piston
$722.00
Kit, Driver, APD20, Vertical
GG 25N519
GG 25N519
KIT,DRIVER,APD20,VERTICAL
KIT INCLUDES: DRIVER, NON-HAZ, APD20, VERTICAL [QTY. 1], LABEL, WARNING [QTY. 1], BOX, JUNCTION, POWER, MOTOR, APD [QTY. 1], SCREW, SHCS M8X60 [QTY. 4 ], PLUG, PIPE HEADLES [QTY. 1], GRIP, CORD, .35-.63, 3/4 [QTY. 1], SWITCH, DISCONNECT, 40A [QTY. 1], COVER, JUCTION BOX, APD MOTOR [QTY. 1], SCREW, SOCKET, FL HD [QTY. 4 ], KNOB, DISCONNECT, PANEL, BLACK [QTY. 1], FERRULE, 16 GA TWIN WIRE [QTY. 2], LABEL, CAUTION [QTY. 1], DOCUMENT, DECLARATION [QTY. 1], LABEL, E-FLO SP [QTY. 1]
$14,140.00
ENDURA-FLO PUMP, 3:1 AODD, 350, NPT, ADV
GG 25M761
GG 25M761
ENDURA-FLO PUMP, 3:1 AODD, 350, NPT, ADV
Endura-Flo 3D350, 3:1 Air Operated Diaphragm Pump, 350cc, NPT, DataTrak The Endura-Flo 3D offers extended durability. The isolated air section of the 3:1 Endura-Flo pump prevents fluids from entering the air section and muffler. Ideal for fluid transfer and supply, small paint circulation and piggable paint systems requiring a lower pressure range and seeking extended diaphragm life. Endure-Flo diaphragms last longer against extreme operating conditions Easy access to critical components for fast online maintenance Pumps offer low pulsation output and smooth changeover for quick color changes, saving you time and money Minimal solvent to flush and consistent startup pressure make it perfect for multiple color change and piggable systems Custom mounting options include rotatable fluid manifolds, mounting brackets and spring loaded check cartridges DataTrek option prevents runaway and tracks material usage
$11,860.00
GL-1 SST INJECTOR, REPLACEMENT
GG 25N109
GG 25N109
GL-1 SST INJECTOR, REPLACEMENT
Graco 25N109 GL-1™ 316 SST Grease Injector - Replacement Injector
Custom fit your system with Graco&prime, s adjustable GL-1 series grease injectors. Designed to meet the needs of each lube point, these systems provide years of reliable operation in the harshest operating environments.
Application: Adjustable volume output the most demanding applications- The GL-1 SST injectors are offered as a a replacement injector for manifold systems for easy customization to a variety of applications
- Includes an adjustable hex head nut to make adjusting the output simple
- No vent holes and fully enclosed press fittings to prevent leaking lubricant
- Rugged, single piece uni-body design built for the harshest environments
- Model: GL-1
- Adjustable: Adjustable
- Application: In-Plant Machinery, Off-Road Equipment, In-Plant Equipment and Machinery, Mining, Wind Energy
- Compatible Material: Grease
- Compatible Metering Device: Single Line Parallel, Single Line
- Cycle Indicator: Visual Pin
- Feedback Options: Visual Pin Indication
- For Use With: Grease dispense in highly corrosive environments
- Material: Stainless Steel
- Maximum NLGI Grade: #2
- Maximum Operating Pressure (psi): 3500
- Maximum Operating Temperature (°C): 190
- Maximum Operating Temperature (°F): 374
- Maximum Output Volume (in³): 0.08
- Maximum Working Pressure (bar): 241
- Maximum Working Pressure (kg/cm²): 246
- Maximum Working Pressure (kPa): 24132
- Maximum Working Pressure (MPa): 24.1
- Maximum Working Pressure (psi): 3500
- Meter Type: Positive Displacement
- Minimum Operating Pressure (psi): 1850
- Minimum Output Volume (in³): 0.008
- Minimum Working Pressure (bar): 128
- Minimum Working Pressure (kg/cm²): 130
- Minimum Working Pressure (kPa): 12755
- Minimum Working Pressure (MPa): 12.8
- Minimum Working Pressure (psi): 1850
- Number of Adjustment Turns: 10
- Outlet Size (in): 1/8 NPT
- Outlet Thread Gender: Female
- Outlet Thread Type: NPT
$488.00
KIT, PUMP, 4B, BELLOWS, 1500 CC
GG 25N408
GG 25N408
KIT, PUMP, 4B, BELLOWS, 1500 CC
Graco 25N408 Sealed 4-Ball Lower, 1500cc, Chrome Cylinders, Standard Top Plate Rotation
Graco’s Sealed 4-Ball Lower needs no routine maintenance and prevents unexpected downtime. The sealed fluid section eliminates the need for TSL (throat seal liquid). Designed to keep pumping in the event of a bellows failure, the lower allows you to schedule maintenance.
- Chrome coating on lower rods and cylinders works well for fine pigment paint and fluids with low lubrication, such as solvents and water.
- Connection kits contain tie rods and adapters – everything required to upgrade most legacy Graco circulation pumps to the latest technology. Refer to manual 311876 for complete information.
- Fluid Inlet Size (cm): 3.81
- Fluid Inlet Size (in): 1.5
- Fluid Inlet Thread Gender: Male
- Fluid Inlet Thread Type: Tri-Clamp
- Fluid Outlet Size (in): 1.5
- Fluid Outlet Thread Gender: Male
- Fluid Outlet Thread Type: Tri-Clamp
- Maximum Flow Rate (GPM): 7.9
- Maximum Operating Temperature (°F): 150
- Maximum Output (cm³): 30000
- Maximum Pump Speed (CPM): 20
- Maximum Working Pressure (psi): 460
$10,840.00
ENDURA-FLO PUMP, 3:1 AODD, 350, NPT, STD
GG 25M758
GG 25M758
ENDURA-FLO PUMP, 3:1 AODD, 350, NPT, STD
Endura-Flo 3D350, 3:1 Air Operated Diaphragm Pump, 350cc, NPT The Endura-Flo 3D offers extended durability. The isolated air section of the 3:1 Endura-Flo pump prevents fluids from entering the air section and muffler. Ideal for fluid transfer and supply, small paint circulation and piggable paint systems requiring a lower pressure range and seeking extended diaphragm life. Endure-Flo diaphragms last longer against extreme operating conditions Easy access to critical components for fast online maintenance Pumps offer low pulsation output and smooth changeover for quick color changes, saving you time and money Minimal solvent to flush and consistent startup pressure make it perfect for multiple color change and piggable systems Custom mounting options include rotatable fluid manifolds, mounting brackets and spring loaded check cartridges
$10,770.00
ENDURA-FLO PUMP, 3:1 AODD, 350, BSP, STD
GG 25M759
GG 25M759
ENDURA-FLO PUMP, 3:1 AODD, 350, BSP, STD
Endura-Flo 3D350, 3:1 Air Operated Diaphragm Pump, 350cc, BSPP The Endura-Flo 3D offers extended durability. The isolated air section of the 3:1 Endura-Flo pump prevents fluids from entering the air section and muffler. Ideal for fluid transfer and supply, small paint circulation and piggable paint systems requiring a lower pressure range and seeking extended diaphragm life. Endure-Flo diaphragms last longer against extreme operating conditions Easy access to critical components for fast online maintenance Pumps offer low pulsation output and smooth changeover for quick color changes, saving you time and money Minimal solvent to flush and consistent startup pressure make it perfect for multiple color change and piggable systems Custom mounting options include rotatable fluid manifolds, mounting brackets and spring loaded check cartridges
$10,630.00
ENDURA-FLO PUMP, 3:1 AODD, 350, TRI, ADV
GG 25M760
GG 25M760
ENDURA-FLO PUMP, 3:1 AODD, 350, TRI, ADV
Graco 25M760 Endura-Flo 3D350, 3:1 Air Operated Diaphragm Pump, 350cc, Tri-Clamp, DataTrak
The Endura-Flo 3D offers extended durability. The isolated air section of the 3:1 Endura-Flo pump prevents fluids from entering the air section and muffler. Ideal for fluid transfer and supply, small paint circulation and piggable paint systems requiring a lower pressure range and seeking extended diaphragm life.
- Endure-Flo diaphragms last longer against extreme operating conditions
- Easy access to critical components for fast online maintenance
- Pumps offer low pulsation output and smooth changeover for quick color changes, saving you time and money
- Custom mounting options include rotatable fluid manifolds, mounting brackets and spring loaded check cartridges
- DataTrek option prevents runaway and tracks material usage
- Model: Endura-Flo
- Series: 3D350
- Air Inlet Size (in): 1/2
- Air Inlet Thread Gender: Female
- Air Inlet Thread Type: NPT
- Application: Circulation
- Compatible Material: High Solids, Xirallic, CARC, Metallics, Stains, Varnish, Fast-Set
- Connection Type: Tri-Clamp
- Fluid Inlet Size (cm): 2.54
- Fluid Inlet Size (in): 1
- Fluid Inlet Size (mm): 25.4
- Fluid Outlet Size (cm): 2.54
- Fluid Outlet Size (in): 1
- Fluid Outlet Size (mm): 25.4
- Includes: Tri-Clamp Fittings, DataTrak
- Material: Stainless Steel
- Maximum Air Pressure (bar): 7
- Maximum Air Pressure (kPa): 700
- Maximum Air Pressure (MPa): 0.7
- Maximum Air Pressure (psi): 100
- Maximum Cycle Rate (CPM): 20
- Maximum Flow Rate (GPM): 5.5
- Maximum Flow Rate (L/min): 20.8
- Maximum Fluid Pressure (bar): 21
- Maximum Fluid Pressure (kPa): 2100
- Maximum Fluid Pressure (MPa): 2.1
- Maximum Fluid Pressure (psi): 300
- Maximum Fluid Pressure (bar): 21
- Maximum Fluid Pressure (kPa): 2100
- Maximum Fluid Pressure (MPa): 2.1
- Maximum Fluid Pressure (psi): 300
- Maximum Operating Temperature (°C): 50
- Maximum Operating Temperature (°F): 122
- Power Source: Air
- Pump Ratio: 3:1
$12,910.00
ENDURA-FLO PUMP, 3:1 AODD, 150, TRI, STD
GG 25M739
GG 25M739
ENDURA-FLO PUMP, 3:1 AODD, 150, TRI, STD
Endura-Flo 3D150, 3:1 Air Operated Diaphragm Pump, 150cc, Tri-Clamp The Endura-Flo 3D offers extended durability. The isolated air section of the 3:1 Endura-Flo pump prevents fluids from entering the air section and muffler. Ideal for fluid transfer and supply, small paint circulation and piggable paint systems requiring a lower pressure range and seeking extended diaphragm life. Endure-Flo diaphragms last longer against extreme operating conditions Easy access to critical components for fast online maintenance Pumps offer low pulsation output and smooth changeover for quick color changes, saving you time and money Minimal solvent to flush and consistent startup pressure make it perfect for multiple color change and piggable systems Custom mounting options include rotatable fluid manifolds, mounting brackets and spring loaded check cartridges
$6,730.00
ENDURA-FLO PUMP, 3:1 AODD, 150, NPT, ADV
GG 25M743
GG 25M743
ENDURA-FLO PUMP, 3:1 AODD, 150, NPT, ADV
Endura-Flo 3D150, 3:1 Air Operated Diaphragm Pump, 150cc, NPT, DataTrak The Endura-Flo 3D offers extended durability. The isolated air section of the 3:1 Endura-Flo pump prevents fluids from entering the air section and muffler. Ideal for fluid transfer and supply, small paint circulation and piggable paint systems requiring a lower pressure range and seeking extended diaphragm life. Endure-Flo diaphragms last longer against extreme operating conditions Easy access to critical components for fast online maintenance Pumps offer low pulsation output and smooth changeover for quick color changes, saving you time and money Minimal solvent to flush and consistent startup pressure make it perfect for multiple color change and piggable systems Custom mounting options include rotatable fluid manifolds, mounting brackets and spring loaded check cartridges DataTrek option prevents runaway and tracks material usage
$7,820.00
CLEANER, HIGH PRESSURE, 4040 HG-DD
GG 25N677
GG 25N677
CLEANER, HIGH PRESSURE, 4040 HG-DD
G-Force II 4040 HG-DD Pressure Washer Ideal for large residential or commercial contractors, the G-Force II 4040 HG-DD pressure washer delivers higher power and flow and is built tough to handle weekly use and deliver high flow and pressure in a compact, durable package. Honda® Engines- Reliable, powerful & easy-to-start
- Oil Alert shuts down engine to prevent damage if oil level drops too low
- Thermal sensor prevents pump from overheating in bypass mode
- Up to 40% lighter than steel frames
- Corrosion resistant to water and chemicals
- Standard on all Graco models
- Lifetime Warranty
- Standard Graco feature
- Allows water bypass pump to eliminate pressure build-up in the system
- No need to pull the gun trigger while starting the washer
- Compact design with fewer components and lighter weight
- Pump is connected directly to the drive shaft of the engine
- Pump rpm matches that of the engine (usually around 3500 rpm)
$2,880.00
ENDURA-FLO PUMP, 3:1 AODD, 150, BSP, STD
GG 25M741
GG 25M741
ENDURA-FLO PUMP, 3:1 AODD, 150, BSP, STD
Endura-Flo 3D150, 3:1 Air Operated Diaphragm Pump, 150cc, BSPP The Endura-Flo 3D offers extended durability. The isolated air section of the 3:1 Endura-Flo pump prevents fluids from entering the air section and muffler. Ideal for fluid transfer and supply, small paint circulation and piggable paint systems requiring a lower pressure range and seeking extended diaphragm life. Endure-Flo diaphragms last longer against extreme operating conditions Easy access to critical components for fast online maintenance Pumps offer low pulsation output and smooth changeover for quick color changes, saving you time and money Minimal solvent to flush and consistent startup pressure make it perfect for multiple color change and piggable systems Custom mounting options include rotatable fluid manifolds, mounting brackets and spring loaded check cartridges
$7,190.00
ENDURA-FLO PUMP, 3:1 AODD, 150, NPT, STD
GG 25M740
GG 25M740
ENDURA-FLO PUMP, 3:1 AODD, 150, NPT, STD
Graco 25M740 Endura-Flo 3D150, 3:1 Air Operated Diaphragm Pump, 150cc, NPT
The Endura-Flo 3D offers extended durability. The isolated air section of the 3:1 Endura-Flo pump prevents fluids from entering the air section and muffler. Ideal for fluid transfer and supply, small paint circulation and piggable paint systems requiring a lower pressure range and seeking extended diaphragm life.
- Endure-Flo diaphragms last longer against extreme operating conditions
- Easy access to critical components for fast online maintenance
- Pumps offer low pulsation output and smooth changeover for quick color changes, saving you time and money
- Custom mounting options include rotatable fluid manifolds, mounting brackets and spring loaded check cartridges
- Model: Endura-Flo
- Series: 3D150
- Air Inlet Size (in): 1/4
- Air Inlet Thread Gender: Female
- Air Inlet Thread Type: NPT
- Application: Circulation
- Compatible Material: High Solids, Xirallic, CARC, Metallics, Stains, Varnish, Fast-Set
- Connection Type: Threaded
- Fluid Inlet Size (cm): 1.27
- Fluid Inlet Size (in): 1/2
- Fluid Inlet Size (mm): 12.7
- Fluid Inlet Thread Type: NPT
- Fluid Outlet Size (cm): 1.27
- Fluid Outlet Size (in): 1/2
- Fluid Outlet Size (mm): 12.7
- Fluid Outlet Thread Type: NPT
- Includes: NPT Fittings
- Material: Stainless Steel
- Maximum Air Pressure (bar): 7
- Maximum Air Pressure (kPa): 700
- Maximum Air Pressure (MPa): 0.7
- Maximum Air Pressure (psi): 100
- Maximum Cycle Rate (CPM): 20
- Maximum Flow Rate (GPM): 2.4
- Maximum Flow Rate (L/min): 9.1
- Maximum Fluid Pressure (bar): 21
- Maximum Fluid Pressure (kPa): 2100
- Maximum Fluid Pressure (MPa): 2.1
- Maximum Fluid Pressure (psi): 300
- Maximum Fluid Pressure (bar): 21
- Maximum Fluid Pressure (kPa): 2100
- Maximum Fluid Pressure (MPa): 2.1
- Maximum Fluid Pressure (psi): 300
- Maximum Operating Temperature (°C): 50
- Maximum Operating Temperature (°F): 122
- Minimum Operating Temperature (°C): 0
- Minimum Operating Temperature (°F): 32
- Overall Height (in): 12.23
- Power Source: Air
- Pump Ratio: 3:1
$6,730.00
AGITATOR, IN-DRUM, 1.5 BUNG,
GG 25N881
GG 25N881
AGITATOR, IN-DRUM, 1.5 BUNG,
In-Drum, 1.5-inch (3.8 cm) Bung Mount Radial piston air motor driven agitators are reliable, simple and cost-effective solutions for low to medium speed (<500 rpm), low to medium viscosity (<1000 cp) agitation applications. For wood (top coat, primer) and general finishing applications Recommended agitator rotation: Clockwise Sound pressure level at 70 psig (maximum recommended speed): Less than 75 dBA Maximum allowable process fluid temperature: 194° F (90° C) Bung adapter sizes: 1 1/2–11.5 npsm and 2–11.5 npsm
$2,400.00
AGITATOR, IN-DRUM, 2.0 BUNG,
GG 25N882
GG 25N882
AGITATOR, IN-DRUM, 2.0 BUNG,
In-Drum, 2-inch (5 cm) Bung Mount Radial piston air motor driven agitators are reliable, simple and cost-effective solutions for low to medium speed (<500 rpm), low to medium viscosity (<1000 cp) agitation applications. For wood (top coat, primer) and general finishing applications Recommended agitator rotation: Clockwise Sound pressure level at 70 psig (maximum recommended speed): Less than 75 dBA Maximum allowable process fluid temperature: 194° F (90° C) Bung adapter sizes: 1 1/2–11.5 npsm and 2–11.5 npsm
$2,610.00
Kit, Sanitary Gasket-K1 Ep-4
GG 25P064
GG 25P064
KIT, SANITARY GASKET-K1 EP-4
Graco 25P064 EPDM Seal Kit for 3-inch Flapper Pump
$130.00
GT 750 PUMP, TOPPER
GG 25P544
GG 25P544
GT 750 PUMP, TOPPER
Graco 25P544 GT 750 36:1 Grease Transfer Topper-Inductor Package for 400 lb (180 kg) drums
The GT 750 36:1 pump was engineered for efficient grease transfer in demanding applications. The Topper-Inductor package allows for quick drum changes and reduces strain on operators.
Call for pricing
KIT, DIAPHRAGM-H1 EO
GG 25P270
GG 25P270
KIT, DIAPHRAGM-H1 EO
EPDM Overmold Diaphragm Kit for 2- to 4-inch Pump
$1,610.00
FUSION PC GUN, RND, 01
GG 25P588
GG 25P588
FUSION PC GUN, RND, 01
Fusion ProConnect Gun with Round 01 Mix Chamber and 0.042 in (1.06 mm) Orifice Size A perfect rebuild in seconds is now possible with the revolutionary Fusion PC (ProConnect) gun, featuring an all-in-one cartridge head that replaces multiple individual parts of the fluid section with a single component. Simply replacing the cartridge completely eliminates the need for a time-consuming traditional rebuild, keeping you spraying and minimizing costly downtime. Unlike any other spray foam gun available A single cartridge replaces the entire fluid section in seconds Built on top of the time-tested Fusion Air Purge platform, the PC gun sprays exactly like a Fusion AP Integrated check valves for cross-over containment 13 parts are replaced by a single ProConnect cartridge Eliminates the need to purchase fluid section o-rings Spare ProConnect cartridges can replace your back-up guns Retrofit Kit available to convert existing Fusion AP guns
$3,870.00
KIT, DIAPHRAGM-F1 PO
GG 25P208
GG 25P208
KIT, DIAPHRAGM-F1 PO
PTFE/EPDM Overmold Diaphragm Kit for 1.5-inch Pump
$1,485.00
FUSION PC GUN, RND, 02
GG 25P589
GG 25P589
FUSION PC GUN, RND, 02
Graco 25P589 Fusion ProConnect Gun with Round 02 Mix Chamber and 0.052 in (1.3 mm) Orifice Size
A perfect rebuild in seconds is now possible with the revolutionary Fusion PC (ProConnect) gun, featuring an all-in-one cartridge head that replaces multiple individual parts of the fluid section with a single component. Simply replacing the cartridge completely eliminates the need for a time-consuming traditional rebuild, keeping you spraying and minimizing costly downtime.
Application: Unlike any other spray foam gun available- A single cartridge replaces the entire fluid section in seconds
- Built on top of the time-tested Fusion Air Purge platform, the PC gun sprays exactly like a Fusion AP
- Integrated check valves for cross-over containment
- Eliminates the need to purchase fluid section o-rings
- Spare ProConnect cartridges can replace your back-up guns
- Retrofit Kit available to convert existing Fusion AP guns
- Model: Fusion PC
- Series: Round
- Air Inlet Size (cm): 0.635
- Air Inlet Size (in): 1/4
- Air Inlet Size (mm): 6.35
- Air Inlet Thread Type: NPT
- Applicator Type: Manual
- Compatible Material: Adhesives, Polyurethane, Polyurea, Polyurethane Coating, Spray Polyurethane Foam
- Component A Inlet Size (cm): 1.27
- Component A Inlet Size (in): 1/2-20
- Component A Inlet Size (mm): 12.7
- Component A Inlet Thread Type: UNF
- Component B Inlet Size (cm): 1.42875
- Component B Inlet Size (in): 9/16-18
- Component B Inlet Size (mm): 14.2875
- Component B Inlet Thread Type: UNF
- Component Type: Plural-Component
- Fluid Orifice Size (cm): 0.107
- Fluid Orifice Size (in): .052
- Fluid Orifice Size (mm): 1.07
- For Use With: Non-Flammable Foam and Polyurea
- Gun Activation: Manual
- Gun Included: 1
- Gun Type: Air Purge Gun
- Gun Weight (g): 1338
- Gun Weight (kg): 1.3
- Gun Weight (lb): 2.95
- Gun Weight (oz): 47
- Impingement Port Size (in): 0.052
- Impingement Port Size (mm): 1.32
- Includes: PC52RD Mix Chamber Tip
- Maximum Air Inlet Pressure (bar): 9
- Maximum Air Inlet Pressure (kPa): 900
- Maximum Air Inlet Pressure (MPa): 0.9
- Maximum Air Inlet Pressure (psi): 130
- Maximum Air Pressure (bar): 9
- Maximum Air Pressure (kPa): 900
- Maximum Air Pressure (MPa): 0.9
- Maximum Air Pressure (psi): 130
- Maximum Flow Rate @ PSI (lb/min): 50
- Maximum Fluid Pressure (bar): 241
- Maximum Fluid Pressure (kPa): 24100
- Maximum Fluid Pressure (MPa): 24.1
- Maximum Fluid Pressure (psi): 3500
- Maximum Fluid Temperature (°C): 93
- Maximum Fluid Temperature (°F): 200
- Maximum Fluid Pressure (bar): 241
- Maximum Fluid Pressure (kPa): 24100
- Maximum Fluid Pressure (MPa): 24.1
- Maximum Fluid Pressure (psi): 3500
- Maximum Fluid Temperature (°C): 93
- Maximum Fluid Temperature (°F): 200
- Maximum Fluid Working Pressure (bar): 245
- Maximum Fluid Working Pressure (MPa): 24.5 <
$3,870.00
KIT, FUSION PC, RETRO, BARE
GG 25P704
GG 25P704
KIT, FUSION PC, RETRO, BARE
Fusion ProConnect Retrofit Kit without Mix Chamber Transform your Fusion Air Purge gun into a Fusion PC with the ProConnect Retrofit Kit, allowing you to take full advantage of what the Fusion PC delivers: A perfect rebuild in seconds. The Retrofit Kit is compatible with all Fusion AP guns and can be combined with any Fusion PC mix chamber (sold separately). Acquire all the advantages of the revolutionary Fusion ProConnect while utilizing your existing Fusion AP handle and fluid manifold. Same Fusion AP gun, all new possibilities A single cartridge replaces the entire fluid section in seconds Sprays exactly like a Fusion AP Integrated check valves for cross-over containment 13 parts are replaced by a single ProConnect cartridge Eliminates the need to purchase fluid section o-rings Spare ProConnect cartridges can replace your back-up guns
$1,275.00
KIT, AIR MOTOR BEARING, REBUILD
GG 25P720
GG 25P720
KIT, AIR MOTOR BEARING, REBUILD
Radial Piston Air Motor Bearing Rebuild Kit
$183.50
REGULATOR, BP, AIRPILOT, LOW-FLOW
GG 25R487
GG 25R487
REGULATOR, BP, AIRPILOT, LOW-FLOW
Graco 25R487 Low Shear Fluid Back Pressure Regulator, 300 Max psi, 10 gpm Max flow rate, SST, Pneumatic, high wear, sanitary inlet/outlet
Graco’s low shear back pressure regulator (BPR) minimizes shear and prevents paint degradation so that manufacturers produce consistent finish quality.
- Air operated model works with Intelligent Paint Kitchen (IPK) control to reduce energy consumption and paint shear
- Ultralife series ceramic coated parts resist wear and increase service life
- Low profile, compact design and backwards compatibility mean easy installation and replacement
- Compatible Material: Waterborne, Solvent borne
- Gauge Port Size (cm): 0.635
- Gauge Port Size (in): 1/4
- Gauge Port Size (mm): 6.35
- Gauge Port Type: NPT
- Inlet Size (cm): 3.8
- Inlet Size (in): 1.5
- Inlet Size (mm): 38
- Inlet Thread Type: Sanitary Flange
- Maximum Air Inlet Pressure (bar): 7
- Maximum Air Inlet Pressure (kg/cm²): 7
- Maximum Air Inlet Pressure (kPa): 690
- Maximum Air Inlet Pressure (psi): 100
- Maximum Flow Rate (GPM): 10
- Maximum Flow Rate (L/min): 38
- Maximum Operating Temperature (°C): 50
- Maximum Operating Temperature (°F): 122
- Maximum Regulated Pressure (bar): 17.6
- Maximum Regulated Pressure (kg/cm²): 17.6
- Maximum Regulated Pressure (kPa): 1724
- Maximum Regulated Pressure (psi): 250
- Maximum Viscosity (cP): 1000
- Maximum Working Pressure (bar): 21.1
- Maximum Working Pressure (kg/cm²): 21.1
- Maximum Working Pressure (kPa): 2068
- Maximum Working Pressure (psi): 300
- Minimum Operating Temperature (°C): 0
- Minimum Operating Temperature (°F): 32
- Minimum Regulated Pressure (bar): 1.8
- Minimum Regulated Pressure (kg/cm²): 1.8
- Minimum Regulated Pressure (kPa): 172
- Minimum Regulated Pressure (MPa): 0.17
- Minimum Regulated Pressure (psi): 25
- Outlet Size (cm): 3.8
- Outlet Size (in): 1.5
- Outlet Size (mm): 38
- Outlet Thread Type: Sanitary Flange
$2,270.00
REGULATOR, BP, MECHANICAL, LOW-FLOW
GG 25R488
GG 25R488
REGULATOR, BP, MECHANICAL, LOW-FLOW
Graco 25R488 Low Shear Fluid Back Pressure Regulator, 300 Max psi, 10 gpm Max flow rate, SST, Mechanical, high wear, sanitary inlet/outlet
Graco’s low shear back pressure regulator (BPR) minimizes shear and prevents paint degradation so that manufacturers produce consistent finish quality.
- Innovative flow path geometry provides industry-leading low shear capability
- Ultralife series ceramic coated seat and flow directors significantly increase wear resistance capability and service life
- Best-in-class performance holds pressure constant while flow rate changes
- Compatible Material: Waterborne, Solvent borne
- Gauge Port Size (cm): 0.635
- Gauge Port Size (in): 1/4
- Gauge Port Size (mm): 6.35
- Gauge Port Type: NPT
- Inlet Size (cm): 3.8
- Inlet Size (in): 1.5
- Inlet Size (mm): 38
- Inlet Thread Type: Sanitary Flange
- Maximum Flow Rate (GPM): 10
- Maximum Flow Rate (L/min): 38
- Maximum Operating Temperature (°C): 50
- Maximum Operating Temperature (°F): 122
- Maximum Regulated Pressure (bar): 17.6
- Maximum Regulated Pressure (kg/cm²): 17.6
- Maximum Regulated Pressure (kPa): 1724
- Maximum Regulated Pressure (psi): 250
- Maximum Viscosity (cP): 1000
- Maximum Working Pressure (bar): 21.1
- Maximum Working Pressure (kg/cm²): 21.1
- Maximum Working Pressure (kPa): 2068
- Maximum Working Pressure (psi): 300
- Minimum Operating Temperature (°C): 0
- Minimum Operating Temperature (°F): 32
- Minimum Regulated Pressure (bar): 1.8
- Minimum Regulated Pressure (kg/cm²): 1.8
- Minimum Regulated Pressure (kPa): 172
- Minimum Regulated Pressure (MPa): 0.17
- Minimum Regulated Pressure (psi): 25
- Outlet Size (cm): 3.8
- Outlet Size (in): 1.5
- Outlet Size (mm): 38
- Outlet Thread Type: Sanitary Flange
$1,225.00
REGULATOR, BACK PRES, MP, AIR, 30 TO 1
GG 25R490
GG 25R490
REGULATOR, BACK PRES, MP, AIR, 30 TO 1
Graco 25R490 Medium Pressure Fluid Back Pressure Regulator, 3000 Max psi, 5 gpm Max flow rate, SST, Pneumatic
Improve finishing process control with this medium pressure, pneumatic back pressure regulator (BPR).
- Interface with Graco’s Intelligent Paint Kitchen (IPK), controlling pressure and flow without human intervention.
- Gain better resolution than other BPR brands, adjusting more accurately to keep fluid pressure at desired levels.
- Compatible Material: Waterborne, Solvent borne
- Gauge Port Size (cm): 0.635
- Gauge Port Size (in): 1/4
- Gauge Port Size (mm): 6.35
- Gauge Port Type: NPT
- Inlet Size (cm): 0.95
- Inlet Size (in): 0.375
- Inlet Size (mm): 9.5
- Inlet Thread Type: NPT
- Maximum Air Inlet Pressure (bar): 7
- Maximum Air Inlet Pressure (kg/cm²): 7
- Maximum Air Inlet Pressure (kPa): 690
- Maximum Air Inlet Pressure (psi): 100
- Maximum Flow Rate (GPM): 5
- Maximum Flow Rate (L/min): 19
- Maximum Operating Temperature (°C): 50
- Maximum Operating Temperature (°F): 122
- Maximum Regulated Pressure (bar): 207
- Maximum Regulated Pressure (kg/cm²): 207
- Maximum Regulated Pressure (kPa): 20700
- Maximum Regulated Pressure (psi): 3000
- Maximum Viscosity (cP): 250
- Maximum Working Pressure (bar): 211
- Maximum Working Pressure (kg/cm²): 211
- Maximum Working Pressure (kPa): 20680
- Maximum Working Pressure (psi): 3000
- Minimum Operating Temperature (°C): 0
- Minimum Operating Temperature (°F): 32
- Minimum Regulated Pressure (bar): 17
- Minimum Regulated Pressure (kg/cm²): 17
- Minimum Regulated Pressure (kPa): 1720
- Minimum Regulated Pressure (psi): 250
- Outlet Size (cm): 0.95
- Outlet Size (in): 0.375
- Outlet Size (mm): 9.5
- Outlet Thread Type: NPT
$3,940.00
5 Gallon (20L) Heated Platen with EPDM Wiper
GG 25R535
GG 25R535
5 Gallon (20L) Heated Platen with EPDM Wiper
$3,410.00
REGULATOR, BACK PRESS, MP, MECHANICAL
GG 25R491
GG 25R491
REGULATOR, BACK PRESS, MP, MECHANICAL
Graco 25R491 Medium Pressure Fluid Back Pressure Regulator, 3000 Max psi, 5 gpm Max flow rate, SST, Mechanical with locking nut
Improve fluid control without having to add a compressed air line with this spring-operated back pressure regulator (BPR).
- Easy installation is another benefit of the mechanical medium pressure BPR.
- Compatible Material: Waterborne, Solvent borne
- Gauge Port Size (cm): 0.635
- Gauge Port Size (in): 1/4
- Gauge Port Size (mm): 6.35
- Gauge Port Type: NPT
- Inlet Size (cm): 0.95
- Inlet Size (in): 0.375
- Inlet Size (mm): 9.5
- Inlet Thread Type: NPT
- Maximum Air Inlet Pressure (bar): 7
- Maximum Air Inlet Pressure (kg/cm²): 7
- Maximum Air Inlet Pressure (kPa): 690
- Maximum Air Inlet Pressure (psi): 100
- Maximum Flow Rate (GPM): 5
- Maximum Flow Rate (L/min): 19
- Maximum Operating Temperature (°C): 50
- Maximum Operating Temperature (°F): 122
- Maximum Regulated Pressure (bar): 207
- Maximum Regulated Pressure (kg/cm²): 207
- Maximum Regulated Pressure (kPa): 20700
- Maximum Regulated Pressure (psi): 3000
- Maximum Viscosity (cP): 250
- Maximum Working Pressure (bar): 211
- Maximum Working Pressure (kg/cm²): 211
- Maximum Working Pressure (kPa): 20680
- Maximum Working Pressure (psi): 3000
- Minimum Operating Temperature (°C): 0
- Minimum Operating Temperature (°F): 32
- Minimum Regulated Pressure (bar): 17
- Minimum Regulated Pressure (kg/cm²): 17
- Minimum Regulated Pressure (kPa): 1720
- Minimum Regulated Pressure (psi): 250
- Outlet Size (cm): 0.95
- Outlet Size (in): 0.375
- Outlet Size (mm): 9.5
- Outlet Thread Type: NPT
$2,010.00
G-MINI PUMP, 24V, 1L, CONTROLLER
GG 25R801
GG 25R801
G-MINI PUMP, 24V, 1L, CONTROLLER
Graco 25R801 G-Mini® Grease Lubrication Pump with Controller, 24 VDC, 1 Liter
Make the most of your space, budget and machines. The new full-featured G-Mini offers reliable lubrication in a small footprint to fit more types of machines. Use it to simplify everyday maintenance, extend lifecycles and optimize uptime. It’s rugged and tough, perfect for handling the daily, 24/7 rigors of any job, both big and small. Best of all, it comes with a modest price tag – boosting your productivity and profitability.
- Follower Plate and Stir Paddle - This unique combination combats oil separation while ensuring the pump element &Prime, loading chamber&Prime, is always full.
- M12 Input - M12 cycle or proximity switch input standard on all pumps with a controller.
- 5-Wire CPC Power Cable - Multifunction cable supplies power to the pump, pairs with a remote manual run button, and provides low level or cycle fault output.
- One Pump Element - 0.18 in3/min (3 cm3/min), 4,100 psi (280 bar)
- Easy-to-program controller can be utilized for both time based and cycle based systems and provides low level alert and alarm.
- Rugged Construction - Designed to withstand the harshest of environments, IP69K rated.
- Model: G-Mini
- Application: Off-Road Equipment, On-Road Vehicles, Industrial, Wind Energy
- Approvals: CE, EAC
- Compatible Material: Grease
- Compatible Metering Device: Series Progressive
- Control Options: Internal Controller
- Fluid Inlet Type: Zerk Fitting to Fill Reservoir
- Fluid Outlet Size (in): 1/4
- Fluid Outlet Thread Gender: Female
- Fluid Outlet Thread Type: NPSF
- IP Rating: IP69K
- Maximum Flow Rate (ci/min): 3
- Maximum NLGI Grade: #2
- Maximum Operating Temperature (°C): 70
- Maximum Operating Temperature (°F): 158
- Maximum Voltage (V dc): 32
- Maximum Working Pressure (bar): 280
- Maximum Working Pressure (psi): 4061
- Minimum Operating Temperature (°C): -15
- Minimum Operating Temperature (°F): 5
- Minimum Voltage (V dc): 18
- Number of Pump Elements: Up to 2
- Number of Sensor Inputs: 1
- Overall Depth (in): 6.57
- Overall Height (in): 12.2
- Overall Width (in): 6.97
- Power Connection Type: CPC
$1,085.00
IQ Valve Outlet Manifold, 200MM Nozzle
GG 25R639
GG 25R639
IQ Valve Outlet Manifold, 200MM Nozzle
$802.00
IQ VALVE OUTLET MANIFOLD 60MM NOZZLE
GG 25R632
GG 25R632
IQ VALVE OUTLET MANIFOLD 60MM NOZZLE
$419.00
G-MINI PUMP, 24V, 1L, NC
GG 25R800
GG 25R800
G-MINI PUMP, 24V, 1L, NC
Graco 25R800 G-Mini® Grease Lubrication Pump, 24 VDC, 1 Liter
Make the most of your space, budget and machines. The new full-featured G-Mini offers reliable lubrication in a small footprint to fit more types of machines. Use it to simplify everyday maintenance, extend lifecycles and optimize uptime. It’s rugged and tough, perfect for handling the daily, 24/7 rigors of any job, both big and small. Best of all, it comes with a modest price tag – boosting your productivity and profitability.
- Follower Plate and Stir Paddle - This unique combination combats oil separation while ensuring the pump element &Prime, loading chamber&Prime, is always full.
- 5-Wire CPC Power Cable - Multifunction cable supplies power to the pump, pairs with a remote manual run button, and provides low level or cycle fault output.
- 1 liter reservoir option
- No Controller: pair with either an external controller or PLC.
- Rugged Construction - Designed to withstand the harshest of environments, IP69K rated.
- Model: G-Mini
- Application: Off-Road Equipment, On-Road Vehicles, Industrial, Wind Energy
- Approvals: CE, EAC
- Compatible Material: Grease
- Compatible Metering Device: Series Progressive
- Control Options: External Controller
- Fluid Inlet Type: Zerk Fitting to Fill Reservoir
- Fluid Outlet Size (in): 1/4
- Fluid Outlet Thread Gender: Female
- Fluid Outlet Thread Type: NPSF
- For Use With: Series Progressive
- IP Rating: IP69K
- Maximum Flow Rate (ci/min): 3
- Maximum NLGI Grade: #2
- Maximum Operating Temperature (°C): 70
- Maximum Operating Temperature (°F): 158
- Maximum Voltage (V dc): 32
- Maximum Working Pressure (bar): 280
- Maximum Working Pressure (psi): 4061
- Minimum Operating Temperature (°C): -15
- Minimum Operating Temperature (°F): 5
- Minimum Voltage (V dc): 18
- Number of Pump Elements: Up to 2
- Overall Depth (in): 6.57
- Overall Height (in): 12.2
- Overall Width (in): 6.97
- Power Connection Type: CPC
$930.00
VALVE, DMV
GG 25T670
GG 25T670
VALVE, DMV
Voltex Two-Component Dynamic Mix Valve The Voltex Dynamic Mix Valve is a rotary static valve that consistently mixes and dispenses materials requiring exceptional mixing energy. Engineered with rugged components and precision controls that eliminate dispensing inconsistencies, reduce maintenance downtime, and optimize material usage. Reliably mixes and dispenses difficult foaming polyurethanes, low viscosity silicones, and other hard to blend two component chemistries. Easily integrates with Graco meter, mix, and dispense systems like the PR70 for a complete dispensing solution. Control system delivers precision RPM control, and real time monitoring for dispensing process stability. Built with durable check valves and disposable mixers that reduce maintenance and downtime.
$12,620.00
MONITOR, TLM, ULTRASONIC, CEL
GG 25T461
GG 25T461
MONITOR, TLM, ULTRASONIC, CEL
Graco 25T461 Pulse® Level Ultrasonic Cellular Tank Monitor
You deliver more than fluids. You’re delivering insight. Graco Pulse Level offers highly intuitive tank-level-visibility options to help you optimize deliveries, margins and customer service. Track tank levels, capture and apply data, and assign distribution routes quickly, accurately and confidently from the industry’s leading fluid management expert. Pulse Level is compatible with 4G LTE networks, so you don’t have to worry about investing in soon-to-be-obsolete technology.
- Cellular Communication - No need for local network connection.
- Long Battery Life - 5 year battery life with replaceable C batteries
- Ultrasonic Sensor - Measure tanks 13 ft tall.
- Model: Pulse
- Approvals: FCC, CE
- Battery Chemistry: Alkaline
- Battery Life (h): 5 years
- Battery Size: C
- Cylindrical Tank Maximum Height (ft): 13
- Cylindrical Tank Maximum Height (m): 4
- Cylindrical Tank Maximum Volume (gal): 999999
- Cylindrical Tank Maximum Volume (L): 999999
- Fluid Level Measurement Accuracy (%): +/-1 in. (+/- 2 cm)
- For Use With: Pulse Level
- Maximum Ambient Temperature (°F): 140
- Maximum Operating Temperature (°C): 50
- Maximum Operating Temperature (°F): 122
- Maximum RF Operating Temperature (°F): 122
- Maximum Storage Temperature (°C): 60
- Maximum Storage Temperature (°F): 140
- Minimum Ambient Temperature (°F): -22
- Minimum RF Operating Temperature (°F): 0
- Minimum Storage Temperature (°C): -30
- Minimum Storage Temperature (°F): -22
- Number of Batteries: 4
- Obround Tank Maximum Height (ft): 13
- Obround Tank Maximum Height (m): 4
- Obround Tank Maximum Length (ft): Any
- Obround Tank Maximum Length (m): Any
- Obround Tank Maximum Volume (gal): 999999
- Obround Tank Maximum Volume (L): 999999
- Overall Height (cm): 15
- Overall Height (ft): 0.49
- Overall Height (in): 5.9
- Overall Height (m): 0.015
- Overall Height (mm): 150
- Overall Length (cm): 9.3
- Overall Length (ft): 0.305
- Overall Length (in): 3.66
- Overall Length (m): 0.093
- Overall Length (mm): 93
- Overall Width (cm): 10.1
- Overall Width (ft): 0.333
- Overall Width (in): 4
- Overall Width (m): 0.0101
- Overall Width (mm): 101
- Product Type: Tank Level Monitor (TLM)
$950.00
REGULATOR, BACK PRESS, MP, 20:1
GG 25T477
GG 25T477
REGULATOR, BACK PRESS, MP, 20:1
Graco 25T477 Medium Pressure Fluid Back Pressure Regulator, 2000 Max psi, 5 gpm Max flow rate, SST, Pneumatic
Improve finishing process control with this medium pressure, pneumatic back pressure regulator (BPR).
- Gain better resolution than other BPR brands, adjusting more accurately to keep fluid pressure at desired levels.
- Interface with Graco’s Intelligent Paint Kitchen (IPK), controlling pressure and flow without human intervention.
- Compatible Material: Waterborne, Solvent borne
- Gauge Port Size (cm): 0.635
- Gauge Port Size (in): 1/4
- Gauge Port Size (mm): 6.35
- Gauge Port Type: NPT
- Inlet Size (cm): 0.95
- Inlet Size (in): 0.375
- Inlet Size (mm): 9.5
- Inlet Thread Type: NPT
- Maximum Air Inlet Pressure (bar): 7
- Maximum Air Inlet Pressure (kg/cm²): 7
- Maximum Air Inlet Pressure (kPa): 690
- Maximum Air Inlet Pressure (psi): 100
- Maximum Flow Rate (GPM): 5
- Maximum Flow Rate (L/min): 19
- Maximum Operating Temperature (°C): 50
- Maximum Operating Temperature (°F): 122
- Maximum Regulated Pressure (bar): 138
- Maximum Regulated Pressure (kg/cm²): 138
- Maximum Regulated Pressure (kPa): 13800
- Maximum Regulated Pressure (psi): 2000
- Maximum Viscosity (cP): 250
- Maximum Working Pressure (bar): 211
- Maximum Working Pressure (kg/cm²): 211
- Maximum Working Pressure (kPa): 20680
- Maximum Working Pressure (psi): 3000
- Minimum Operating Temperature (°C): 0
- Minimum Operating Temperature (°F): 32
- Minimum Regulated Pressure (bar): 17
- Minimum Regulated Pressure (kg/cm²): 17
- Minimum Regulated Pressure (kPa): 1720
- Minimum Regulated Pressure (psi): 250
- Outlet Size (cm): 0.95
- Outlet Size (in): 0.375
- Outlet Size (mm): 9.5
- Outlet Thread Type: NPT
$3,970.00
REGULATOR, BP, MECHANICAL, HIGH-FLOW
GG 25R647
GG 25R647
REGULATOR, BP, MECHANICAL, HIGH-FLOW
Low Shear Fluid Back Pressure Regulator, 300 Max psi, 25 gpm Max flow rate, SST, Mechanical, high wear, sanitary inlet/outlet Graco’s low shear back pressure regulator (BPR) minimizes shear and prevents paint degradation so that manufacturers produce consistent finish quality. Innovative flow path geometry provides industry-leading low shear capability Ultralife series ceramic coated seat and flow directors significantly increase wear resistance capability and service life Best-in-class performance holds pressure constant while flow rate changes
$2,780.00
VOLTEX CONTROL, WALL MOUNT, DMV, ADM
GG 25T673
GG 25T673
VOLTEX CONTROL, WALL MOUNT, DMV, ADM
Voltex Wall Mount Control Box for PR70 with ADM Use Voltex wall mounted control box to complete your dynamic mixing system. Easily integrates with the PR70 or HFR for a total dispensing solution. Control box equipped with the ADM easily integrates with the PR70 or HFR. Stable, strong wall mount base with a small footprint for work space optimization. Contains all electronic components necessary for running the precision servo motor of the Voltex dynamic mix valve.
$7,140.00
ProBell Hose, Bundled, Non-ES, 11 M
GG 25T743
GG 25T743
ProBell Hose, Bundled, Non-ES, 11 M
$5,700.00
IQ Valve Nozzle Extension Rod Bearing
GG 25R634
GG 25R634
IQ Valve Nozzle Extension Rod Bearing
$105.50