Hydraullic Units

EP CATS300

Tilt Saddle for 250 and 300 Ton HCG, HCL and HCR Series Cylinders
The use of a tilt saddle can extend the life of an Enerpac cylinder. Hydraulic cylinders are built to ensure efficient and safe use time after time, but even the toughest cylinders can be damaged by an excessive side load. Side loading can occur even when the load is vertically placed on top of the cylinder, when cylinders are extended too far - (especially long stroke cylinders), or when the saddle on the end of the plunger fails to make sufficient contact with the load. Greater contact can be achieved using Enerpac Tilt Saddles.

• Type: Cylinder Accessories

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: CATS
• SubTypes: Tilt Saddle

• With safety and convenience in mind the new tilt saddles are designed to allow bolting to the cylinder - which means they can be used safely in any orientation without the risk of the saddle dropping off.
• CATS-Tilt Saddles use a nitrocarburization surface treatment for improved corrosion protection, helping to maintain a professional look through their usage life.

EP CATS52

Tilt Saddle for 25-30 Ton RC Series Cylinders, and 30 Ton RR Series Cylinders
The use of a tilt saddle can extend the life of an Enerpac cylinder. Hydraulic cylinders are built to ensure efficient and safe use time after time, but even the toughest cylinders can be damaged by an excessive side load. Side loading can occur even when the load is vertically placed on top of the cylinder, when cylinders are extended too far - (especially long stroke cylinders), or when the saddle on the end of the plunger fails to make sufficient contact with the load. Greater contact can be achieved using Enerpac Tilt Saddles.

• Type: Cylinder Accessories

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: CATS
• SubTypes: Tilt Saddle

• With safety and convenience in mind the new tilt saddles are designed to allow bolting to the cylinder - which means they can be used safely in any orientation without the risk of the saddle dropping off.
• CATS-Tilt Saddles use a nitrocarburization surface treatment for improved corrosion protection, helping to maintain a professional look through their usage life.

EP CB891045

SADDLE
Single-Acting Hollow Plunger Cylinders (RCH-Series and equivalent)

• Type: Service Kit

• SubTypes: Saddle Kit

EP CB894045

SADDLE 20 TON
Single-Acting Hollow Plunger Cylinders (RCH-Series and equivalent)

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Saddle

EP CBA519028-1E

SCREW-BHCS, HEX, M5X0.8 X 16, 10.9, PLAIN
Single-Acting Low-Height Flat-Jac Cylinders (RSM-Series and equivalent)

• Type: Service Kit

• SubTypes: Screw, Hex

EP CBA619028-1B

SCREW-FHS, HEX, M6X1 X 16, 10.9, PLAIN
Single-Acting Cylinders (RAC-Series and equivalent)

• Type: Service Kit

• SubTypes: Screw, Hex

EP CDB70252

15200 lbs Capacity, .98 in Stroke, Double-Acting, Block Hydraulic Cylinder
Applications: Clamp, Push, Pull

• Type: Hydraulic Cylinders
• Max Bar: 350
• Max PSI: 5000
• Min Bar: 40

• Product Group: Cylinders and Jacks
• Product Line: Work Holding Tools
• Series: CDB
• Stroke Inches: 0.98
• Stroke MM: 27.4
• SubTypes: Workholding Block Cylinder

• Six clamping capacities enable you to choose the right size for your application
• Variety of strokes, to meet design needs
• Double acting and Single acting (spring return), allows selection of cylinder that best conforms to your hydraulic system
• Oil connection alternatives: cylinders incorporate both manifold mount and plumbed options to meet your fixturing needs
• Compact cylinder design does not require large amounts of space on your fixture
• Integral wiper ring, keeps contaminants out of cylinder to extend life
• Internal threaded plunger
• Manifold O-ring ports
• Black oxide base
• Hard chrome-plated plunger
• BSPP oil port
• Strong return spring
• Filtered vent plug

• Accessories: BS202

EP CDB-70502

BLOCK CYLINDER D/A, 70 kN

EP CDB70K1

SEAL KIT,D/A BLOCK CYL 70KN
Block Cylinder Imperial

• Type: Service Kit

EP CH945900W

VALVE ASSM

• Type: ERP

• SubTypes: Repair Part

EP CJ338018

FILTER PIPE
PAM-Series Twin Air

• Type: Service Kit

• SubTypes: Filter Pipe

EP CJ999028

SET SCREW
H-Frame Presses (IP-Series)

• Type: Service Kit

• SubTypes: Screw

EP CK354950SR

AIR PISTON ASM.REPL.KIT
PA-Series

• Type: Service Kit

• SubTypes: Piston Kit

EP CN721026

FILL DECAL
Single-Acting Cylinders (RC-Series and equivalent)

• Type: Service Kit

• SubTypes: Decal

EP CN742550

HEX
H-Frame Presses (IP-Series)

• Type: Service Kit

• SubTypes: Repair Part

EP CN750111

CYLINDER BRACKET
Roll Frame Presses (IPR-Series)

• Type: Service Kit

• SubTypes: Bracket

EP CR136149

TIE ROD
H-Frame Presses (IP-Series)

• Type: Service Kit

• SubTypes: Tie Rod

EP CR215

3/8" NPTF, High Flow Coupler Dust Cap

• Type: Coupler

• Product Line: Hydraulic Tools
• Series: C - Simplex
• SubTypes: Coupler Dust Cap

EP CST18251

3950 lbs Capacity, 0.98 in Stroke, Single-Acting, Threaded Body, Hydraulic Cylinder
Applications: Push

• Type: Hydraulic Cylinders
• Max PSI: 5000

• Product Group: Cylinders and Jacks
• Product Line: Work Holding Tools
• Series: CST
• Stroke Inches: 0.98
• SubTypes: Workholding Threaded Cylinder

• Minimum cylinder diameter combined with maximized clamping forces
• Threaded body allows fine positioning and easy installation
• Internal plunger wipers allow maintenance-free, high-cycle performance
• Center-tapped plungers will hold workpiece contact buttons
• Single-acting models with spring return simplify hydraulic tubing requirements
• Double-acting models are recommended for high-cycle applications

• Accessories: MF331, FN331, BS81, Y3121

EP CST-40381

8800 LB. THRD. CYL, 1.5 STROKE, IMPER

EP CU587028

SCREW, CAP, METRIC SOCKET HD
Single-Acting Low-Height Flat-Jac Cylinders (RSM-Series and equivalent)

• Type: Service Kit

• SubTypes: Screw

EP CUSP200

235.0 ton Capacity, 0.59 in Stroke, High Tonnage Ultra Flat Hydraulic Cylinder

CUSP-Series Low Height Hydraulic Cylinders, also known as hydraulic pancake cylinders, combine an impressive power to height ratio with a tilting saddle function to distribute the load evenly and prevent side load.

These are available in several high-tonnage capacities, making them the right choice for confined spaces where other cylinders will not fit.

There are several configurations to choose from, including high tonnage capacities up to 1000 tons (10165 kN). These ultra-flat hydraulic cylinders have collapsed heights from 1.4 up to 4.06†(35.5 to 103 mm).

All are finished with a tough Nitrocarburized coating for enhanced corrosion protection in harsh working environments.

Applications: Lift

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10150

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: CUSP
• Stroke Inches: 0.59
• Stroke MM: 14.9
• SubTypes: Low Height Cylinder

• Up to 4% side load of maximum capacity
• Extremely low collapsed height
• Integrated tilting function up to 4 degrees to evenly distribute the load
• Nitrocarburized surface treatment for harsh conditions
• " Red Line" for visual maximum stroke limitation Up to 4% side load of maximum capacity
• Coupler included

• Spare Part(s): CUSP200K

EP DA11433900SR

Hand Pump Assembly

EP DA2286028

SCREW
Single-Acting Cylinders (RC-Series and equivalent)

• Type: Service Kit

• SubTypes: Screw

EP DA3568980

RELAY -GLOBAL PUMP
ZE/ZW-Series

• Type: Service Kit

• SubTypes: Repair Part