GRACO INC. S10595

GG 94/0880-C/98

GG 94/1020/98

GG 94/1007/98

GG 947084

GG 946761

GG 947085

GG 947089

GG 947091

GG 947937

GG 948208

GG 949634

KIT, REBUILD 2K2

KIT INCLUDES: BEARING, SLEEVE 1/4, 3/8, 1/4NYL [QTY. 2], PACKING, O-RING [QTY. 2], PIN, DOWEL 1/8 X 1.25 18-8 SST [QTY. 1], NUT, LOCK [QTY. 2], PACKING, O-RING, BUNA-N [QTY. 2], PACKING, O-RING [QTY. 2], PACKING, U-CUP URT 1/4, 1/2, 1/8 UR [QTY. 2], BEARING, LUBE 2K2 [QTY. 2], SEAL, U-CUP POLYMT 1/4, 1/2, 1/4 [QTY. 2], NEEDLE, 2K2 SST HARDENED [QTY. 2], GASKET, AIR MANIFOLD [QTY. 1], LUBRICANT, SYNTHETIC, GREASE, 3 OZ [QTY. 1], PACKING, O-RING [QTY. 2], INSERT, SUFF-BACK, 2K2 [QTY. 2], RESTRICTOR, 2K2 3/64 I.D. [QTY. 3], RESTRICTOR, 2K2 1/8 I.D. [QTY. 3], PIN, DOWEL 3/32 X 3/8 18-8 SST [QTY. 4 ], PACKING, O-RING [QTY. 3], PACKING, O-RING [QTY. 2], GASKET, SEAT [QTY. 2], SEAT, VALVE [QTY. 2]

GG 949796

GG 94G039

G1 STANDARD PUMP, G-24NC-2L0A00-LD000000

Graco 94G039 G1 Standard Grease Lubrication Pump, 24 VDC, 2 Liter, DIN, Wiper, Low Level

Simple solution. Sophisticated results. Choose the user friendly Graco G1 Pump when you need a reliable, simple alternative to manual lubrication. Work smarter and get better productivity from your equipment with G1 Series lubrication pumps.

• G1 Standard has no internal controller for a low cost solution.
• 2 liter reservoir
• Connect to 24 VDC
• Hard Working Pump - G1 comes with one pump element installed that reliably delivers lubricant when you need it.
• Achieve Uninterrupted Material Flow - With its advanced flow dynamics the contoured base flows lubricants directly to the pump inlet, significantly reducing stagnant areas where grease can separate.
• Experience Our Long Life Design - Engineered offset drive design minimizes load and stress on the motor and pump element.

• Model: G1
• Series: Standard

• Application: On-Road Vehicles, Off-Road Equipment

• Compatible Material: Grease
• Compatible Metering Device: Series Progressive, Single Line Parallel

• Control Options: Standard

• Fluid Outlet Size (in): 0.25
• Fluid Outlet Size (mm): 6.3500
• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: NPSF

• Includes: Wiper Arm, External Low Level

• IP Rating: IP69K

• Maximum Flow Rate (ci/min): 0.25

• Maximum NLGI Grade: #2

• Maximum Run Time (min): 30

• Maximum Voltage (V dc): 32

• Maximum Working Pressure (bar): 351.6
• Maximum Working Pressure (kPa): 35160
• Maximum Working Pressure (MPa): 35.1
• Maximum Working Pressure (psi): 5100

• Minimum Voltage (V dc): 18

• Number of Pump Elements: 1

• Overall Depth (cm): 22.9
• Overall Depth (in): 9
• Overall Depth (mm): 229

• Overall Height (cm): 33.7
• Overall Height (in): 13.25
• Overall Height (mm): 337
• Overall Width (cm): 20.3
• Overall Width (in): 8
• Overall Width (mm): 203

• Power Connection Type: DIN

• Power Type: Electric

GG 95/0005/02

GG 95/0110/00

GG 17P754

GG 17P879

GG 17R220

GG 17P485

GG 17R291

GG 17P502

KIT, GASKET, FFLP, SOLVENT

Graco 17P502 RAC X FF LP Solvent OneSeal, 5 pack

Designed specifically for the RAC X FF LP SwitchTips, these single seal gaskets help keep the tip in place when using solvent-based materials.

• Model: RAC X
• Series: Tip Gasket

• Compatible Tip Type: RAC X

GG 17P486

GG 17P712

KIT, VACUVALVE

Graco 17P712 VacuValve Cap Replacements, 3 pack

The VacuValve keeps air from entering the FlexLiner System.

• Model: Graco

• Includes: Cap Hinge Valve (3)

• Number of Pieces: 3

GG 17R827

GG 17P726

KIT,HEAD,PROBLER2,SST

KIT INCLUDES: HEAD, PROBLER2, SST [QTY. 1], KIT INCLUDES: INSERT, CHAMBER, MIX, .059 [QTY. 1],

GG 17P717

GG 17P501

KIT, GASKET, FFLP

Graco 17P501 RAC X FF LP OneSeal, 5 pack

Designed specifically for the RAC X FF LP SwitchTips, these single seal gaskets help keep the tip in place.

• Model: RAC X
• Series: Tip Gasket

• Compatible Tip Type: RAC X

GG 17P653

EDGE II GUN, HVLP, CUP, PKGD

Graco 17P653 EDGE II Gun with Metal Cup

Maximize your spraying performance with the innovative HVLP EDGE II Gun. Cutting edge technology such as intuitive gun controls, Quick Release fluid set, and optimized air pressure and airflow will help you achieve the highest quality finish available in fine finish spraying.

• Integrated Flow Control

  Combines material and air flow into one simple control

  Optimized to spray the majority of fine finish applications

  Quick adjustment with 360 degree rotation and indicator for repeatable spray setting

• Adjustable Air Cap

  3-position rotation to change spray pattern

  Conveniently located at the front of the gun

• Exclusive Quick Clean Check Valve

  Allows more air pressure into the material cup to spray heavier material

  Easily clean and reuse versus replace

  Located by gun to reduce clogged valves due to paint contamination

• Quick Release Needle Design

  Change out needles from the front of the gun with just a click

  Easy to change, easy to clean with no tools needed

  Remove front air cap and nozzle

  Slide trigger lever to release needle

  Pull needle out

• Model: HVLP
• Series: EDGE II

• Compatible Material: Varnish, Enamel, Latex, Stains

• For Use With: FinishPro HVLP Sprayers

• Gun Activation: Manual
• Gun Type: HVLP Gun
• Gun Weight (oz): 20

• Includes: 1 qt (0.95 L) Metal Cup, #3 Quick Release Fluid Set

• Maximum Air Inlet Pressure (bar): 0.7
• Maximum Air Inlet Pressure (kPa): 70
• Maximum Air Inlet Pressure (MPa): 0.07
• Maximum Air Inlet Pressure (psi): 13
• Maximum Air Pressure (bar): 0.7

• Maximum Air Pressure (kPa): 70
• Maximum Air Pressure (MPa): 0.07
• Maximum Air Pressure (psi): 10

• Maximum Fluid Pressure (bar): 3.5
• Maximum Fluid Pressure (kPa): 350
• Maximum Fluid Pressure (MPa): 0.35
• Maximum Fluid Pressure (psi): 50

• Maximum Fluid Pressure (bar): 3.5
• Maximum Fluid Pressure (kPa): 350
• Maximum Fluid Pressure (MPa): 0.35
• Maximum Fluid Pressure (psi): 50

GG 17R301

GG 17R290

GG 17R299

GG 17R462

GG 17P550

KIT, FLEXLINER COMPLETE, 32OZ

Graco 17P550 FlexLiner System 32 oz

Adding an additional FlexLiner System for your handheld will make refilling even easier and faster. Includes 32 ounce cup holder, 32 ounce FlexLiner Paint Bag, lid and plug.

• Model: FlexLiner

• Maximum Volume Capacity (mL): 1000
• Maximum Volume Capacity (oz): 32

GG 562834

MXP VALVE, SINGLE 150S W/IND

Graco 562834 Trabon MXP Modular Divider Valve with Indicator - MXP-150S - 0.300 in cu (4.92 cm cu )

The Trabon MXP Series offers the largest output available in a series progressive system. Can be easily accessorized with magnetic and electronic proximity switch cycle indicators to provide positive assurance of a successful lube event.

• Quick change valve sections can be removed from the base assembly without disturbing any lube lines - minimizing labor cost and maximizing your machine uptime
• Alternate outlet on face of valves can be fitted with optional performance indicators, taking the guesswork out of troubleshooting
• Robust design is virtually indestructible and built to perform in extreme environments

• Model: Trabon
• Series: MXP

• Application: Off-Road Equipment, In-Plant Machinery

• Compatible Material: Oil, Grease

• Cycle Indicator: Cycle Indicator

• Discharge Per Piston Stroke (in cu ): 0.300

• Divider Valve Series: MXP

• Material: Carbon Steel

• Maximum Cycle Rate (cycles/min): 60

• Maximum NLGI Grade: #2

• Maximum Operating Temperature ( degree C): 176
• Maximum Operating Temperature ( degree F): 350

• Maximum Working Pressure (bar): 207
• Maximum Working Pressure (kPa): 20700
• Maximum Working Pressure (psi): 3000

• Minimum Working Pressure (psi): 200

• Number of Outlets: 1

GG 562872

TIMER, SOLID STATE

Graco 562872 LubriSystem Solid State Timer - 115 VAC

• Solid State Timer, 115 VAC
• Lubriquip part number 163-400-000

• Model: LubriSystem

• Application: In-Plant Machinery

• Frequency (Hz): 50/60

• Maximum Amperage (A): 3

• Maximum On Time (min): 13
• Maximum Operating Temperature ( degree C): 55
• Maximum Operating Temperature ( degree F): 131

• Maximum Storage Temperature ( degree C): 85
• Maximum Storage Temperature ( degree F): 185

• Minimum On Time (min): 0.2
• Minimum Operating Temperature ( degree C): -18
• Minimum Operating Temperature ( degree F): 0

• Minimum Storage Temperature ( degree C): -55
• Minimum Storage Temperature ( degree F): -67

• Number of Cycle Intervals: 8

• Overall Height (cm): 8.001
• Overall Height (in): 3.15
• Overall Height (mm): 80.01
• Overall Length (cm): 10
• Overall Length (in): 4.06
• Overall Length (mm): 103
• Overall Width (cm): 6.35
• Overall Width (in): 2.5
• Overall Width (mm): 63.5

• Power Source: AC

GG 562884

RESERVOIR, 12LB PLSTC GRS GPS

Graco 562884 12 lb. (5.42 kg) Plastic Cylindrical Grease Reservoir

• 12 lb (5.42 kg) Plastic Cylindrical Reservoir
• Lubriquip part number 185-100-000

• Model: Trabon

• Application: In-Plant Machinery

• Compatible Material: Grease

• Material: Plastic

GG 562888

GG 562891

GG 562897

RESERVOIR, PLSTC GRS LUBEMASTER 20L

Graco 562897 20 lb. Plastic Grease Reservoir

• 20 lb (9.06 kg) Reservoir
• Lubriquip part number 185-100-550

• Compatible Material: Grease

• Material: Plastic

GG 562903

TUBE, RESV REPLACE 20LB PLSTC

Graco 562903 Modu-Flo and E-Pump Spare Parts and Accessories - 20 pt./lb. Plastic Replacement Reservoir Assembly, 6 in OD x 20 in long

• Reservoir Repair Kits - Plastic tube with u-cup seal for part numbers 562893 and 562897
• Lubriquip part number 185-100-740

• Compatible Material: Oil, Grease

• Includes: Reservoir

• Material: Plastic

GG 562920

MODEL 25 LUBRICATOR

Graco 562920 Manzel Model 25 Lubricator

Manzel Model 25 Force Feed Lubricators are economical, general purpose units of double plunger design for precise metering of lubricants (either mineral oil base or synthetics). All working parts are totally enclosed - away from dust, water and impurities - and self-lubricated at all times by the lubricant in the reservoir.

• General-Purpose Lubrication: automatic, precision metering for all types of machinery.
• Pressures: Up to 1000 psi (69 bar)
• Type Pumping Unit: Clear-Vue. Sight Feed Chamber functions at atmospheric pressure. Shows amount of lubricant being pumped.
• Unitized Construction: Contains complete feed regulating mechanism. Equipped with inlet strainer.
• Displacement, Output: 1/4 to 12 drops per stroke with 5/16 in plunger, 1/6 to 6 drops per stroke with 3/16 in plunger.
• Reservoirs: Single Compartment, sheet metal construction.
• Feed Regulator: External screw-type precisely adjustable while idle or in operation.
• Lubriquip part number 225-001-970

• Model: Manzel
• Series: Model 25

• Compatible Material: Oil

GG 563093

FILTER, CANISTER 10

Graco 563093 Replacement Element for Spin-On Oil Filters - 10 Micron

• 10 micron Replacement Filter Element for assemblies 563092, 563095, 564343
• Lubriquip part number 473-000-262

• For Use With: Meter-Flo Pump Packages, Spin-On Oil Filters

GG 562714

MSP VALVE, ASSY MSP 20S

Graco 562714 Trabon MSP Modular Divider Valve - MSP-20S - 0.040 in cu (0.66 cm cu )

The Trabon MSP Series sets the industry standard for quality, reliability, and ease of use features. It was the original modular-style series progressive divider valve and is still the best!

• Quick change valve sections can be removed from the base assembly without disturbing any lube lines - minimizing labor cost and maximizing your machine uptime
• Accessories such as magnetic and electronic proximity switch cycle indicators provide positive assurance of a successful lube event.
• Alternate outlet on face of valves can be fitted with optional performance indicators, taking the guesswork out of troubleshooting
• Lubriquip part number 106-100-045

• Model: Trabon
• Series: MSP

• Application: On-Road Vehicles, Off-Road Equipment, In-Plant Machinery

• Compatible Material: Oil, Grease

• Cycle Indicator: None

• Discharge Per Piston Stroke (in cu ): 0.040

• Divider Valve Series: MSP

• Material: Carbon Steel

• Maximum Cycle Rate (cycles/min): 200

• Maximum NLGI Grade: #2

• Maximum Operating Temperature ( degree C): 176
• Maximum Operating Temperature ( degree F): 350

• Maximum Working Pressure (bar): 241
• Maximum Working Pressure (kPa): 24100
• Maximum Working Pressure (psi): 3500

• Minimum Working Pressure (bar): 14

• Minimum Working Pressure (psi): 200

• Number of Outlets: 1

GG 563074

FILTER, INLET RESTRICTOR, NPTF

Graco 563074 MSP Standard Zero Leak Inlet 90 micron Oil Filter/Restrictor, NPT

• MSP Standard Zero Leak Inlet 90 micron Oil Filter/Restrictor, NPT
• Lubriquip part number 463-410-204

GG 563095

FILTER, 10 MICRON

Graco 563095 Spin-On Oil Filter Assembly with External 150 psi Relief Valve - 200 psi, 3/4 in. NPT, 10 Micron

• 10 micron Spin-On Filter Assembly, NPT, External 150 psi (10.3 bar) Relief
• Lubriquip part number 473-000-271

• Maximum Working Pressure (bar): 14
• Maximum Working Pressure (kPa): 1400
• Maximum Working Pressure (MPa): 140
• Maximum Working Pressure (psi): 200

• Port Size (cm): 1.905
• Port Size (in): 3/4
• Port Size (mm): 19.05

GG 563156

VALVE, RELIEF, 1/4 NPT, 750 PSI

Graco 563156 Automatic Relief Indicator for MX Divider Valves, 750 psi (52 bar)

Keep your machine running while lubrication gets to critical points. These performance indicators pinpoint lube line blockages but allow the lube system to continue to supply lubrication to points that are not blocked.

• No time or effort required for reset after blockage is cleared
• Easy information on blocked lines, high system pressure or blocked bearings
• Works with MSP, MX, MXP, MJ and MHH divider valves

• Model: Trabon

• Application: In-Plant Machinery, Off-Road Equipment, Compressor Equipment

• Compatible Material: Oil, Grease

• Connection Size (in): 0.25

• Indicator Type: Automatic Relief Indicators

• Maximum Working Pressure (bar): 51
• Maximum Working Pressure (kPa): 5100
• Maximum Working Pressure (MPa): 5
• Maximum Working Pressure (psi): 750

• Overall Length (cm): 3
• Overall Length (in): 1.37
• Overall Length (mm): 35

GG 562712

MSP VALVE, ASSY MSP 10S

Graco 562712 Trabon MSP Modular Divider Valve - MSP-10S - 0.020 in cu (0.33 cm cu )

The Trabon MSP Series sets the industry standard for quality, reliability, and ease of use features. It was the original modular-style series progressive divider valve and is still the best!

• Quick change valve sections can be removed from the base assembly without disturbing any lube lines - minimizing labor cost and maximizing your machine uptime
• Accessories such as magnetic and electronic proximity switch cycle indicators provide positive assurance of a successful lube event.
• Alternate outlet on face of valves can be fitted with optional performance indicators, taking the guesswork out of troubleshooting
• Lubriquip part number 106-100-025

• Model: Trabon
• Series: MSP

• Application: On-Road Vehicles, Off-Road Equipment, In-Plant Machinery

• Compatible Material: Oil, Grease

• Cycle Indicator: None

• Discharge Per Piston Stroke (in cu ): 0.020

• Divider Valve Series: MSP

• Material: Carbon Steel

• Maximum Cycle Rate (cycles/min): 200

• Maximum NLGI Grade: #2

• Maximum Operating Temperature ( degree C): 176
• Maximum Operating Temperature ( degree F): 350

• Maximum Working Pressure (bar): 241
• Maximum Working Pressure (kPa): 24100
• Maximum Working Pressure (psi): 3500

• Minimum Working Pressure (bar): 14

• Minimum Working Pressure (psi): 200

• Number of Outlets: 1

GG 563148

SWIVEL, 90 1/8 PORT NITRILE

Graco 563148 Compact 90 degree Angle Swivel - 1/8 inch, Nitrile

The Trabon Straight and Angle Swivels are available in standard ball bearing or compact types. Primarily designed for medium to high pressure service in centralized oil and grease systems, these swivels provide a simple and inexpensive means of making line connections between either stationary, or oscillating surfaces.

• 90 degree Swivel Adapter - 1/8 inch (3.2 mm) NPT x 1/8 inch (3.2 mm) NPT Female
• Lubriquip part number 501-257-000
• Trabon part number 1257

• Angle ( degree ): 90
• Application: On-Road Vehicles

• Compatible Material: Oil, Grease

• Connection Type: Threaded

• For Use With: Pipe

• Material: Steel

• Maximum Working Pressure (bar): 34
• Maximum Working Pressure (kPa): 3400
• Maximum Working Pressure (MPa): 3.4
• Maximum Working Pressure (psi): 500

GG 563161

VALVE, RELIEF, 1/4 NPT, 3000 PSI

Graco 563161 Automatic Relief Indicator for MX Divider Valves, 3000 psi (207 bar)

Keep your machine running while lubrication gets to critical points. These performance indicators pinpoint lube line blockages but allow the lube system to continue to supply lubrication to points that are not blocked.

• No time or effort required for reset after blockage is cleared
• Easy information on blocked lines, high system pressure or blocked bearings
• Works with MSP, MX, MXP, MJ and MHH divider valves

• Model: Trabon

• Application: In-Plant Machinery, Off-Road Equipment, Compressor Equipment

• Compatible Material: Oil, Grease

• Connection Size (in): 0.25

• Indicator Type: Automatic Relief Indicators

• Maximum Working Pressure (bar): 207
• Maximum Working Pressure (kPa): 20700
• Maximum Working Pressure (MPa): 21
• Maximum Working Pressure (psi): 3000

• Overall Length (cm): 3
• Overall Length (in): 1.37
• Overall Length (mm): 35

GG 563160

VALVE, RELIEF, 1/4 NPT, 2500 PSI

Graco 563160 Automatic Relief Indicator for MX Divider Valves, 2500 psi (172 bar)

Keep your machine running while lubrication gets to critical points. These performance indicators pinpoint lube line blockages but allow the lube system to continue to supply lubrication to points that are not blocked.

• No time or effort required for reset after blockage is cleared
• Easy information on blocked lines, high system pressure or blocked bearings
• Works with MSP, MX, MXP, MJ and MHH divider valves

• Model: Trabon

• Application: In-Plant Machinery, Off-Road Equipment, Compressor Equipment

• Compatible Material: Oil, Grease

• Connection Size (in): 0.25

• Indicator Type: Automatic Relief Indicators

• Maximum Working Pressure (bar): 172
• Maximum Working Pressure (kPa): 17200
• Maximum Working Pressure (MPa): 17
• Maximum Working Pressure (psi): 2500

• Overall Length (cm): 3
• Overall Length (in): 1.37
• Overall Length (mm): 35

GG 16D289

GG 16C996

GG 16D329

KIT,SOLVENT METER

Graco 16D329 Solvent Meter (S3000) for ProControl 1KS

GG 16D268

GG 16D658

KIT,CHECK VALVE,2KS

Graco 16D658 Check Valve for ProMix 2KS, 3KS and 2KE Proportioners

• Chop Gun Type: With Cutter

• Compatible Material: Polyester Resin, Gel-Coat

GG 16E993

METER, HELICAL FLOW

GG 16D939

GG 16E376

GG 16F164

GG 16E277

GG 16D932

GG 16E904

GG 16E895

GG 16E227

GG 123816

GG 123882

GG 123909

GG 123910

GG 123970

GG 123968

GG 124048

GG 123934

GG 123971

GG 123988

GG 124058

GG 124061

GG 124149

GG 124164

GG 124313

GG 124306

GG 124344

GG LTX425

RAC X LTX TIP, SPRAY, (425)

Graco LTX425 RAC X SwitchTip, 425

The Reverse-A-Clean (RAC) 425 RAC X SwitchTip produces an 8 to 10 inch fan and has a 0.025 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 20
• Maximum Fan Width (in): 8
• Maximum Fan Width (mm): 254

• Maximum Flow Rate (GPM): 0.67
• Maximum Flow Rate (L/min): 2.54

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 8
• Minimum Fan Width (mm): 203

• Orifice Diameter (in): 0.025

• Pattern Size (in): 8 to 10
• Pattern Size (mm): 203.2 to 254

GG LTX423

RAC X LTX TIP, SPRAY, 423

Graco LTX423 RAC X SwitchTip, 423

The Reverse-A-Clean (RAC) 423 RAC X SwitchTip produces an 8 to 10 inch fan and has a 0.023 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 20
• Maximum Fan Width (in): 8
• Maximum Fan Width (mm): 254

• Maximum Flow Rate (GPM): 0.57
• Maximum Flow Rate (L/min): 2.16

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 8
• Minimum Fan Width (mm): 203

• Orifice Diameter (in): 0.023

• Pattern Size (in): 8 to 10
• Pattern Size (mm): 203.2 to 254

GG LTX427

RAC X LTX TIP, SPRAY, (427)

Graco LTX427 RAC X SwitchTip, 427

The Reverse-A-Clean (RAC) 427 RAC X SwitchTip produces an 8 to 10 inch fan and has a 0.027 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 20
• Maximum Fan Width (in): 8
• Maximum Fan Width (mm): 254

• Maximum Flow Rate (GPM): 0.77
• Maximum Flow Rate (L/min): 2.91

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 8
• Minimum Fan Width (mm): 203

• Orifice Diameter (in): 0.027

• Pattern Size (in): 8 to 10
• Pattern Size (mm): 203.2 to 254

GG LTX421

RAC X LTX TIP, SPRAY, 421

Graco LTX421 RAC X SwitchTip, 421

The Reverse-A-Clean (RAC) 421 RAC X SwitchTip produces an 8 to 10 inch fan and has a 0.021 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 20
• Maximum Fan Width (in): 8
• Maximum Fan Width (mm): 254

• Maximum Flow Rate (GPM): 0.47
• Maximum Flow Rate (L/min): 1.78

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 8
• Minimum Fan Width (mm): 203

• Orifice Diameter (in): 0.021

• Pattern Size (in): 8 to 10
• Pattern Size (mm): 203.2 to 254

GG LTX431

RAC X LTX TIP, SPRAY, (431)

Graco LTX431 RAC X SwitchTip, 431

The Reverse-A-Clean (RAC) 431 RAC X SwitchTip produces an 8 to 10 inch fan and has a 0.031 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 20
• Maximum Fan Width (in): 8
• Maximum Fan Width (mm): 254

• Maximum Flow Rate (GPM): 1.03
• Maximum Flow Rate (L/min): 3.90

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 8
• Minimum Fan Width (mm): 203

• Orifice Diameter (in): 0.031

• Pattern Size (in): 8 to 10
• Pattern Size (mm): 203.2 to 254

GG LTX419

RAC X LTX TIP, SPRAY, 419

Graco LTX419 RAC X SwitchTip, 419

The Reverse-A-Clean (RAC) 419 RAC X SwitchTip produces an 8 to 10 inch fan and has a 0.019 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 20
• Maximum Fan Width (in): 8
• Maximum Fan Width (mm): 254

• Maximum Flow Rate (GPM): 0.38
• Maximum Flow Rate (L/min): 1.44

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 8
• Minimum Fan Width (mm): 203

• Orifice Diameter (in): 0.019

• Pattern Size (in): 8 to 10
• Pattern Size (mm): 203.2 to 254

GG LTX429

RAC X LTX TIP, SPRAY, LATEX, (429)

Graco LTX429 RAC X SwitchTip, 429

The Reverse-A-Clean (RAC) 429 RAC X SwitchTip produces an 8 to 10 inch fan and has a 0.029 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 20
• Maximum Fan Width (in): 8
• Maximum Fan Width (mm): 254

• Maximum Flow Rate (GPM): 0.90
• Maximum Flow Rate (L/min): 3.41

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 8
• Minimum Fan Width (mm): 203

• Orifice Diameter (in): 0.029

• Pattern Size (in): 8 to 10
• Pattern Size (mm): 203.2 to 254

GG LTX433

RAC X LTX TIP, SPRAY, (433)

Graco LTX433 RAC X SwitchTip, 433

The Reverse-A-Clean (RAC) 433 RAC X SwitchTip produces an 8 to 10 inch fan and has a 0.033 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 20
• Maximum Fan Width (in): 8
• Maximum Fan Width (mm): 254

• Maximum Flow Rate (GPM): 1.17
• Maximum Flow Rate (L/min): 4.43

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 8
• Minimum Fan Width (mm): 203

• Orifice Diameter (in): 0.033

• Pattern Size (in): 8 to 10
• Pattern Size (mm): 203.2 to 254

GG LTX545

RAC X LTX TIP, SPRAY, (545)

Graco LTX545 RAC X SwitchTip, 545

The Reverse-A-Clean (RAC) 545 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.045 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 25
• Maximum Fan Width (in): 10
• Maximum Fan Width (mm): 305

• Maximum Flow Rate (GPM): 2.17
• Maximum Flow Rate (L/min): 8.21

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 10
• Minimum Fan Width (mm): 254

• Orifice Diameter (in): 0.045

• Pattern Size (in): 10 to 12
• Pattern Size (mm): 254 to 304.8

GG LTX561

RAC X LTX TIP, SPRAY, (561)

Graco LTX561 RAC X SwitchTip, 561

The Reverse-A-Clean (RAC) 561 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.061 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 25
• Maximum Fan Width (in): 10
• Maximum Fan Width (mm): 305

• Maximum Flow Rate (GPM): 4.00
• Maximum Flow Rate (L/min): 15.14

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 10
• Minimum Fan Width (mm): 254

• Orifice Diameter (in): 0.061

• Pattern Size (in): 10 to 12
• Pattern Size (mm): 254 to 304.8

GG LTX521

RAC X LTX TIP, SPRAY, 521

Graco LTX521 RAC X SwitchTip, 521

The Reverse-A-Clean (RAC) 521 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.021 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Latex Paint, Latex Stain, Oil-Based Paint, Oil-Based Stain

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 25
• Maximum Fan Width (in): 10
• Maximum Fan Width (mm): 305

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 10
• Minimum Fan Width (mm): 254

• Orifice Diameter (in): 0.021

• Pattern Size (in): 10 to 12
• Pattern Size (mm): 254 to 304.8

GG LTX615

RAC X LTX TIP, SPRAY, 615

Graco LTX615 RAC X SwitchTip, 615

The Reverse-A-Clean (RAC) 615 RAC X SwitchTip produces a 12 to 14 inch fan and has a 0.015 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 30
• Maximum Fan Width (in): 12
• Maximum Fan Width (mm): 356

• Maximum Flow Rate (GPM): 0.24
• Maximum Flow Rate (L/min): 0.91

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 12
• Minimum Fan Width (mm): 305

• Orifice Diameter (in): 0.015

• Pattern Size (in): 12 to 14
• Pattern Size (mm): 304.8 to 355.6

GG LTX537

RAC X LTX TIP, SPRAY, (537)

Graco LTX537 RAC X SwitchTip, 537

The Reverse-A-Clean (RAC) 537 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.037 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 25
• Maximum Fan Width (in): 10
• Maximum Fan Width (mm): 305

• Maximum Flow Rate (GPM): 1.47
• Maximum Flow Rate (L/min): 5.56

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 10
• Minimum Fan Width (mm): 254

• Orifice Diameter (in): 0.037

• Pattern Size (in): 10 to 12
• Pattern Size (mm): 254 to 304.8

GG LTX611

RAC X LTX TIP, SPRAY, LATEX, (611)

Graco LTX611 RAC X SwitchTip, 611

The Reverse-A-Clean (RAC) 611 RAC X SwitchTip produces a 12 to 14 inch fan and has a 0.011 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 30
• Maximum Fan Width (in): 12
• Maximum Fan Width (mm): 356

• Maximum Flow Rate (GPM): 0.12
• Maximum Flow Rate (L/min): 0.45

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 12
• Minimum Fan Width (mm): 305

• Orifice Diameter (in): 0.011

• Pattern Size (in): 12 to 14
• Pattern Size (mm): 304.8 to 355.6

GG LTX613

RAC X LTX TIP, SPRAY, LATEX, (613)

Graco LTX613 RAC X SwitchTip, 613

The Reverse-A-Clean (RAC) 613 RAC X SwitchTip produces a 12 to 14 inch fan and has a 0.013 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 30
• Maximum Fan Width (in): 12
• Maximum Fan Width (mm): 356

• Maximum Flow Rate (GPM): 0.18
• Maximum Flow Rate (L/min): 0.68

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 12
• Minimum Fan Width (mm): 305

• Orifice Diameter (in): 0.013

• Pattern Size (in): 12 to 14
• Pattern Size (mm): 304.8 to 355.6

GG LTX539

RAC X LTX TIP, SPRAY, (539)

Graco LTX539 RAC X SwitchTip, 539

The Reverse-A-Clean (RAC) 539 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.039 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 25
• Maximum Fan Width (in): 10
• Maximum Fan Width (mm): 305

• Maximum Flow Rate (GPM): 1.63
• Maximum Flow Rate (L/min): 6.17

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 10
• Minimum Fan Width (mm): 254

• Orifice Diameter (in): 0.039

• Pattern Size (in): 10 to 12
• Pattern Size (mm): 254 to 304.8

GG LTX527

RAC X LTX TIP, SPRAY, 527

Graco LTX527 RAC X SwitchTip, 527

The Reverse-A-Clean (RAC) 527 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.027 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 25
• Maximum Fan Width (in): 10
• Maximum Fan Width (mm): 305

• Maximum Flow Rate (GPM): 0.77
• Maximum Flow Rate (L/min): 2.91

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 10
• Minimum Fan Width (mm): 254

• Orifice Diameter (in): 0.027

• Pattern Size (in): 10 to 12
• Pattern Size (mm): 254 to 304.8

GG LTX535

RAC X LTX TIP, SPRAY, 535

Graco LTX535 RAC X SwitchTip, 535

The Reverse-A-Clean (RAC) 535 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.035 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 25
• Maximum Fan Width (in): 10
• Maximum Fan Width (mm): 305

• Maximum Flow Rate (GPM): 1.31
• Maximum Flow Rate (L/min): 4.96

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 10
• Minimum Fan Width (mm): 254

• Orifice Diameter (in): 0.035

• Pattern Size (in): 10 to 12
• Pattern Size (mm): 254 to 304.8

GG LTX523

RAC X LTX TIP, SPRAY, 523

Graco LTX523 RAC X SwitchTip, 523

The Reverse-A-Clean (RAC) 523 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.023 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Best Tip on the Market

  Longest lasting fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: LTX SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC X HandTite Tip Guard

• Maximum Fan Width (cm): 25
• Maximum Fan Width (in): 10
• Maximum Fan Width (mm): 305

• Maximum Flow Rate (GPM): 0.57
• Maximum Flow Rate (L/min): 2.16

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 10
• Minimum Fan Width (mm): 254

• Orifice Diameter (in): 0.023

• Pattern Size (in): 10 to 12
• Pattern Size (mm): 254 to 304.8