Airpower | GRACO INC. S10595 branded products

GG LTX531

RAC X LTX TIP, SPRAY, 531

Graco LTX531 RAC X SwitchTip, 531

The Reverse-A-Clean (RAC) 531 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.031 inch orifice. Reverse the SwitchTip to easily clear clogs.

Application: Used for residential, commercial or industrial applications.

Best Tip on the Market
Longest lasting fan pattern
Highest quality finish with a consistent spray pattern
Easy to Identify Tip Size
Large raised tip size numbers are always legible - even when covered with paint
Superior Tip Design
Locking tab ensures tip stays securely in guard
Snaps tip in spray or reverse position
OneSeal tip gasket installs with no tools
Solvent seal available when using extremely hot solvents

Model: RAC X
Series: LTX SwitchTip

Compatible Material: Lacquer to Mastic, Latex Paint

For Use With: RAC X HandTite Tip Guard

Maximum Fan Width (cm): 25
Maximum Fan Width (in): 10
Maximum Fan Width (mm): 305

Maximum Flow Rate (GPM): 1.03
Maximum Flow Rate (L/min): 3.90

Maximum Working Pressure (bar): 280
Maximum Working Pressure (kPa): 28000
Maximum Working Pressure (psi): 4050

Minimum Fan Width (in): 10
Minimum Fan Width (mm): 254

Orifice Diameter (in): 0.031

Pattern Size (in): 10 to 12
Pattern Size (mm): 254 to 304.8

$65.25

GG LTX435

RAC X LTX TIP, SPRAY, LATEX, (435)

Graco LTX435 RAC X SwitchTip, 435

The Reverse-A-Clean (RAC) 435 RAC X SwitchTip produces an 8 to 10 inch fan and has a 0.035 inch orifice. Reverse the SwitchTip to easily clear clogs.

Application: Used for residential, commercial or industrial applications.

Best Tip on the Market
Longest lasting fan pattern
Highest quality finish with a consistent spray pattern
Easy to Identify Tip Size
Large raised tip size numbers are always legible - even when covered with paint
Superior Tip Design
Locking tab ensures tip stays securely in guard
Snaps tip in spray or reverse position
OneSeal tip gasket installs with no tools
Solvent seal available when using extremely hot solvents

Model: RAC X
Series: LTX SwitchTip

Compatible Material: Lacquer to Mastic, Latex Paint

For Use With: RAC X HandTite Tip Guard

Maximum Fan Width (cm): 20
Maximum Fan Width (in): 8
Maximum Fan Width (mm): 254

Maximum Flow Rate (GPM): 1.31
Maximum Flow Rate (L/min): 4.96

Maximum Working Pressure (bar): 280
Maximum Working Pressure (kPa): 28000
Maximum Working Pressure (psi): 4050

Minimum Fan Width (in): 8
Minimum Fan Width (mm): 203

Orifice Diameter (in): 0.035

Pattern Size (in): 8 to 10
Pattern Size (mm): 203.2 to 254

$65.25

GG LTX517

RAC X LTX TIP, SPRAY, 517

Graco LTX517 RAC X SwitchTip, 517

The Reverse-A-Clean (RAC) 517 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.017 inch orifice. Reverse the SwitchTip to easily clear clogs.

Application: Used for residential, commercial or industrial applications.

Best Tip on the Market
Longest lasting fan pattern
Highest quality finish with a consistent spray pattern
Easy to Identify Tip Size
Large raised tip size numbers are always legible - even when covered with paint
Superior Tip Design
Locking tab ensures tip stays securely in guard
Snaps tip in spray or reverse position
OneSeal tip gasket installs with no tools
Solvent seal available when using extremely hot solvents

Model: RAC X
Series: LTX SwitchTip

Compatible Material: Latex Paint, Latex Stain, Oil-Based Paint, Oil-Based Stain

For Use With: RAC X HandTite Tip Guard

Material: Tungsten Carbide

Maximum Fan Width (cm): 25
Maximum Fan Width (in): 10
Maximum Fan Width (mm): 305

Maximum Working Pressure (bar): 280
Maximum Working Pressure (kPa): 28000
Maximum Working Pressure (psi): 4050

Minimum Fan Width (in): 10
Minimum Fan Width (mm): 254

Orifice Diameter (in): 0.017

Pattern Size (in): 10 to 12
Pattern Size (mm): 254 to 304.8

$65.25

GG LTX515

RAC X LTX TIP, SPRAY, 515

Graco LTX515 RAC X SwitchTip, 515

The Reverse-A-Clean (RAC) 515 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.015 inch orifice. Reverse the SwitchTip to easily clear clogs.

Application: Used for residential, commercial or industrial applications.

Best Tip on the Market
Longest lasting fan pattern
Highest quality finish with a consistent spray pattern
Easy to Identify Tip Size
Large raised tip size numbers are always legible - even when covered with paint
Superior Tip Design
Locking tab ensures tip stays securely in guard
Snaps tip in spray or reverse position
OneSeal tip gasket installs with no tools
Solvent seal available when using extremely hot solvents

Model: RAC X
Series: LTX SwitchTip

Compatible Material: Latex Paint, Latex Stain, Oil-Based Paint, Oil-Based Stain

For Use With: RAC X HandTite Tip Guard

Material: Tungsten Carbide

Maximum Fan Width (cm): 25
Maximum Fan Width (in): 10
Maximum Fan Width (mm): 305

Maximum Working Pressure (bar): 280
Maximum Working Pressure (kPa): 28000
Maximum Working Pressure (psi): 4050

Minimum Fan Width (in): 10
Minimum Fan Width (mm): 254

Orifice Diameter (in): 0.015

Pattern Size (in): 10 to 12
Pattern Size (mm): 254 to 304.8

$65.25

GG LTX525

RAC X LTX TIP, SPRAY, 525

Graco LTX525 RAC X SwitchTip, 525

The Reverse-A-Clean (RAC) 525 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.025 inch orifice. Reverse the SwitchTip to easily clear clogs.

Application: Used for residential, commercial or industrial applications.

Best Tip on the Market
Longest lasting fan pattern
Highest quality finish with a consistent spray pattern
Easy to Identify Tip Size
Large raised tip size numbers are always legible - even when covered with paint
Superior Tip Design
Locking tab ensures tip stays securely in guard
Snaps tip in spray or reverse position
OneSeal tip gasket installs with no tools
Solvent seal available when using extremely hot solvents

Model: RAC X
Series: LTX SwitchTip

Compatible Material: Lacquer to Mastic, Latex Paint

For Use With: RAC X HandTite Tip Guard

Maximum Fan Width (cm): 25
Maximum Fan Width (in): 10
Maximum Fan Width (mm): 305

Maximum Flow Rate (GPM): 0.67
Maximum Flow Rate (L/min): 2.54

Maximum Working Pressure (bar): 280
Maximum Working Pressure (kPa): 28000
Maximum Working Pressure (psi): 4050

Minimum Fan Width (in): 10
Minimum Fan Width (mm): 254

Orifice Diameter (in): 0.025

Pattern Size (in): 10 to 12
Pattern Size (mm): 254 to 304.8

$65.25

GG LTX509

RAC X LTX TIP, SPRAY, LATEX, (509)

Graco LTX509 RAC X SwitchTip, 509

The Reverse-A-Clean (RAC) 509 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.009 inch orifice. Reverse the SwitchTip to easily clear clogs.

Application: Used for residential, commercial or industrial applications.

Best Tip on the Market
Longest lasting fan pattern
Highest quality finish with a consistent spray pattern
Easy to Identify Tip Size
Large raised tip size numbers are always legible - even when covered with paint
Superior Tip Design
Locking tab ensures tip stays securely in guard
Snaps tip in spray or reverse position
OneSeal tip gasket installs with no tools
Solvent seal available when using extremely hot solvents

Model: RAC X
Series: LTX SwitchTip

Compatible Material: Lacquer to Mastic, Latex Paint

For Use With: RAC X HandTite Tip Guard

Maximum Fan Width (cm): 25
Maximum Fan Width (in): 10
Maximum Fan Width (mm): 305

Maximum Flow Rate (GPM): 0.09
Maximum Flow Rate (L/min): 0.34

Maximum Working Pressure (bar): 280
Maximum Working Pressure (kPa): 28000
Maximum Working Pressure (psi): 4050

Minimum Fan Width (in): 10
Minimum Fan Width (mm): 254

Orifice Diameter (in): 0.009

Pattern Size (in): 10 to 12
Pattern Size (mm): 254 to 304.8

$65.25

GG LTX519

RAC X LTX TIP, SPRAY, 519

Graco LTX519 RAC X SwitchTip, 519

The Reverse-A-Clean (RAC) 519 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.019 inch orifice. Reverse the SwitchTip to easily clear clogs.

Application: Used for residential, commercial or industrial applications.

Best Tip on the Market
Longest lasting fan pattern
Highest quality finish with a consistent spray pattern
Easy to Identify Tip Size
Large raised tip size numbers are always legible - even when covered with paint
Superior Tip Design
Locking tab ensures tip stays securely in guard
Snaps tip in spray or reverse position
OneSeal tip gasket installs with no tools
Solvent seal available when using extremely hot solvents

Model: RAC X
Series: LTX SwitchTip

Compatible Material: Latex Paint, Latex Stain, Oil-Based Paint, Oil-Based Stain

For Use With: RAC X HandTite Tip Guard

Material: Tungsten Carbide

Maximum Fan Width (cm): 25
Maximum Fan Width (in): 10
Maximum Fan Width (mm): 305

Maximum Working Pressure (bar): 280
Maximum Working Pressure (kPa): 28000
Maximum Working Pressure (psi): 4050

Minimum Fan Width (in): 10
Minimum Fan Width (mm): 254

Orifice Diameter (in): 0.019

Pattern Size (in): 10 to 12
Pattern Size (mm): 254 to 304.8

$65.25

GG LTX541

RAC X LTX TIP, SPRAY, (541)

Graco LTX541 RAC X SwitchTip, 541

The Reverse-A-Clean (RAC) 541 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.041 inch orifice. Reverse the SwitchTip to easily clear clogs.

Application: Used for residential, commercial or industrial applications.

Best Tip on the Market
Longest lasting fan pattern
Highest quality finish with a consistent spray pattern
Easy to Identify Tip Size
Large raised tip size numbers are always legible - even when covered with paint
Superior Tip Design
Locking tab ensures tip stays securely in guard
Snaps tip in spray or reverse position
OneSeal tip gasket installs with no tools
Solvent seal available when using extremely hot solvents

Model: RAC X
Series: LTX SwitchTip

Compatible Material: Lacquer to Mastic, Latex Paint

For Use With: RAC X HandTite Tip Guard

Maximum Fan Width (cm): 25
Maximum Fan Width (in): 10
Maximum Fan Width (mm): 305

Maximum Flow Rate (GPM): 1.80
Maximum Flow Rate (L/min): 6.81

Maximum Working Pressure (bar): 280
Maximum Working Pressure (kPa): 28000
Maximum Working Pressure (psi): 4050

Minimum Fan Width (in): 10
Minimum Fan Width (mm): 254

Orifice Diameter (in): 0.041

Pattern Size (in): 10 to 12
Pattern Size (mm): 254 to 304.8

$65.25

GG LTX511

RAC X LTX TIP, SPRAY, 511

Graco LTX511 RAC X SwitchTip, 511

The Reverse-A-Clean (RAC) 511 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.011 inch orifice. Reverse the SwitchTip to easily clear clogs.

Application: Used for residential, commercial or industrial applications.

Best Tip on the Market
Longest lasting fan pattern
Highest quality finish with a consistent spray pattern
Easy to Identify Tip Size
Large raised tip size numbers are always legible - even when covered with paint
Superior Tip Design
Locking tab ensures tip stays securely in guard
Snaps tip in spray or reverse position
OneSeal tip gasket installs with no tools
Solvent seal available when using extremely hot solvents

Model: RAC X
Series: LTX SwitchTip

Compatible Material: Lacquer to Mastic, Latex Paint

For Use With: RAC X HandTite Tip Guard

Maximum Fan Width (cm): 25
Maximum Fan Width (in): 10
Maximum Fan Width (mm): 305

Maximum Flow Rate (GPM): 0.12
Maximum Flow Rate (L/min): 0.45

Maximum Working Pressure (bar): 280
Maximum Working Pressure (kPa): 28000
Maximum Working Pressure (psi): 4050

Minimum Fan Width (in): 10
Minimum Fan Width (mm): 254

Orifice Diameter (in): 0.011

Pattern Size (in): 10 to 12
Pattern Size (mm): 254 to 304.8

$65.25

GG LTX513

RAC X LTX TIP, SPRAY, 513

Graco LTX513 RAC X SwitchTip, 513

The Reverse-A-Clean (RAC) 513 RAC X SwitchTip produces a 10 to 12 inch fan and has a 0.013 inch orifice. Reverse the SwitchTip to easily clear clogs.

Application: Used for residential, commercial or industrial applications.

Best Tip on the Market
Longest lasting fan pattern
Highest quality finish with a consistent spray pattern
Easy to Identify Tip Size
Large raised tip size numbers are always legible - even when covered with paint
Superior Tip Design
Locking tab ensures tip stays securely in guard
Snaps tip in spray or reverse position
OneSeal tip gasket installs with no tools
Solvent seal available when using extremely hot solvents

Model: RAC X
Series: LTX SwitchTip

Compatible Material: Latex Paint, Latex Stain, Oil-Based Paint, Oil-Based Stain

For Use With: RAC X HandTite Tip Guard

Maximum Fan Width (cm): 25
Maximum Fan Width (in): 10
Maximum Fan Width (mm): 305

Maximum Working Pressure (bar): 280
Maximum Working Pressure (kPa): 28000
Maximum Working Pressure (psi): 4050

Minimum Fan Width (in): 10
Minimum Fan Width (mm): 254

Orifice Diameter (in): 0.013

Pattern Size (in): 10 to 12
Pattern Size (mm): 254 to 304.8

$65.25

GG JK-2001

KIT,REPAIR,JET

KIT INCLUDES: BEARING, PIN, DIAPHRAGM [QTY. 1], SEAL, HEATER [QTY. 1], LEVER, [QTY. 1], SOLENOID, MAIN AIR [QTY. 1], SPRING, COMP, .296ODX.246ID, 5.4LB/ [QTY. 1], SCREW, SHC, SHLDR, .25ODX.652L [QTY. 1], MUFFLER, AIR, #10-32, BRONZE [QTY. 1], WASHER, FLAT, #12, NYLON, BLACK [QTY. 1], CYLINDER, ASSEMBLY, HAMMER [QTY. 1]

$915.00

High-Flo Pump, 4000, Ln, Sld, Tri

GG JS17A8

HIGH-FLO PUMP, 4000, LN, SLD, TRI

Graco JS17A8 High-Flo 4-Ball Pump, SST, 1.7:1, Low Noise XL, Sealed SST Lower, Ultralife Rod/Cylinder, Tri-Clamp

Pneumatic High-Flo 4-ball piston pumps provide high output per cycle to reduce pump wear and maintenance. Ideal for low pressure, high flow applications and inherently safe for hazardous locations.

Slow-moving reciprocating motion does not damage paint like other rotary pumping technologies
Completely sealed fluid section can be used almost anywhere, including catalyst and moisture sensitive materials
Ultralife Series ceramic coating holds up to the harshest materials, including waterborne paints
Rugged body armor, won't rust or dent

Model: High-Flo
Series: 4-Ball

Application: Circulation

Compatible Material: Waterborne, Solvent borne, High Solids, Xirallic, Metallics, Topcoats, Stains, Varnish, CARC

Fluid Outlet Size (in): 1.5
Fluid Outlet Size (mm): 38.1
Fluid Section Type: Sealed

Includes: Stainless Steel Pump, Low Noise Exhaust, Tri-Clamp Fittings, Ultralife Rod, Ultralife Cylinder

Material: Stainless Steel

Maximum Air Inlet Pressure (bar): 6.9
Maximum Air Inlet Pressure (kPa): 690
Maximum Air Inlet Pressure (psi): 100

Maximum Continuous Cycle Rate (CPM): 20

Maximum Flow Rate (GPM): 21.1
Maximum Flow Rate (L/min): 80

Maximum Operating Temperature ( degree C): 60
Maximum Operating Temperature ( degree F): 140

Maximum Working Pressure (bar): 11.7
Maximum Working Pressure (kPa): 1170
Maximum Working Pressure (MPa): 1.2
Maximum Working Pressure (psi): 170

Motor Type: Low Noise XL

Portable: Non-Portable

Pump Ratio: 1.7:1

$29,220.00

High-Flo 4-Ball Pump, SST, 3.3:1, Low Noise XL, Sealed SST Lower, Ultralife Rod/Cylinder, Tri-Clamp

GG JS33A8

HIGH-FLO PUMP, 4000, LN, SLD, TRI

Graco JS33A8 High-Flo 4-Ball Pump, SST, 3.3:1, Low Noise XL, Sealed SST Lower, Ultralife Rod/Cylinder, Tri-Clamp

Pneumatic High-Flo 4-ball piston pumps provide high output per cycle to reduce pump wear and maintenance. Ideal for low pressure, high flow applications and inherently safe for hazardous locations.

Slow-moving reciprocating motion does not damage paint like other rotary pumping technologies
Completely sealed fluid section can be used almost anywhere, including catalyst and moisture sensitive materials
Ultralife Series ceramic coating holds up to the harshest materials, including waterborne paints
Rugged body armor, won't rust or dent

Model: High-Flo
Series: 4-Ball

Application: Circulation

Compatible Material: Waterborne, Solvent borne, High Solids, Xirallic, Metallics, Topcoats, Stains, Varnish, CARC

Fluid Outlet Size (in): 1.5
Fluid Outlet Size (mm): 50.8
Fluid Section Type: Sealed

Includes: Stainless Steel Pump, Low Noise Exhaust, Tri-Clamp Fittings, Ultralife Rod, Ultralife Cylinder

Material: Stainless Steel

Maximum Air Inlet Pressure (bar): 6.9
Maximum Air Inlet Pressure (kPa): 690
Maximum Air Inlet Pressure (psi): 100

Maximum Continuous Cycle Rate (CPM): 20

Maximum Flow Rate (GPM): 21.1
Maximum Flow Rate (L/min): 80

Maximum Operating Temperature ( degree C): 60
Maximum Operating Temperature ( degree F): 140

Maximum Working Pressure (bar): 22.7
Maximum Working Pressure (kPa): 2275
Maximum Working Pressure (MPa): 2.3
Maximum Working Pressure (psi): 330

Motor Type: Low Noise XL

Portable: Non-Portable

Pump Ratio: 3.3:1

$33,110.00

High-Flo 4-Ball Pump, SST, 3.3:1, Low Noise, DataTrak, Sealed SST Lower, Ultralife Rod/Cylinder

GG JS33B8

HIGH-FLO PUMP, 4000, LN DT, SLD, TRI

Graco JS33B8 High-Flo 4-Ball Pump, SST, 3.3:1, Low Noise, DataTrak, Sealed SST Lower, Ultralife Rod/Cylinder, Tri-Clamp

Pneumatic High-Flo 4-ball piston pumps provide high output per cycle to reduce pump wear and maintenance. Ideal for low pressure, high flow applications and inherently safe for hazardous locations.

Slow-moving reciprocating motion does not damage paint like other rotary pumping technologies
Completely sealed fluid section can be used almost anywhere, including catalyst and moisture sensitive materials
Ultralife Series ceramic coating holds up to the harshest materials, including waterborne paints
Rugged body armor, won't rust or dent
DataTrak tracks material usage, monitors and protects your pump

Model: High-Flo
Series: 4-Ball

Application: Circulation

Compatible Material: Waterborne, Solvent borne, High Solids, Xirallic, Metallics, Topcoats, Stains, Varnish, CARC

Fluid Outlet Size (in): 1.5
Fluid Outlet Size (mm): 50.8
Fluid Section Type: Sealed

Includes: Stainless Steel Pump, Low Noise Exhaust, DataTrak Monitor, Tri-Clamp Fittings, Ultralife Rod, Ultralife Cylinder

Material: Stainless Steel

Maximum Air Inlet Pressure (bar): 6.9
Maximum Air Inlet Pressure (kPa): 690
Maximum Air Inlet Pressure (psi): 100

Maximum Continuous Cycle Rate (CPM): 20

Maximum Flow Rate (GPM): 21.1
Maximum Flow Rate (L/min): 80

Maximum Operating Temperature ( degree C): 60
Maximum Operating Temperature ( degree F): 140

Maximum Working Pressure (bar): 22.7
Maximum Working Pressure (kPa): 2275
Maximum Working Pressure (MPa): 2.3
Maximum Working Pressure (psi): 330

Motor Type: Low Noise with DataTrak

Portable: Non-Portable

Pump Ratio: 3.3:1

$36,180.00

High-Flo Pump, Xl34/2000, Ln, Sld, Tri

GG JS35A8

HIGH-FLO PUMP, XL34/2000, LN, SLD, TRI

Graco JS35A8 High-Flo 4-Ball Pump, SST, 3.5:1, Low Noise XL, Sealed SST Lower, Ultralife Rod/Cylinder, Tri-Clamp

Pneumatic High-Flo 4-ball piston pumps provide high output per cycle to reduce pump wear and maintenance. Ideal for low pressure, high flow applications and inherently safe for hazardous locations.

Slow-moving reciprocating motion does not damage paint like other rotary pumping technologies
Completely sealed fluid section can be used almost anywhere, including catalyst and moisture sensitive materials
Ultralife Series ceramic coating holds up to the harshest materials, including waterborne paints
Rugged body armor, won't rust or dent

Model: High-Flo
Series: 4-Ball

Application: Circulation

Compatible Material: Waterborne, Solvent borne, High Solids, Xirallic, Metallics, Topcoats, Stains, Varnish, CARC

Fluid Outlet Size (in): 1.5
Fluid Outlet Size (mm): 38.1
Fluid Section Type: Sealed

Includes: Stainless Steel Pump, Low Noise Exhaust, Tri-Clamp Fittings, Ultralife Rod, Ultralife Cylinder

Material: Stainless Steel

Maximum Air Inlet Pressure (bar): 6.9
Maximum Air Inlet Pressure (kPa): 690
Maximum Air Inlet Pressure (psi): 100

Maximum Continuous Cycle Rate (CPM): 20

Maximum Flow Rate (GPM): 10.6
Maximum Flow Rate (L/min): 40

Maximum Operating Temperature ( degree C): 60
Maximum Operating Temperature ( degree F): 140

Maximum Working Pressure (bar): 24.1
Maximum Working Pressure (kPa): 2410
Maximum Working Pressure (MPa): 2.4
Maximum Working Pressure (psi): 350

Motor Type: Low Noise XL

Portable: Non-Portable

Pump Ratio: 3.5:1

$19,560.00

High-Flo Pump, Xl34/2000, Ln, Dt, Sld, Tri

GG JS35B8

HIGH-FLO PUMP, XL34/2000, LN, DT, SLD, TRI

Graco JS35B8 High-Flo 4-Ball Pump, SST, 3.5:1, Low Noise, DataTrak, Sealed SST Lower, Ultralife Rod/Cylinder, Tri-Clamp

Pneumatic High-Flo 4-ball piston pumps provide high output per cycle to reduce pump wear and maintenance. Ideal for low pressure, high flow applications and inherently safe for hazardous locations.

Slow-moving reciprocating motion does not damage paint like other rotary pumping technologies
Completely sealed fluid section can be used almost anywhere, including catalyst and moisture sensitive materials
Ultralife Series ceramic coating holds up to the harshest materials, including waterborne paints
Rugged body armor, won't rust or dent
DataTrak tracks material usage, monitors and protects your pump

Model: High-Flo
Series: 4-Ball

Application: Circulation

Compatible Material: Waterborne, Solvent borne, High Solids, Xirallic, Metallics, Topcoats, Stains, Varnish, CARC

Fluid Outlet Size (in): 1.5
Fluid Outlet Size (mm): 38.1
Fluid Section Type: Sealed

Includes: Stainless Steel Pump, Low Noise Exhaust, DataTrak Monitor, Tri-Clamp Fittings, Ultralife Rod, Ultralife Cylinder

Material: Stainless Steel

Maximum Air Inlet Pressure (bar): 6.9
Maximum Air Inlet Pressure (kPa): 690
Maximum Air Inlet Pressure (psi): 100

Maximum Continuous Cycle Rate (CPM): 20

Maximum Flow Rate (GPM): 10.6
Maximum Flow Rate (L/min): 40

Maximum Operating Temperature ( degree C): 60
Maximum Operating Temperature ( degree F): 140

Maximum Working Pressure (bar): 24.1
Maximum Working Pressure (kPa): 2410
Maximum Working Pressure (MPa): 2.4
Maximum Working Pressure (psi): 350

Motor Type: Low Noise with DataTrak

Portable: Non-Portable

Pump Ratio: 3.5:1

$21,940.00

High-Flo Pump, 2200/1000, Low N, Sld, Tri

GG JS40L8

HIGH-FLO PUMP, 2200/1000, LOW N, SLD, TRI

Graco JS40L8 High-Flo 4-Ball Pump, SST, 4:1, Low Noise Exhaust, Sealed SST Lower, Tri-Clamp Fittings, Ultralife Rod/Cylinder

Pneumatic High-Flo 4-ball piston pumps provide high output per cycle to reduce pump wear and maintenance. Ideal for low pressure, high flow applications and inherently safe for hazardous locations.

Slow-moving reciprocating motion does not damage paint like other rotary pumping technologies
Completely sealed fluid section can be used almost anywhere, including catalyst and moisture sensitive materials
Ultralife Series ceramic coating holds up to the harshest materials, including waterborne paints
Rugged body armor, won't rust or dent

Model: High-Flo
Series: 4-Ball

Application: Circulation

Compatible Material: Waterborne, Solvent borne, High Solids, Xirallic, Metallics, Topcoats, Stains, Varnish, CARC

Fluid Outlet Size (in): 1-1/2
Fluid Outlet Size (mm): 38.1
Fluid Section Type: Sealed

Includes: Stainless Steel Pump, Low Noise Exhaust, Tri-Clamp Fittings, Ultralife Rod, Ultralife Cylinder

Material: Stainless Steel

Maximum Air Inlet Pressure (bar): 6.9
Maximum Air Inlet Pressure (kPa): 690
Maximum Air Inlet Pressure (psi): 100

Maximum Continuous Cycle Rate (CPM): 20

Maximum Flow Rate (GPM): 16.9
Maximum Flow Rate (L/min): 63.97

Maximum Operating Temperature ( degree C): 66
Maximum Operating Temperature ( degree F): 150

Maximum Working Pressure (bar): 28
Maximum Working Pressure (kPa): 2800
Maximum Working Pressure (MPa): 2.8
Maximum Working Pressure (psi): 400

Motor Type: Low Noise NXT

Portable: Non-Portable

Pump Ratio: 4:1

$15,740.00

High-Flo Pump, 2200/1000, Low Dt, Sld, Tri

GG JS40M8

HIGH-FLO PUMP, 2200/1000, LOW DT, SLD, TRI

Graco JS40M8 High-Flo 4-Ball Pump, SST, 4:1, Low Noise Exhaust, DataTrak, Sealed SST Lower, Tri-Clamp Fittings, Ultralife Rod/Cylinder

Pneumatic High-Flo 4-ball piston pumps provide high output per cycle to reduce pump wear and maintenance. Ideal for low pressure, high flow applications and inherently safe for hazardous locations.

Slow-moving reciprocating motion does not damage paint like other rotary pumping technologies
Completely sealed fluid section can be used almost anywhere, including catalyst and moisture sensitive materials
Ultralife Series ceramic coating holds up to the harshest materials, including waterborne paints
Rugged body armor, won't rust or dent
DataTrak tracks material usage, monitors and protects your pump

Model: High-Flo
Series: 4-Ball

Application: Circulation

Compatible Material: Waterborne, Solvent borne, High Solids, Xirallic, Metallics, Topcoats, Stains, Varnish, CARC

Fluid Outlet Size (in): 1-1/2
Fluid Outlet Size (mm): 38.1
Fluid Section Type: Sealed

Includes: Stainless Steel Pump, Low Noise Exhaust, DataTrak Monitor, Tri-Clamp Fittings, Ultralife Rod, Ultralife Cylinder

Material: Stainless Steel

Maximum Air Inlet Pressure (bar): 6.9
Maximum Air Inlet Pressure (kPa): 690
Maximum Air Inlet Pressure (psi): 100

Maximum Continuous Cycle Rate (CPM): 20

Maximum Flow Rate (GPM): 16.9
Maximum Flow Rate (L/min): 63.97

Maximum Operating Temperature ( degree C): 66
Maximum Operating Temperature ( degree F): 150

Maximum Working Pressure (bar): 28
Maximum Working Pressure (kPa): 2800
Maximum Working Pressure (MPa): 2.8
Maximum Working Pressure (psi): 400

Motor Type: Low Noise NXT with DataTrak

Portable: Non-Portable

Pump Ratio: 4:1

$16,290.00

High-Flo Pump, 3000, Ln, Sld, Tri

GG JS44A8

HIGH-FLO PUMP, 3000, LN, SLD, TRI

Graco JS44A8 High-Flo 4-Ball Pump, SST, 4.4:1, Low Noise XL, Sealed SST Lower, Ultralife Rod/Cylinder, Tri-Clamp

Pneumatic High-Flo 4-ball piston pumps provide high output per cycle to reduce pump wear and maintenance. Ideal for low pressure, high flow applications and inherently safe for hazardous locations.

Slow-moving reciprocating motion does not damage paint like other rotary pumping technologies
Completely sealed fluid section can be used almost anywhere, including catalyst and moisture sensitive materials
Ultralife Series ceramic coating holds up to the harshest materials, including waterborne paints
Rugged body armor, won't rust or dent

Model: High-Flo
Series: 4-Ball

Application: Circulation

Compatible Material: Waterborne, Solvent borne, High Solids, Xirallic, Metallics, Topcoats, Stains, Varnish, CARC

Fluid Outlet Size (in): 1.5
Fluid Outlet Size (mm): 38.1
Fluid Section Type: Sealed

Includes: Stainless Steel Pump, Low Noise Exhaust, Tri-Clamp Fittings, Ultralife Rod, Ultralife Cylinder

Material: Stainless Steel

Maximum Air Inlet Pressure (bar): 6.9
Maximum Air Inlet Pressure (kPa): 690
Maximum Air Inlet Pressure (psi): 100

Maximum Continuous Cycle Rate (CPM): 20

Maximum Flow Rate (GPM): 15.9
Maximum Flow Rate (L/min): 60

Maximum Operating Temperature ( degree C): 60
Maximum Operating Temperature ( degree F): 140

Maximum Working Pressure (bar): 30.3
Maximum Working Pressure (kPa): 3030
Maximum Working Pressure (MPa): 3
Maximum Working Pressure (psi): 440

Motor Type: Low Noise XL

Portable: Non-Portable

Pump Ratio: 4.4:1

$32,210.00

High-Flo Pump, 3000, Ln Dt, Sld, Tri

GG JS44B8

HIGH-FLO PUMP, 3000, LN DT, SLD, TRI

Graco JS44B8 High-Flo 4-Ball Pump, SST, 4.4:1, Low Noise, DataTrak, Sealed SST Lower, Ultralife Rod/Cylinder, Tri-Clamp

Pneumatic High-Flo 4-ball piston pumps provide high output per cycle to reduce pump wear and maintenance. Ideal for low pressure, high flow applications and inherently safe for hazardous locations.

Slow-moving reciprocating motion does not damage paint like other rotary pumping technologies
Completely sealed fluid section can be used almost anywhere, including catalyst and moisture sensitive materials
Ultralife Series ceramic coating holds up to the harshest materials, including waterborne paints
Rugged body armor, won't rust or dent
DataTrak tracks material usage, monitors and protects your pump

Model: High-Flo
Series: 4-Ball

Application: Circulation

Compatible Material: Waterborne, Solvent borne, High Solids, Xirallic, Metallics, Topcoats, Stains, Varnish, CARC

Fluid Outlet Size (in): 1.5
Fluid Outlet Size (mm): 38.1
Fluid Section Type: Sealed

Includes: Stainless Steel Pump, Low Noise Exhaust, DataTrak Monitor, Tri-Clamp Fittings, Ultralife Rod, Ultralife Cylinder

Material: Stainless Steel

Maximum Air Inlet Pressure (bar): 6.9
Maximum Air Inlet Pressure (kPa): 690
Maximum Air Inlet Pressure (psi): 100

Maximum Continuous Cycle Rate (CPM): 20

Maximum Flow Rate (GPM): 15.9
Maximum Flow Rate (L/min): 60

Maximum Operating Temperature ( degree C): 60
Maximum Operating Temperature ( degree F): 140

Maximum Working Pressure (bar): 30.3
Maximum Working Pressure (kPa): 3030
Maximum Working Pressure (MPa): 3
Maximum Working Pressure (psi): 440

Motor Type: Low Noise with DataTrak

Portable: Non-Portable

Pump Ratio: 4.4:1

$35,290.00

High-Flo Pump, 3000, Rem Dt, Sld, Tri

GG JS44D8

High-Flo Pump, 3000, Rem Dt, Sld, Tri

$0.00

High-Flo Pump, Xl34/1500, Ln, Opn, Npt

GG JS45A9

HIGH-FLO PUMP, XL34/1500, LN, OPN, NPT

Graco JS45A9 High-Flo 4-Ball Pump, SST, 4.5:1, Low Noise XL, Open Wet Cup SST Lower, Ultralife Rod/Cylinder, NPT

Pneumatic High-Flo 4-ball piston pumps provide high output per cycle to reduce pump wear and maintenance. Ideal for low pressure, high flow applications and inherently safe for hazardous locations.

Slow-moving reciprocating motion does not damage paint like other rotary pumping technologies
Rugged body armor, won't rust or dent
De-icing controls eliminate stalling

Model: High-Flo
Series: 4-Ball

Application: Circulation

Fluid Outlet Size (in): 1.5
Fluid Outlet Size (mm): 38.1
Fluid Section Type: Open Wet Cup

Includes: Stainless Steel Pump, Low Noise Exhaust, NPT Fittings, Ultralife Rod, Ultralife Cylinder

Material: Stainless Steel

Maximum Air Inlet Pressure (bar): 6.9
Maximum Air Inlet Pressure (kPa): 690
Maximum Air Inlet Pressure (psi): 100

Maximum Continuous Cycle Rate (CPM): 12

Maximum Flow Rate (GPM): 4.8
Maximum Flow Rate (L/min): 18

Maximum Operating Temperature ( degree C): 60
Maximum Operating Temperature ( degree F): 140

Maximum Working Pressure (bar): 31
Maximum Working Pressure (kPa): 3100
Maximum Working Pressure (MPa): 3.1
Maximum Working Pressure (psi): 450

Motor Type: Low Noise XL

Portable: Non-Portable

Pump Ratio: 4.5:1

$15,770.00

King Sprayer, 25:1, H-P, Bf, Wall, Bare

GG K25FW0

KING SPRAYER, 25:1, H-P, BF, WALL, BARE

Graco K25FW0 Discontinued: King 25:1 Sprayer, Integrated Filter, Wall Mount, Air Controls, Siphon Kit

Product replaced by newer version, see part number K30FW0

Application: High-quality, high-volume, high-pressure. The Graco King pneumatic airless sprayers are the most powerful machines for protective coatings. The system provides the applicator output values, pressure ratios and pumping capacities never seen before. The Graco King units are designed to withstand the harshest environmental conditions and easily handle the toughest protective coatings and corrosion control applications. With 10 different ratios available, there is a sprayer with the correct pressure and flow characteristics for your application.

Simple Maintenance
- Improved Icing Performance
  - Less Pulsation
    With more than 145% higher exhaust capacity in the air valve, youll achieve a faster, smoother changeover.
    Eliminating the winkin your pattern - it is a difference you will feel.
  - New Air Motor
    Multi gun capabilities Graco's powerful new air motor lets you use multiple guns with almost no perceivable pulsation. A new manifold has been designed to simplify the installation of multiple guns.

$0.00

King Sprayer, 30:1, H-P, Bf, Wall, Bare

GG K30FW0

KING SPRAYER, 30:1, H-P, BF, WALL, BARE

Graco K30FW0 King 30:1 Sprayer, Integrated Filter, Wall Mount, Air Controls, Siphon Kit

High-quality, high-volume, high-pressure. The Graco King pneumatic airless sprayers are the most powerful machines for protective coatings. The system provides the applicator output values, pressure ratios and pumping capacities never seen before. The Graco King units are designed to withstand the harshest environmental conditions and easily handle the toughest protective coatings and corrosion control applications. With 10 different ratios available, there is a sprayer with the correct pressure and flow characteristics for your application.

Application: Superior air-operated pumps for high-volume and high-pressure waterproofing, fireproofing and protective coatings

Simple Maintenance
- Improved Icing Performance
  - Less Pulsation
    With more than 145% higher exhaust capacity in the air valve, youll achieve a faster, smoother changeover.
    Eliminating the winkin your pattern - it is a difference you will feel.
  - New Air Motor
    Multi gun capabilities Graco's powerful new air motor lets you use multiple guns with almost no perceivable pulsation. A new manifold has been designed to simplify the installation of multiple guns.

$10,640.00

King Sprayer, 30:1, H-P, Bf, Wall, Comp

GG K30FW1

KING SPRAYER, 30:1, H-P, BF, WALL, COMP

Graco K30FW1 King 30:1 Sprayer, Integrated Filter, Wall Mount, Air Controls, Siphon Kit, XTR-5+, 50 ft (15 m) Hose, 6 ft (1.8 m) Whip

High-quality, high-volume, high-pressure. The Graco King pneumatic airless sprayers are the most powerful machines for protective coatings. The system provides the applicator output values, pressure ratios and pumping capacities never seen before. The Graco King units are designed to withstand the harshest environmental conditions and easily handle the toughest protective coatings and corrosion control applications. With 10 different ratios available, there is a sprayer with the correct pressure and flow characteristics for your application.

Application: Superior air-operated pumps for high-volume and high-pressure waterproofing, fireproofing and protective coatings

Simple Maintenance
- Improved Icing Performance
  - Less Pulsation
    With more than 145% higher exhaust capacity in the air valve, youll achieve a faster, smoother changeover.
    Eliminating the winkin your pattern - it is a difference you will feel.
  - New Air Motor
    Multi gun capabilities Graco's powerful new air motor lets you use multiple guns with almost no perceivable pulsation. A new manifold has been designed to simplify the installation of multiple guns.

$11,460.00

King Sprayer, 40:1, H-P, Bf, Hd, Comp

GG K40FH1

KING SPRAYER, 40:1, H-P, BF, HD, COMP

Graco K40FH1 King 40:1 Sprayer, Integrated Filter, Heavy Duty Cart, Air Controls, Siphon Kit, XTR-5+, 50 ft (15 m) Hose, 6 ft (1.8 m) Whip

High-quality, high-volume, high-pressure. The Graco King pneumatic airless sprayers are the most powerful machines for protective coatings. The system provides the applicator output values, pressure ratios and pumping capacities never seen before. The Graco King units are designed to withstand the harshest environmental conditions and easily handle the toughest protective coatings and corrosion control applications. With 10 different ratios available, there is a sprayer with the correct pressure and flow characteristics for your application.

Application: Superior air-operated pumps for high-volume and high-pressure waterproofing, fireproofing and protective coatings

Simple Maintenance
- Improved Icing Performance
  - Less Pulsation
    With more than 145% higher exhaust capacity in the air valve, youll achieve a faster, smoother changeover.
    Eliminating the winkin your pattern - it is a difference you will feel.
  - New Air Motor
    Multi gun capabilities Graco's powerful new air motor lets you use multiple guns with almost no perceivable pulsation. A new manifold has been designed to simplify the installation of multiple guns.

$12,110.00

King Sprayer, 40:1, H-P, Nf, Hd, Bare

GG K40NH0

KING SPRAYER, 40:1, H-P, NF, HD, BARE

Graco K40NH0 Discontinued: King 40:1 Sprayer, Non-Filter, Heavy Duty Cart, Air Controls, Siphon Kit

Product replaced by newer version, see part number K40FH0

Application: Superior air-operated pumps for high-volume and high-pressure waterproofing, fireproofing and protective coatings

Simple Maintenance
- Improved Icing Performance
  - Less Pulsation
    With more than 145% higher exhaust capacity in the air valve, youll achieve a faster, smoother changeover.
    Eliminating the winkin your pattern - it is a difference you will feel.
  - New Air Motor
    Multi gun capabilities Graco's powerful new air motor lets you use multiple guns with almost no perceivable pulsation. A new manifold has been designed to simplify the installation of multiple guns.

$0.00

King Sprayer, 45:1, H-P, Bf, Hd, Bare

GG K45FH0

KING SPRAYER, 45:1, H-P, BF, HD, BARE

Graco K45FH0 King 45:1 Sprayer, Integrated Filter, Heavy Duty Cart, Air Controls, Siphon Kit

High-quality, high-volume, high-pressure. The Graco King pneumatic airless sprayers are the most powerful machines for protective coatings. The system provides the applicator output values, pressure ratios and pumping capacities never seen before. The Graco King units are designed to withstand the harshest environmental conditions and easily handle the toughest protective coatings and corrosion control applications. With 10 different ratios available, there is a sprayer with the correct pressure and flow characteristics for your application.

Application: Superior air-operated pumps for high-volume and high-pressure waterproofing, fireproofing and protective coatings

Simple Maintenance
- Improved Icing Performance
  - Less Pulsation
    With more than 145% higher exhaust capacity in the air valve, youll achieve a faster, smoother changeover.
    Eliminating the winkin your pattern - it is a difference you will feel.
  - New Air Motor
    Multi gun capabilities Graco's powerful new air motor lets you use multiple guns with almost no perceivable pulsation. A new manifold has been designed to simplify the installation of multiple guns.

$11,930.00

King Sprayer, 45:1, H-P, Bf, Hd, Comp

GG K45FH1

KING SPRAYER, 45:1, H-P, BF, HD, COMP

Graco K45FH1 King 45:1 Sprayer, Integrated Filter, Heavy Duty Cart, Air Controls, Siphon Kit, XTR-5+, 50 ft (15 m) Hose, 6 ft (1.8 m) Whip

High-quality, high-volume, high-pressure. The Graco King pneumatic airless sprayers are the most powerful machines for protective coatings. The system provides the applicator output values, pressure ratios and pumping capacities never seen before. The Graco King units are designed to withstand the harshest environmental conditions and easily handle the toughest protective coatings and corrosion control applications. With 10 different ratios available, there is a sprayer with the correct pressure and flow characteristics for your application.

Application: Superior air-operated pumps for high-volume and high-pressure waterproofing, fireproofing and protective coatings

Simple Maintenance
- Improved Icing Performance
  - Less Pulsation
    With more than 145% higher exhaust capacity in the air valve, youll achieve a faster, smoother changeover.
    Eliminating the winkin your pattern - it is a difference you will feel.
  - New Air Motor
    Multi gun capabilities Graco's powerful new air motor lets you use multiple guns with almost no perceivable pulsation. A new manifold has been designed to simplify the installation of multiple guns.

$12,770.00

King Sprayer, 45:1, H-P, Nf, Hd, Bare

GG K45NH0

KING SPRAYER, 45:1, H-P, NF, HD, BARE

Graco K45NH0 King 45:1 Sprayer, Non-Filter, Heavy Duty Cart, Air Controls, Siphon Kit

High-quality, high-volume, high-pressure. The Graco King pneumatic airless sprayers are the most powerful machines for protective coatings. The system provides the applicator output values, pressure ratios and pumping capacities never seen before. The Graco King units are designed to withstand the harshest environmental conditions and easily handle the toughest protective coatings and corrosion control applications. With 10 different ratios available, there is a sprayer with the correct pressure and flow characteristics for your application.

Application: Superior air-operated pumps for high-volume and high-pressure waterproofing, fireproofing and protective coatings

Simple Maintenance
- Improved Icing Performance
  - Less Pulsation
    With more than 145% higher exhaust capacity in the air valve, youll achieve a faster, smoother changeover.
    Eliminating the winkin your pattern - it is a difference you will feel.
  - New Air Motor
    Multi gun capabilities Graco's powerful new air motor lets you use multiple guns with almost no perceivable pulsation. A new manifold has been designed to simplify the installation of multiple guns.

$11,790.00

King Sprayer, 45:1, H-P, Nf, Hd, Comp

GG K45NH1

KING SPRAYER, 45:1, H-P, NF, HD, COMP

Graco K45NH1 King 45:1 Sprayer, Non-Filter, Heavy Duty Cart, Air Controls, Siphon Kit, XTR-5+, 50 ft (15 m) Hose, 6 ft (1.8 m) Whip

High-quality, high-volume, high-pressure. The Graco King pneumatic airless sprayers are the most powerful machines for protective coatings. The system provides the applicator output values, pressure ratios and pumping capacities never seen before. The Graco King units are designed to withstand the harshest environmental conditions and easily handle the toughest protective coatings and corrosion control applications. With 10 different ratios available, there is a sprayer with the correct pressure and flow characteristics for your application.

Application: Superior air-operated pumps for high-volume and high-pressure waterproofing, fireproofing and protective coatings

Simple Maintenance
- Improved Icing Performance
  - Less Pulsation
    With more than 145% higher exhaust capacity in the air valve, youll achieve a faster, smoother changeover.
    Eliminating the winkin your pattern - it is a difference you will feel.
  - New Air Motor
    Multi gun capabilities Graco's powerful new air motor lets you use multiple guns with almost no perceivable pulsation. A new manifold has been designed to simplify the installation of multiple guns.

$12,630.00

King Sprayer, 60:1, H-P, Bf, Hd, Bare

GG K60FH0

KING SPRAYER, 60:1, H-P, BF, HD, BARE

Graco K60FH0 King 60:1 Sprayer, Integrated Filter, Heavy Duty Cart, Air Controls, Siphon Kit

High-quality, high-volume, high-pressure. The Graco King pneumatic airless sprayers are the most powerful machines for protective coatings. The system provides the applicator output values, pressure ratios and pumping capacities never seen before. The Graco King units are designed to withstand the harshest environmental conditions and easily handle the toughest protective coatings and corrosion control applications. With 10 different ratios available, there is a sprayer with the correct pressure and flow characteristics for your application.

Application: Superior air-operated pumps for high-volume and high-pressure waterproofing, fireproofing and protective coatings

Simple Maintenance
- Improved Icing Performance
  - Less Pulsation
    With more than 145% higher exhaust capacity in the air valve, youll achieve a faster, smoother changeover.
    Eliminating the winkin your pattern - it is a difference you will feel.
  - New Air Motor
    Multi gun capabilities Graco's powerful new air motor lets you use multiple guns with almost no perceivable pulsation. A new manifold has been designed to simplify the installation of multiple guns.

$12,770.00

King Sprayer, 60:1, H-P, Bf, Hd, Comp

GG K60FH1

KING SPRAYER, 60:1, H-P, BF, HD, COMP

Graco K60FH1 King 60:1 Sprayer, Integrated Filter, Heavy Duty Cart, Air Controls, Siphon Kit, XTR-7+, 50 ft (15 m) Hose, 6 ft (1.8 m) Whip

High-quality, high-volume, high-pressure. The Graco King pneumatic airless sprayers are the most powerful machines for protective coatings. The system provides the applicator output values, pressure ratios and pumping capacities never seen before. The Graco King units are designed to withstand the harshest environmental conditions and easily handle the toughest protective coatings and corrosion control applications. With 10 different ratios available, there is a sprayer with the correct pressure and flow characteristics for your application.

Application: Superior air-operated pumps for high-volume and high-pressure waterproofing, fireproofing and protective coatings

Simple Maintenance
- Improved Icing Performance
  - Less Pulsation
    With more than 145% higher exhaust capacity in the air valve, youll achieve a faster, smoother changeover.
    Eliminating the winkin your pattern - it is a difference you will feel.
  - New Air Motor
    Multi gun capabilities Graco's powerful new air motor lets you use multiple guns with almost no perceivable pulsation. A new manifold has been designed to simplify the installation of multiple guns.

$13,640.00

Kit, Pump, 3:1, 125Cc, Ss, Std

GG W03EAS

Kit, Pump, 3:1, 125Cc, Ss, Std

$6,460.00

Kit, Pump, 15:1, 50Cc, Ss, Std

GG W15BAS

Kit, Pump, 15:1, 50Cc, Ss, Std

$3,990.00

IQ Dispense Valve, Tip-Seal, Ambient, 0.067In (1.7 mm ) Tip, 2.36In (60 mm )Nozzle, Remote Mount Solenoid

GG V25GT060DA

IQ TIP SEAL VALVE, 25, 1.7/T, 060, ADJ/RM, AMB

Graco V25GT060DA iQ Dispense Valve, Tip-Seal, Ambient, 0.067in (1.7mm) Tip, 2.36in (60mm) Nozzle, Remote Mount Solenoid

The iQ Tip Seal Dispense Valve offers high reliability for single component sealant and adhesive dispensing applications.

Maximize dispense time while minimizing maintenance costs and effort
Delivers precise, consistent dispensing with clean starts and stops
Ideal for low to high viscosity materials
Easy repeatable mounting for robotic and automated applications.
60mm nozzle is compatible with 60mm focal length vision systems

Air Inlet Size (in): 1/8
Air Inlet Thread Gender: Female
Air Inlet Thread Type: NPT

Ambient/Warm Melt/Hot Melt: Ambient
Applicator Type: Tip-Seal

Component Type: Single Component

Fluid Inlet Size (in): 1/4
Fluid Inlet Thread Gender: Female
Fluid Inlet Thread Type: NPT

Gun Activation: Automatic

Maximum Air Pressure (bar): 8.3

Maximum Air Pressure (MPa): 0.83
Maximum Air Pressure (psi): 120

Maximum Fluid Pressure (bar): 276
Maximum Fluid Pressure (MPa): 28
Maximum Fluid Pressure (psi): 4000

Mount Location: Remote Mount Solenoid
Nozzle Size (in): 0.067
Nozzle Size (mm): 1.7

Outlet Block Length (in): 2.4
Outlet Block Length (mm): 60

$0.00

Tip, Spray Cylinder, (217)

GG XHD217

XHD RAC TIP, SPRAY, CYLINDER, 217

Graco XHD217 XHD RAC SwitchTip, .217

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 15.2
Maximum Fan Width (in): 6
Maximum Fan Width (mm): 152

Maximum Flow Rate (GPM): 0.31
Maximum Flow Rate (L/min): 1.17

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 4
Minimum Fan Width (mm): 102

Orifice Diameter (in): 0.017

$116.50

Wide Rac Tip, Size 1227

GG WR1227

RAC X WIDE RAC TIP, SPRAY, 1227

Graco WR1227 RAC X Wide RAC SwitchTip, 1227

The Reverse-A-Clean (RAC) 1227 RAC X Wide RAC SwitchTip produces a 24 inch fan and has a 0.027 inch orifice. Reverse the SwitchTip to easily clear clogs.

RAC X - Wide RAC
The Wide RAC covers double the area in the same time - increased flow rate ensures the proper mil build
Wide RAC tips are made for high production, new construction applications which may require larger airless sprayers
Superior Tip Design
Locking tab ensures tip stays securely in guard
Snapstip in spray or reverse position
OneSeal tip installs with no tools
Solvent seal available when using extremely hot solvents
Easy to Identify Tip Size
Large raised tip size numbers are always legible - even when covered with paint

Model: RAC X
Series: Wide RAC SwitchTip

For Use With: RAC X HandTite Tip Guard

Maximum Fan Width (cm): 61.0
Maximum Fan Width (in): 24
Maximum Fan Width (mm): 610

Maximum Flow Rate (GPM): 0.77
Maximum Flow Rate (L/min): 2.91

Maximum Working Pressure (bar): 280
Maximum Working Pressure (kPa): 28000
Maximum Working Pressure (psi): 4050

Minimum Fan Width (in): 24
Minimum Fan Width (mm): 610

Orifice Diameter (in): 0.027

Pattern Size (in): 24
Pattern Size (mm): 609.6

$71.50

68:1 Tofw Check-Mate Maxlife, Heated, 55Gal (200L) D200, 16 Gal (60L) Platen Aluminum Platen, Epdm

GG WMC82G2

THERM-O-FLOW SUPPLY UNIT, 68:1HCM, D200-200H, 480V, A

Graco WMC82G2 68:1 TOFw Check-Mate MaxLife, Heated, 55 Gal (200L) D200, 16 Gal (60L) Platen, Aluminum Platen, EPDM, 480V, ADM

Designed with more heat zones, the Therm-O-Flow Bulk Warm Melt Supply Pumps deliver superior temperature control and application flexibility.

Application: Bulk unloader for warm applied materials and temperature conditioning applications.

Designed specifically for sealants or adhesives applications that require a warm applied material for process controls up 158 degree F (70 degree C).
With an heated pump and platen, you can heat up 3 heated hoses and 3 end of hose devices.
Primary unit with ADM can be configured as a tandem system.
Add a second heat zone expansion kit for up to 14 heated hoses and 14 heated end of hose devices on a tandem system for a total of 32 heated zones.
Featuring the Graco Advanced Display Module - an easy-to-use HMI with graphic-based control screens.
Complete integration possibilities through Ethernet/IP, PROFINET, PROFIBUS and DeviceNet or simple integration through discrete I/O.

Model: Therm-O-Flow
Series: Warm Melt

Air Inlet Size (in): 3/4
Air Inlet Thread Gender: Female
Air Inlet Thread Type: NPT

Ambient/Warm Melt/Hot Melt: Warm Melt
Amperage (A): 8

Container Type: Drum
Control Options: Advanced Display Module

Fluid Outlet Size (in): 1
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT

Input Cycle Rate (Hz): 50/60

Lower Type: Check-Mate MaxLife

Material Container Volume (gal): 55
Material Container Volume (l): 200

Maximum Air Inlet Pressure (bar): 10
Maximum Air Inlet Pressure (MPa): 1
Maximum Air Inlet Pressure (psi): 150

Maximum Ambient Temperature ( degree C): 49
Maximum Ambient Temperature ( degree F): 120

Maximum Flow Rate (GPM): 3.2
Maximum Flow Rate (L/min): 12

Maximum Fluid Pressure (bar): 345
Maximum Fluid Pressure (MPa): 34.5
Maximum Fluid Pressure (psi): 5000
Maximum Fluid Temperature ( degree C): 70
Maximum Fluid Temperature ( degree F): 158

Maximum Height (in): 118
Maximum Height (mm): 2997

Maximum Operating Temperature ( degree C): 70
Maximum Operating Temperature ( degree F): 158

Maximum Voltage (V ac): 480

Maximum Working Pressure (bar): 344
Maximum Working Pressure (MPa): 34.4

Minimum Ambient Temperature ( degree C): 0
Minimum Ambient Temperature ( degree F): 32

Minimum Flow Rate (cc/min): 12000

Minimum Height (in): 88
Minimum Height (mm): 2235

Minimum Voltage (V ac): 200

Number of Wipers: Double Ring

Overall Depth (in): 25
Overall Depth (mm): 635

Overall Width (in): 52
Overall Width (mm): 1321

Phase: 1, 3
Plate Material: Aluminum

Power Type: Pneumatic

Pu

$44,160.00

IQ Dispense Valve, Tip-Seal, Ambient, 0.067In (1.7 mm ) Tip, 7.87In(200 mm )Nozzle, Remote Mount Solenoid

GG V25GT200DA

IQ TIP SEAL VALVE, 25, 1.7/T, 200, ADJ/RM, AMB

Graco V25GT200DA iQ Dispense Valve, Tip-Seal, Ambient, 0.067in (1.7mm) Tip, 7.87in (200mm) Nozzle, Remote Mount Solenoid

The iQ Tip Seal Dispense Valve offers high reliability for single component sealant and adhesive dispensing applications.

Maximize dispense time while minimizing maintenance costs and effort
Delivers precise, consistent dispensing with clean starts and stops
Ideal for low to high viscosity materials
Easy repeatable mounting for robotic and automated applications.
200mm nozzle is compatible with 200mm focal length vision systems

Air Inlet Size (in): 1/8
Air Inlet Thread Gender: Female
Air Inlet Thread Type: NPT

Ambient/Warm Melt/Hot Melt: Ambient
Applicator Type: Tip-Seal

Component Type: Single Component

Fluid Inlet Size (in): 1/4
Fluid Inlet Thread Gender: Female
Fluid Inlet Thread Type: NPT

Gun Activation: Automatic

Maximum Air Pressure (bar): 8.3

Maximum Air Pressure (MPa): 0.83
Maximum Air Pressure (psi): 120

Maximum Fluid Pressure (bar): 276
Maximum Fluid Pressure (MPa): 28
Maximum Fluid Pressure (psi): 4000

Mount Location: Remote Mount Solenoid
Nozzle Size (in): 0.067
Nozzle Size (mm): 1.7

Outlet Block Length (in): 7.9
Outlet Block Length (mm): 200

$0.00

Spray Tip, Cylinder (121)

GG XHD121

XHD RAC TIP, SPRAY, CYLINDER, 121

Graco XHD121 XHD RAC SwitchTip, .121

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 10.2
Maximum Fan Width (in): 4
Maximum Fan Width (mm): 102

Maximum Flow Rate (GPM): 0.47
Maximum Flow Rate (L/min): 1.78

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 2
Minimum Fan Width (mm): 51

Orifice Diameter (in): 0.021

$116.50

Tip, Spray Cylinder, (215)

GG XHD215

XHD RAC TIP, SPRAY, CYLINDER, 215

Graco XHD215 XHD RAC SwitchTip, .215

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 15.2
Maximum Fan Width (in): 6
Maximum Fan Width (mm): 152

Maximum Flow Rate (GPM): 0.24
Maximum Flow Rate (L/min): 0.91

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 4
Minimum Fan Width (mm): 102

Orifice Diameter (in): 0.015

$116.50

XHD RAC SwitchTip, .225

GG XHD225

XHD RAC TIP, SPRAY, CYLINDER, 225

Graco XHD225 XHD RAC SwitchTip, .225

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 15.2
Maximum Fan Width (in): 6
Maximum Fan Width (mm): 152

Maximum Flow Rate (GPM): 0.67
Maximum Flow Rate (L/min): 2.54

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 4
Minimum Fan Width (mm): 102

Orifice Diameter (in): 0.025

$116.50

Tip, Spray, Cylinder 219

GG XHD219

XHD RAC TIP, SPRAY, CYLINDER, 219

Graco XHD219 XHD RAC SwitchTip, .219

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 15.2
Maximum Fan Width (in): 6
Maximum Fan Width (mm): 152

Maximum Flow Rate (GPM): 0.38
Maximum Flow Rate (L/min): 1.44

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 4
Minimum Fan Width (mm): 102

Orifice Diameter (in): 0.019

$116.50

XHD RAC Switch Tip, 229

GG XHD229

XHD RAC TIP, SPRAY, CYLINDER, 229

Graco XHD229 XHD RAC SwitchTip, .229

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 15.2
Maximum Fan Width (in): 6
Maximum Fan Width (mm): 152

Maximum Flow Rate (GPM): 0.90
Maximum Flow Rate (L/min): 3.41

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 4
Minimum Fan Width (mm): 102

Orifice Diameter (in): 0.029

$116.50

Tip, RAC Spray

GG XHD221

XHD RAC TIP, SPRAY, CYLINDER, 221

Graco XHD221 XHD RAC SwitchTip, .221

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 15.2
Maximum Fan Width (in): 6
Maximum Fan Width (mm): 152

Maximum Flow Rate (GPM): 0.47
Maximum Flow Rate (L/min): 1.78

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 4
Minimum Fan Width (mm): 102

Orifice Diameter (in): 0.021

$116.50

Tip, Spray. Cylinder 307

GG XHD307

XHD RAC TIP, SPRAY, CYLINDER, 307

Graco XHD307 XHD RAC SwitchTip, .307

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 20.3
Maximum Fan Width (in): 8
Maximum Fan Width (mm): 203

Maximum Flow Rate (GPM): 0.05
Maximum Flow Rate (L/min): 0.19

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 6
Minimum Fan Width (mm): 152

Orifice Diameter (in): 0.007

$116.50

Tip, Spray, Cylinder (239)

GG XHD239

XHD RAC TIP, SPRAY, CYLINDER, 239

Graco XHD239 XHD RAC SwitchTip, .239

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 15.2
Maximum Fan Width (in): 6
Maximum Fan Width (mm): 152

Maximum Flow Rate (GPM): 1.63
Maximum Flow Rate (L/min): 6.17

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 4
Minimum Fan Width (mm): 102

Orifice Diameter (in): 0.039

$116.50

Spray Tip, Cylinder

GG XHD311

XHD RAC TIP, SPRAY, CYLINDER, 311

Graco XHD311 XHD RAC SwitchTip, .311

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 20.3
Maximum Fan Width (in): 8
Maximum Fan Width (mm): 203

Maximum Flow Rate (GPM): 0.12
Maximum Flow Rate (L/min): 0.45

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 6
Minimum Fan Width (mm): 152

Orifice Diameter (in): 0.011

$116.50

Tip, Spray, Cylinder (231)

GG XHD231

XHD RAC TIP, SPRAY, CYLINDER, 231

Graco XHD231 XHD RAC SwitchTip, .231

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 15.2
Maximum Fan Width (in): 6
Maximum Fan Width (mm): 152

Maximum Flow Rate (GPM): 1.03
Maximum Flow Rate (L/min): 3.90

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 4
Minimum Fan Width (mm): 102

Orifice Diameter (in): 0.031

$116.50

Tip, Spray, Cylinder (235)

GG XHD235

XHD RAC TIP, SPRAY, CYLINDER, 235

Graco XHD235 XHD RAC SwitchTip, .235

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 15.2
Maximum Fan Width (in): 6
Maximum Fan Width (mm): 152

Maximum Flow Rate (GPM): 1.31
Maximum Flow Rate (L/min): 4.96

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 4
Minimum Fan Width (mm): 102

Orifice Diameter (in): 0.035

$116.50

Spray Tip, Cylinder

GG XHD313

XHD RAC TIP, SPRAY, CYLINDER, 313

Graco XHD313 XHD RAC SwitchTip, .313

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 20.3
Maximum Fan Width (in): 8
Maximum Fan Width (mm): 203

Maximum Flow Rate (GPM): 0.18
Maximum Flow Rate (L/min): 0.68

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 6
Minimum Fan Width (mm): 152

Orifice Diameter (in): 0.013

$116.50

Tip, RAC Spray

GG XHD319

XHD RAC TIP, SPRAY, CYLINDER, 319

Graco XHD319 XHD RAC SwitchTip, .319

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 20.3
Maximum Fan Width (in): 8
Maximum Fan Width (mm): 203

Maximum Flow Rate (GPM): 0.38
Maximum Flow Rate (L/min): 1.44

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 6
Minimum Fan Width (mm): 152

Orifice Diameter (in): 0.019

$116.50

Tip, Spray, Cylinder, 309

GG XHD309

XHD RAC TIP, SPRAY, CYLINDER, 309

Graco XHD309 XHD RAC SwitchTip, .309

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 20.3
Maximum Fan Width (in): 8
Maximum Fan Width (mm): 203

Maximum Flow Rate (GPM): 0.09
Maximum Flow Rate (L/min): 0.34

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 6
Minimum Fan Width (mm): 152

Orifice Diameter (in): 0.009

$116.50

Tip, Spray Cylinder (315)

GG XHD315

XHD RAC TIP, SPRAY, CYLINDER, 315

Graco XHD315 XHD RAC SwitchTip, .315

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 20.3
Maximum Fan Width (in): 8
Maximum Fan Width (mm): 203

Maximum Flow Rate (GPM): 0.24
Maximum Flow Rate (L/min): 0.91

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 6
Minimum Fan Width (mm): 152

Orifice Diameter (in): 0.015

$116.50

Tip, Spray, Cylinder (333)

GG XHD333

XHD RAC TIP, SPRAY, CYLINDER, 333

Graco XHD333 XHD RAC SwitchTip, .333

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 20.3
Maximum Fan Width (in): 8
Maximum Fan Width (mm): 203

Maximum Flow Rate (GPM): 1.17
Maximum Flow Rate (L/min): 4.43

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 6
Minimum Fan Width (mm): 152

Orifice Diameter (in): 0.033

$116.50

Tip, Spray Cylinder (317)

GG XHD317

XHD RAC TIP, SPRAY, CYLINDER, 317

Graco XHD317 XHD RAC SwitchTip, .317

With its Reverse-A-Clean (RAC) Tip, it's easy to clear clogs. The Switch Tip design lets you change tip sizes in seconds - without removing the tip guard and housing.

Application: High-Pressure Airless Spray Tip for XTR and XHF Guns. Designed for spraying high-solids coatings at high pressures.

Saves time - no screwdriver required, change tip sizes in seconds
For heavy-duty applications up to 7250 psi (500 bar)
Recommended for use with Xtreme Sprayers and XTR Guns

Model: XHD RAC
Series: SwitchTip

Compatible Material: Solvent borne Paints, Water-Based Paint

For Use With: Xtreme Sprayers, XTR Airless Spray Guns

Maximum Fan Width (cm): 20.3
Maximum Fan Width (in): 8
Maximum Fan Width (mm): 203

Maximum Flow Rate (GPM): 0.31
Maximum Flow Rate (L/min): 1.17

Maximum Working Pressure (bar): 500
Maximum Working Pressure (kPa): 50000
Maximum Working Pressure (psi): 7250

Minimum Fan Width (in): 6
Minimum Fan Width (mm): 152

Orifice Diameter (in): 0.017

$116.50

Air Motor Valve Assembly, HLS

GG NXT109

Air Motor Valve Assembly, HLS

$1,795.00

Valve Assy, Motor, DataTrac

GG NXT108

VALVE, ASSY, MOTOR, DATATRAK

$2,550.00

Kit Exh Manifold De-Ice

GG NXT110

Kit Exh Manifold De-Ice

$449.00

Kit, Repair, Valve Soft Seal

GG NXT135

Kit, Repair, Valve Soft Seal

$177.50

Kit, De-Ice Control, 5 Pack

GG NXT112

Kit, De-Ice Control, 5 Pack

$0.00

Kit, Repair Soft Seal Nxt 2200

GG NXT200

KIT, REPAIR SOFT SEAL NXT 2200

$177.50

Kit, Repair, Soft Seal Nxt 3400

GG NXT300

KIT, REPAIR, SOFT SEAL NXT 3400

$234.00

Kit, Repair, Cylinder NXT 2200

GG NXT204

Kit, Repair, Cylinder NXT 2200

$536.00

Kit, Repair, Valve Wear Parts

GG NXT144

Kit, Repair, Valve Wear Parts

$428.00

Base, End, Cap, NXT 3400

GG NXT302

Base, End, Cap, NXT 3400

$595.00

Kit, Repair, Cylinder Nxt 3400

GG NXT304

Kit, Repair, Cylinder Nxt 3400

$601.00

Kit, Cnvrsn, Datatrak, 3400

GG NXT306

Kit, Cnvrsn, Datatrak, 3400

$2,180.00

Kit, Repair, Soft Seal Nxt 6500

GG NXT600

KIT, REPAIR, SOFT SEAL NXT 6500

Graco NXT600 NXT Model 6500 Air Motor Repair Kit

$234.00

Kit, Cvsrn, Remote Datatrak

GG NXT406

Kit, Cvsrn, Remote Datatrak

$418.00

Kit, Repair, Datatrak Module

GG NXT402

Kit, Repair, Datatrak Module

$1,025.00

Kit, Repair, Fuse, Datatrak

GG NXT413

Kit, Repair, Fuse, Datatrak

$58.25

Kit, Repair, Cylinder Nxt 6500

GG NXT604

Kit, Repair, Cylinder Nxt 6500

$675.00

Kit, Repair Reed Switch

GG NXT404

Kit, Repair Reed Switch

$131.00

Base, End Cap, Nxt 6500

GG NXT602

Base, End Cap, Nxt 6500

$670.00

DURA-FLO NXT 2-BALL PISTON PUMP, 6:1, DE-ICING EXHAUST MOTOR, CS, UHM WITH LEATHER PACKINGS

GG P06DCK

DURA-FLO PUMP, 3400/1000

Graco P06DCK Dura-Flo NXT 2-Ball Piston Pump, 6:1, De-Icing Exhaust Motor, CS, UHM with Leather Packings

Graco's Dura-Flo pumps with NXT technology provide uniform and easy to control delivery. Ideal for supply applications, these durable pumps feature an NXT motor and can now achieve an even higher range of pressures without compromising flow.

Positive displacement, 2 ball piston design provides uniform and easily controlled delivery
High pump pressure and flow performance to handle a broad range of paints and coatings
Improved serviceability with fewer parts, faster repairs and lower ownership cost

Model: Dura-Flo
Series: 2-Ball

Application: Supply

Compatible Material: Solvent borne, High Solids, Xirallic, CARC, Metallics, Stains, Varnish

Fluid Outlet Size (in): 1-1/2
Fluid Outlet Size (mm): 38.1
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT
Fluid Section Type: 2-Ball

Includes: Carbon Steel Pump, De-Icing Exhaust Motor, UHMW / Leather Packings

Material: Carbon Steel

Maximum Air Inlet Pressure (bar): 6.9
Maximum Air Inlet Pressure (kPa): 690
Maximum Air Inlet Pressure (psi): 100

Maximum Continuous Cycle Rate (CPM): 60

Maximum Flow Rate (GPM): 17.4
Maximum Flow Rate (L/min): 65.87

Maximum Operating Temperature ( degree C): 66
Maximum Operating Temperature ( degree F): 150

Maximum Working Pressure (bar): 43
Maximum Working Pressure (kPa): 4300
Maximum Working Pressure (MPa): 4.3
Maximum Working Pressure (psi): 620

Motor Type: De-Icing NXT

Mount Type: Wall or Stand Mount

Portable: Non-Portable

Pump Ratio: 6:1

$12,950.00

Kit, Repair, Piston, Nxt 6500

GG NXT601

Kit, Repair, Piston, Nxt 6500

$727.00

Muffler Nxt 6500

GG NXT603

Muffler Nxt 6500

$898.00

Dura-Flo Pump, 3400/1000

GG P06DSG

DURA-FLO PUMP, 3400/1000

Graco P06DSG Dura-Flo NXT 2-Ball Piston Pump, 6:1, De-Icing Exhaust Motor, SST, PTFE/PTFE Packings

Graco's Dura-Flo pumps with NXT technology provide uniform and easy to control delivery. Ideal for supply applications, these durable pumps feature an NXT motor and can now achieve an even higher range of pressures without compromising flow.

Positive displacement, 2 ball piston design provides uniform and easily controlled delivery
High pump pressure and flow performance to handle a broad range of paints and coatings
Improved serviceability with fewer parts, faster repairs and lower ownership cost

Model: Dura-Flo
Series: 2-Ball

Application: Supply

Compatible Material: Solvent borne, High Solids, Xirallic, CARC, Metallics, Stains, Varnish

Fluid Outlet Size (in): 1
Fluid Outlet Size (mm): 25.4
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT
Fluid Section Type: 2-Ball

Includes: Stainless Steel Pump, De-Icing Exhaust Motor, PTFE / PTFE Packings

Material: Stainless Steel

Maximum Air Inlet Pressure (bar): 6.9
Maximum Air Inlet Pressure (kPa): 690
Maximum Air Inlet Pressure (psi): 100

Maximum Continuous Cycle Rate (CPM): 60

Maximum Flow Rate (GPM): 17.4
Maximum Flow Rate (L/min): 65.87

Maximum Operating Temperature ( degree C): 66
Maximum Operating Temperature ( degree F): 150

Maximum Working Pressure (bar): 43
Maximum Working Pressure (kPa): 4300
Maximum Working Pressure (MPa): 4.3
Maximum Working Pressure (psi): 620

Motor Type: De-Icing NXT

Mount Type: Wall or Stand Mount

Portable: Non-Portable

Pump Ratio: 6:1

$12,820.00

Dura-Flo Pump, 3400/1000

GG P06ECK

DURA-FLO PUMP, 3400/1000

Graco P06ECK Dura-Flo NXT 2-Ball Piston Pump, 6:1, De-Icing Exhaust Motor, DataTrak, CS, UHM with Leather Packings

Graco's Dura-Flo pumps with NXT technology provide uniform and easy to control delivery. Ideal for supply applications, these durable pumps feature an NXT motor and can now achieve an even higher range of pressures without compromising flow.

Positive displacement, 2 ball piston design provides uniform and easily controlled delivery
High pump pressure and flow performance to handle a broad range of paints and coatings
Improved serviceability with fewer parts, faster repairs and lower ownership cost

Model: Dura-Flo
Series: 2-Ball

Application: Supply

Compatible Material: Solvent borne, High Solids, Xirallic, CARC, Metallics, Stains, Varnish

Fluid Outlet Size (in): 1-1/2
Fluid Outlet Size (mm): 38.1
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT
Fluid Section Type: 2-Ball

Includes: Carbon Steel Pump, De-Icing Exhaust Motor, DataTrak Monitor, UHMW / Leather Packings

Material: Carbon Steel

Maximum Air Inlet Pressure (bar): 6.9
Maximum Air Inlet Pressure (kPa): 690
Maximum Air Inlet Pressure (psi): 100

Maximum Continuous Cycle Rate (CPM): 60

Maximum Flow Rate (GPM): 17.4
Maximum Flow Rate (L/min): 65.87

Maximum Operating Temperature ( degree C): 66
Maximum Operating Temperature ( degree F): 150

Maximum Working Pressure (bar): 43
Maximum Working Pressure (kPa): 4300
Maximum Working Pressure (MPa): 4.3
Maximum Working Pressure (psi): 620

Motor Type: De-Icing NXT with DataTrak

Mount Type: Wall or Stand Mount

Portable: Non-Portable

Pump Ratio: 6:1

$14,340.00

Dura-Flo NXT 2-Ball Piston Pump, 10:1, De-Icing Exhaust Motor, DataTrak, CS, UHM W/Leather Packings

GG P10ECK

Dura-Flo NXT 2-Ball Piston Pump, 10:1, De-Icing Exhaust Motor, DataTrak, CS, UHM W/Leather Packings

$0.00

Dura-Flo Pump, 3400/1000

GG P06LCK

DURA-FLO PUMP, 3400/1000

Graco P06LCK Dura-Flo NXT 2-Ball Piston Pump, 6:1, Low Noise Exhaust Motor, CS, UHM with Leather Packings

Graco's Dura-Flo pumps with NXT technology provide uniform and easy to control delivery. Ideal for supply applications, these durable pumps feature an NXT motor and can now achieve an even higher range of pressures without compromising flow.

Positive displacement, 2 ball piston design provides uniform and easily controlled delivery
High pump pressure and flow performance to handle a broad range of paints and coatings
Improved serviceability with fewer parts, faster repairs and lower ownership cost

Model: Dura-Flo
Series: 2-Ball

Application: Supply

Compatible Material: Solvent borne, High Solids, Xirallic, CARC, Metallics, Stains, Varnish

Fluid Outlet Size (in): 1-1/2
Fluid Outlet Size (mm): 38.1
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT
Fluid Section Type: 2-Ball

Includes: Carbon Steel Pump, Low Noise Exhaust Motor, UHMW / Leather Packings

Material: Carbon Steel

Maximum Air Inlet Pressure (bar): 6.9
Maximum Air Inlet Pressure (kPa): 690
Maximum Air Inlet Pressure (psi): 100

Maximum Continuous Cycle Rate (CPM): 60

Maximum Flow Rate (GPM): 17.4
Maximum Flow Rate (L/min): 65.87

Maximum Operating Temperature ( degree C): 66
Maximum Operating Temperature ( degree F): 150

Maximum Working Pressure (bar): 43
Maximum Working Pressure (kPa): 4300
Maximum Working Pressure (MPa): 4.3
Maximum Working Pressure (psi): 620

Motor Type: Low Noise NXT

Mount Type: Wall or Stand Mount

Portable: Non-Portable

Pump Ratio: 6:1

$0.00

QUANTM I120, 2 Inch Flange, Poly Electric Diaphragm Pump, 200-240 Volt, AL Center, BN Seat, Ball, And Diaphragm

GG TE120-0036

QUANTM PUMP, QTE-PPFC1BNBNBN-P200

Graco TE120-0036 QUANTM i120, 2" Flange, Polypropylene Electric Diaphragm Pump, 200-240 V, AL Center, BN Seat, BN Ball, BN Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: Designed with a chemical-resistant polypropylene fluid section that provides high corrosion resistance, this groundbreaking electric pump is built to efficiently handle fluid transfer applications involving most chemicals and detergents, sump evacuation applications, as well as applications involving high and low pH materials. With up to 8x more continuous torque at low speeds than conventional motors, this powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework.

Revolutionary Design
- Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
- Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
- Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
- Quiet operation reduces plant noise and improves employee safety and health
- Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor
- Powder-coated aluminum electric drive
- 240 VAC 3Ph motor with 15 ft cord and NEMA L15-20 plug
- Non-hazardous
Materials of Construction
- Polypropylene fluid section with end flange
- Internal components include Buna-N seat, Buna-N ball, Buna-N diaphragm and Buna-N manifold o-ring

Model: QUANTM
Series: i120

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: Buna-N

Center Section Material: Aluminum

Connection Type: Flange

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: Buna-N

Fluid Inlet Size (in): 2
Fluid Inlet Size (mm): 51
Fluid Inlet Thread Gender: Flange
Fluid Inlet Thread Type: Flange

Fluid Outlet Size (in): 2
Fluid Outlet Size (mm): 50.8
Fluid Outlet Thread Gender: Flange
Fluid Outlet Thread Type: Flange
Fluid Section: Polypropylene, End Flange
Fluid Section Material: Polypropylene

Hazardous Location Approval: None

Manifold Configuration: End Flange
Manifold O-Ring Material: Buna-N

Maximum Ambient Temperature ( d

$8,710.00

QUANTM i120, 2in NPT, Alum Elec dia pump, FluxCore drive, 240 V, AL centre, SS seat, SD ball, Flouroelastomer Viton diaphragms, 480V three phase AC power supply

GG TE120-1207

QUANTM PUMP, QTE-SSFE7SASDPSPTS100

Graco TE120-1207 QUANTM i120, 2" NPT, Stainless Steel Electric Diaphragm Pump, 380 - 480 VAC 3Ph, FEP AL Center, SA Seat, SD Ball, PS Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: The stainless-steel fluid section is designed to provide a high level of abrasion and corrosion resistance. With up to 8x more continuous torque at low speeds than conventional motors, this electric pump is an energy-saving workhorse that also delivers lower lifetime costs than less efficient pump technologies and is ideal for applications involving materials that are highly abrasive, paints, solvents or heated materials. This additional resilience means less downtime, which in turn provides a new opportunity to improve your bottom line. This powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework.

Revolutionary Design
- Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
- Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
- Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
- Quiet operation reduces plant noise and improves employee safety and health
- Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor
- FEP Coated Aluminum electric drive
- 380-480 VAC 3Ph motor with 15 ft flying leads
- Non-hazardous
Materials of Construction
- 316 Stainless Steel fluid section with NPT End Port
- Internal components include 17-4 Stainless Steel seats, 440-C Stainless Steel balls, and PTFE/Santoprene 2-Piece diaphragms

Model: QUANTM
Series: i120

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: 440-C Stainless Steel

Center Section Material: FEP Coated Aluminum

Connection Type: NPT

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: PTFE/Santoprene 2-Piece

Fluid Inlet Size (in): 2
Fluid Inlet Size (mm): 50.8
Fluid Inlet Thread Gender: Female
Fluid Inlet Thread Type: NPT

Fluid Outlet Size (in): 2
Fluid Outlet Size (mm): 50.8
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT
Fluid Section: 316 Stainless Steel, End Port, NPT
Fluid Section Material: 316 Stainless

$11,970.00

QUANTM i120, 2" Flange, polypro Elec dia pump, FluxCore drive, 240 V, AL hub, SP seat, SP ball, SPdia

GG TE120-0023

QUANTM PUMP, QTE-PPFC1SPSPSPPTP200

Graco TE120-0023 QUANTM i120, 2" Flange, Polypropylene Electric Diaphragm Pump, 200-240 V, AL Center, SP Seat, SP Ball, SP Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: Designed with a chemical-resistant polypropylene fluid section that provides high corrosion resistance, this groundbreaking electric pump is built to efficiently handle fluid transfer applications involving most chemicals and detergents, sump evacuation applications, as well as applications involving high and low pH materials. With up to 8x more continuous torque at low speeds than conventional motors, this powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework.

Revolutionary Design
Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
Quiet operation reduces plant noise and improves employee safety and health
Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor Powder-coated aluminum electric drive240 VAC 3 phase motor with 15 ft cord and NEMA L15-20 plugNon-hazardous
Materials of Construction Polypropylene fluid section with end flangeInternal components include Santoprene seat, Santoprene ball, Santoprene diaphragm and PTFE manifold o-ring

Model: QUANTM
Series: i120

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: Santoprene

Center Section Material: Aluminum

Connection Type: Flange

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: Santoprene

Fluid Inlet Size (in): 2
Fluid Inlet Size (mm): 51
Fluid Inlet Thread Gender: Flange
Fluid Inlet Thread Type: Flange

Fluid Outlet Size (in): 2
Fluid Outlet Size (mm): 50.8
Fluid Outlet Thread Gender: Flange
Fluid Outlet Thread Type: Flange
Fluid Section: Polypropylene, End Flange
Fluid Section Material: Polypropylene

Hazardous Location Approval: None

Manifold Configuration: End Flange
Manifold O-Ring Material: PTFE

Maximum Ambi

$8,880.00

QUANTM i30, 1" NPT, SS Elec Dia Pump, FluxCore drive, 120 VAC, AL Centre, SS seat, PT ball, PS dia

GG TE30-0002

QUANTM PUMP, QTC-SSFC5SAPTPSPTS100

Graco TE30-0002 QUANTM i30, 1" NPT, Stainless Steel Electric Diaphragm Pump, 120 VAC 1Ph, AL Center, SS Seat, PT Ball, PS Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: The stainless-steel fluid section is designed to provide a high level of abrasion and corrosion resistance. With up to 8x more continuous torque at low speeds than conventional motors, this electric pump is an energy-saving workhorse that also delivers lower lifetime costs than less efficient pump technologies and is ideal for applications involving materials that are highly abrasive, paints, solvents or heated materials. This additional resilience means less downtime, which in turn provides a new opportunity to improve your bottom line. This powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework.

Revolutionary Design
- Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
- Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
- Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
- Quiet operation reduces plant noise and improves employee safety and health
- Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor
- Powder-coated aluminum electric drive
- 120 VAC 1Ph motor with 15 ft cord and NEMA 5-15 plug
- Non-hazardous
Materials of Construction
- Stainless steel fluid section with NPT end port
- Internal components include 316 stainless steel seat, PTFE ball, PTFE/Santoprene 2-piece diaphragm and PTFE manifold o-ring

Model: QUANTM
Series: i30

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: PTFE

Center Section Material: Aluminum

Connection Type: NPT

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: PTFE/Santoprene 2-Piece

Fluid Inlet Size (in): 1
Fluid Inlet Size (mm): 25.4
Fluid Inlet Thread Gender: Female
Fluid Inlet Thread Type: NPT

Fluid Outlet Size (in): 1
Fluid Outlet Size (mm): 25.4
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT
Fluid Section: Stainless Steel, End Port, NPT
Fluid Section Material: Stainless Steel

Hazardous Locatio

$5,200.00

QUANTM i30, 1" NPT, Alum Elec dia pump, FluxCore drive, 120 VAC, AL centre, SS seat, SS ball, PS dia

GG TE30-0006

QUANTM QUANTM PUMP, QTC-ALFC5SSSSPSPTA100

Graco TE30-0006 QUANTM i30, 1" NPT, Aluminum Electric Diaphragm Pump, 120 VAC 1Ph, AL Center, SS Seat, SS Ball, PS Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: The all-aluminum fluid section is specifically designed to be abrasion-resistant while also providing mild corrosion resistance. With up to 8x more continuous torque at low speeds than conventional motors, this general-purpose electric pump is an energy-saving workhorse that is ideal for sump evacuation applications as well as applications involving the evacuation of petroleum products (new and waste oils) and evacuation of solvents. This powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework. Not for use with halogenated hydrocarbons.

Revolutionary Design
Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
Quiet operation reduces plant noise and improves employee safety and health
Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor Powder-coated aluminum electric drive 120 VAC motor with 15 ft cord and NEMA 5-15 plugNon-hazardous
Materials of Construction Aluminum fluid section with NPT end portInternal components include 316 stainless steel seat, 316 stainless steel ball, PTFE/Santoprene 2-piece diaphragm and PTFE manifold o-ring

Model: QUANTM
Series: i30

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: 316 Stainless Steel

Center Section Material: Aluminum

Connection Type: NPT

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: PTFE/Santoprene 2-Piece

Fluid Inlet Size (in): 1
Fluid Inlet Size (mm): 25.4
Fluid Inlet Thread Gender: Female
Fluid Inlet Thread Type: NPT

Fluid Outlet Size (in): 1
Fluid Outlet Size (mm): 25.4
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT
Fluid Section: Aluminum, End Port, NPT
Fluid Section Material: Aluminum

Hazardous Location Approval: None

Manifold Configura

$3,740.00

QUANTM i120, 2" NPT, SS Elec dia pump, FluxCore drive, 240 V, AL centre, SS seat, PT ball, PO dia

GG TE120-0173

QUANTM PUMP, QTE-SSFC3SSPTPOPTS100

Graco TE120-0173 QUANTM i120, 2" NPT, Stainless Steel Electric Diaphragm Pump, 200-240 V, AL Center, SS Seat, PT Ball, PO Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: The stainless-steel fluid section is designed to provide a high level of abrasion and corrosion resistance. With up to 8x more continuous torque at low speeds than conventional motors, this electric pump is an energy-saving workhorse that also delivers lower lifetime costs than less efficient pump technologies and is ideal for applications involving materials that are highly abrasive, paints, solvents or heated materials. This additional resilience means less downtime, which in turn provides a new opportunity to improve your bottom line. This powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework.

Revolutionary Design
Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
Quiet operation reduces plant noise and improves employee safety and health
Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor Powder-coated aluminum electric drive240 VAC 3 phase motor with 15 ft flying leadsCID1 Groups C,D,T4 Zone 1 AEx d b IIB T4 Gb hazardous location approval
Materials of Construction 316 stainless steel fluid section with NPT end portInternal components include 316 stainless steel seat, PTFE ball, PTFE Overmold diaphragm and PTFE manifold o-ring

Model: QUANTM
Series: i120

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: PTFE

Center Section Material: Aluminum

Connection Type: NPT

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: PTFE Overmold

Fluid Inlet Size (in): 2
Fluid Inlet Size (mm): 51
Fluid Inlet Thread Gender: Female
Fluid Inlet Thread Type: NPT

Fluid Outlet Size (in): 2
Fluid Outlet Size (mm): 50.8
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT
Fluid Section: 316 Stainless Steel, End Port, NPT
Fluid Section Material: 316 Stainless St

$13,210.00

QUANTM i30, 1" NPT, Alum Elec dia pump, FluxCore drive, 120 VAC, AL centre, SS seat, SS ball, PO dia

GG TE30-0039

QUANTM QUANTM PUMP, QTC-ALFC5SSSSPOPTA100

Graco TE30-0039 QUANTM i30, 1" NPT, Aluminum Electric Diaphragm Pump, 120 VAC 1Ph, AL Center, SS Seat, SS Ball, PO Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: The all-aluminum fluid section is specifically designed to be abrasion-resistant while also providing mild corrosion resistance. With up to 8x more continuous torque at low speeds than conventional motors, this general-purpose electric pump is an energy-saving workhorse that is ideal for sump evacuation applications as well as applications involving the evacuation of petroleum products (new and waste oils) and evacuation of solvents. This powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework. Not for use with halogenated hydrocarbons.

Revolutionary Design
Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
Quiet operation reduces plant noise and improves employee safety and health
Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor Powder-coated aluminum electric drive 120 VAC motor with 15 ft cord and NEMA 5-15 plugNon-hazardous
Materials of Construction Aluminum fluid section with NPT end portInternal components include 316 stainless steel seat, 316 stainless steel ball, PTFE overmold diaphragm and PTFE manifold o-ring

Model: QUANTM
Series: i30

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: 316 Stainless Steel

Center Section Material: Aluminum

Connection Type: NPT

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: PTFE Overmold

Fluid Inlet Size (in): 1
Fluid Inlet Size (mm): 25.4
Fluid Inlet Thread Gender: Female
Fluid Inlet Thread Type: NPT

Fluid Outlet Size (in): 1
Fluid Outlet Size (mm): 25.4
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT
Fluid Section: Aluminum, End Port, NPT
Fluid Section Material: Aluminum

Hazardous Location Approval: None

Manifold Configuration: End Port

$4,070.00

QUANTM i30, 1" BSPT, Alum Elec dia Pump, 120 VAC 1Ph, AL Center, AC Seat, AC Ball, PS dia

GG TE30-0015

QUANTM QUANTM PUMP, QTC-ALFC5ACACPSPTA200

Graco TE30-0015 QUANTM i30, 1" BSPT, Aluminum Electric Diaphragm Pump, 120 VAC 1Ph, AL Center, AC Seat, AC Ball, PS Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: The all-aluminum fluid section is specifically designed to be abrasion-resistant while also providing mild corrosion resistance. With up to 8x more continuous torque at low speeds than conventional motors, this general-purpose electric pump is an energy-saving workhorse that is ideal for sump evacuation applications as well as applications involving the evacuation of petroleum products (new and waste oils) and evacuation of solvents. This powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework. Not for use with halogenated hydrocarbons.

Revolutionary Design
Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
Quiet operation reduces plant noise and improves employee safety and health
Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor Powder-coated aluminum electric drive 120 VAC motor with 15 ft cord and NEMA 5-15 plugNon-hazardous
Materials of Construction Aluminum fluid section with BSPT end portInternal components include acetal seat, acetal ball, PTFE/Santoprene 2-piece diaphragm and PTFE manifold o-ring

Model: QUANTM
Series: i30

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: Acetal

Center Section Material: Aluminum

Connection Type: BSPT

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: PTFE/Santoprene 2-Piece

Fluid Inlet Size (in): 1
Fluid Inlet Size (mm): 25.4
Fluid Inlet Thread Gender: Female
Fluid Inlet Thread Type: BSPT

Fluid Outlet Size (in): 1
Fluid Outlet Size (mm): 25.4
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: BSPT
Fluid Section: Aluminum, End Port, BSPT
Fluid Section Material: Aluminum

Hazardous Location Approval: None

Manifold Configuration: End Port
Man

$3,460.00

QUANTM i30, 1" NPT, Alum Elec dia pump, FluxCore drive, 120 VAC, AL centre, AL seat, BN ball, BN dia

GG TE30-0048

QUANTM QUANTM PUMP, QTC-ALFC5ALBNBNPTA100

Graco TE30-0048 QUANTM i30, 1" NPT, Aluminum Electric Diaphragm Pump, 120 VAC 1Ph, AL Center, AL Seat, BN Ball, BN Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: The all-aluminum fluid section is specifically designed to be abrasion-resistant while also providing mild corrosion resistance. With up to 8x more continuous torque at low speeds than conventional motors, this general-purpose electric pump is an energy-saving workhorse that is ideal for sump evacuation applications as well as applications involving the evacuation of petroleum products (new and waste oils) and evacuation of solvents. This powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework. Not for use with halogenated hydrocarbons.

Revolutionary Design
Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
Quiet operation reduces plant noise and improves employee safety and health
Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor Powder-coated aluminum electric drive 120 VAC motor with 15 ft cord and NEMA 5-15 plugNon-hazardous
Materials of Construction Aluminum fluid section with NPT end portInternal components include Aluminum seat, Buna-N ball, Buna-N diaphragm and PTFE manifold o-ring

Model: QUANTM
Series: i30

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: Buna-N

Center Section Material: Aluminum

Connection Type: NPT

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: Buna-N

Fluid Inlet Size (in): 1
Fluid Inlet Size (mm): 25.4
Fluid Inlet Thread Gender: Female
Fluid Inlet Thread Type: NPT

Fluid Outlet Size (in): 1
Fluid Outlet Size (mm): 25.4
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT
Fluid Section: Aluminum, End Port, NPT
Fluid Section Material: Aluminum

Hazardous Location Approval: None

Manifold Configuration: End Port
Manifold O-Ring Material: PTFE

$3,860.00

QUANTM i30, 1in Flange, polypro Elec dia pump, FluxCore drive, 120V, AL hub, SP seat, SP ball, SP dia

GG TE30-0115

QUANTM QUANTM PUMP, QTC-PPFC5SPSPSPPTP200

Graco TE30-0115 QUANTM i30, 1" Flange, Polypropylene Electric Diaphragm Pump, 120 VAC 1Ph, AL Center, SP Seat, SP Ball, SP Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: Designed with a chemical-resistant polypropylene fluid section that provides high corrosion resistance, this groundbreaking electric pump is built to efficiently handle fluid transfer applications involving most chemicals and detergents, sump evacuation applications, as well as applications involving high and low pH materials. With up to 8x more continuous torque at low speeds than conventional motors, this powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework.

Revolutionary Design
Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
Quiet operation reduces plant noise and improves employee safety and health
Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor Powder-coated aluminum electric drive 120 VAC motor with 15 ft cord and NEMA 5-15 plugNon-hazardous
Materials of Construction Polypropylene fluid section with end flangeInternal components include Santoprene seat, Santoprene ball, Santoprene diaphragm and PTFE manifold o-ring

Model: QUANTM
Series: i30

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: Santoprene

Center Section Material: Aluminum

Connection Type: Flange

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: Santoprene

Fluid Inlet Size (in): 1
Fluid Inlet Size (mm): 25.4
Fluid Inlet Thread Gender: Flange
Fluid Inlet Thread Type: Flange

Fluid Outlet Size (in): 1
Fluid Outlet Size (mm): 25.4
Fluid Outlet Thread Gender: Flange
Fluid Outlet Thread Type: Flange
Fluid Section: Polypropylene, End Flange
Fluid Section Material: Polypropylene

Hazardous Location Approval: None

Manifold Configuration: End Flange
Manifold O-Ring Material: PTFE

Maximum Ambien

$3,740.00

QUANTM i30, 1" Flange, polypro Elec dia pump, FluxCore drive, 120V, AL hub, PP seat, PT ball, PO dia

GG TE30-0120

QUANTM QUANTM PUMP, QTC-PPFC5PPPTPOPTP200

Graco TE30-0120 QUANTM i30, 1" Flange, Polypropylene Electric Diaphragm Pump, 120 VAC 1Ph, AL Center, PP Seat, PT Ball, PO Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: Designed with a chemical-resistant polypropylene fluid section that provides high corrosion resistance, this groundbreaking electric pump is built to efficiently handle fluid transfer applications involving most chemicals and detergents, sump evacuation applications, as well as applications involving high and low pH materials. With up to 8x more continuous torque at low speeds than conventional motors, this powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework.

Revolutionary Design
Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
Quiet operation reduces plant noise and improves employee safety and health
Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor Powder-coated aluminum electric drive 120 VAC motor with 15 ft cord and NEMA 5-15 plugNon-hazardous
Materials of Construction Polypropylene fluid section with end flangeInternal components include Polypropylene seat, PTFE ball, PTFE overmold diaphragm and PTFE manifold o-ring

Model: QUANTM
Series: i30

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: PTFE

Center Section Material: Aluminum

Connection Type: Flange

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: PTFE Overmold

Fluid Inlet Size (in): 1
Fluid Inlet Size (mm): 25.4
Fluid Inlet Thread Gender: Flange
Fluid Inlet Thread Type: Flange

Fluid Outlet Size (in): 1
Fluid Outlet Size (mm): 25.4
Fluid Outlet Thread Gender: Flange
Fluid Outlet Thread Type: Flange
Fluid Section: Polypropylene, End Flange
Fluid Section Material: Polypropylene

Hazardous Location Approval: None

Manifold Configuration: End Flange
Manifold O-Ring Material: PTFE

Maximum Ambient T

$4,040.00

QUANTM i30, 1" NPT, SS Elec dia pump, FluxCore drive, 120 VAC, AL centre, SS seat, PT ball, PS dia

GG TE30-0314

QUANTM PUMP, QTC-SSFC6SSPTPSPTS100

Graco TE30-0314 QUANTM i30, 1" NPT, Stainless Steel Electric Diaphragm Pump, 120 VAC 1Ph, AL Center, SS Seat, PT Ball, PS Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: The stainless-steel fluid section is designed to provide a high level of abrasion and corrosion resistance. With up to 8x more continuous torque at low speeds than conventional motors, this electric pump is an energy-saving workhorse that also delivers lower lifetime costs than less efficient pump technologies and is ideal for applications involving materials that are highly abrasive, paints, solvents or heated materials. This additional resilience means less downtime, which in turn provides a new opportunity to improve your bottom line. This powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework.

Revolutionary Design
Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
Quiet operation reduces plant noise and improves employee safety and health
Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor Powder-coated aluminum electric drive 120 VAC motor with 15 ft flying leadsCID1 Groups C,D,T4 Zone 1 AEx d b IIB T4 Gb hazardous location approval
Materials of Construction Stainless steel fluid section with NPT end portInternal components include 316 stainless steel seat, PTFE ball, PTFE/Santoprene 2-piece diaphragm and PTFE manifold o-ring

Model: QUANTM
Series: i30

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: PTFE

Center Section Material: Aluminum

Connection Type: NPT

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: PTFE/Santoprene 2-Piece

Fluid Inlet Size (in): 1
Fluid Inlet Size (mm): 25.4
Fluid Inlet Thread Gender: Female
Fluid Inlet Thread Type: NPT

Fluid Outlet Size (in): 1
Fluid Outlet Size (mm): 25.4
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT
Fluid Section: Stainless Steel, End Port, NPT
Fluid Section Material: Stainless S

$5,590.00

QUANTM i30, 1" NPT, SS Elec dia pump, FluxCore drive, 120 VAC, AL centre, SS seat, PT ball, PO dia

GG TE30-0342

QUANTM PUMP, QTC-SSFC6SSPTPOPTS100

Graco TE30-0342 QUANTM i30, 1" NPT, Stainless Steel Electric Diaphragm Pump, 120 VAC 1Ph, AL Center, SS Seat, PT Ball, PO Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: The stainless-steel fluid section is designed to provide a high level of abrasion and corrosion resistance. With up to 8x more continuous torque at low speeds than conventional motors, this electric pump is an energy-saving workhorse that also delivers lower lifetime costs than less efficient pump technologies and is ideal for applications involving materials that are highly abrasive, paints, solvents or heated materials. This additional resilience means less downtime, which in turn provides a new opportunity to improve your bottom line. This powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework.

Revolutionary Design
Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
Quiet operation reduces plant noise and improves employee safety and health
Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor Powder-coated aluminum electric drive 120 VAC motor with 15 ft flying leadsCID1 Groups C,D,T4 Zone 1 AEx d b IIB T4 Gb hazardous location approval
Materials of Construction Stainless steel fluid section with NPT end portInternal components include 316 stainless steel seat, PTFE ball, PTFE overmold diaphragm and PTFE manifold o-ring

Model: QUANTM
Series: i30

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: PTFE

Center Section Material: Aluminum

Connection Type: NPT

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: PTFE Overmold

Fluid Inlet Size (in): 1
Fluid Inlet Size (mm): 25.4
Fluid Inlet Thread Gender: Female
Fluid Inlet Thread Type: NPT

Fluid Outlet Size (in): 1
Fluid Outlet Size (mm): 25.4
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT
Fluid Section: Stainless Steel, End Port, NPT
Fluid Section Material: Stainless Steel

$5,610.00

QUANTM i30, 1" NPT, Alum Elec dia pump, FluxCore drive, 120 VAC, AL centre, SS seat, PT ball, PS dia

GG TE30-0316

QUANTM PUMP, QTC-ALFC6SSPTPSPTA100

Graco TE30-0316 QUANTM i30, 1" NPT, Aluminum Electric Diaphragm Pump, 120 VAC 1Ph, AL Center, SS Seat, PT Ball, PS Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: The all-aluminum fluid section is specifically designed to be abrasion-resistant while also providing mild corrosion resistance. With up to 8x more continuous torque at low speeds than conventional motors, this general-purpose electric pump is an energy-saving workhorse that is ideal for sump evacuation applications as well as applications involving the evacuation of petroleum products (new and waste oils) and evacuation of solvents. This powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework. Not for use with halogenated hydrocarbons.

Revolutionary Design
Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
Quiet operation reduces plant noise and improves employee safety and health
Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor Powder-coated aluminum electric drive 120 VAC motor with 15 ft flying leadsCID1 Groups C,D,T4 Zone 1 AEx d b IIB T4 Gb hazardous location approval
Materials of Construction Aluminum fluid section with NPT end portInternal components include 316 stainless steel seat, PTFE ball, PTFE/Santoprene 2-piece diaphragm and PTFE manifold o-ring

Model: QUANTM
Series: i30

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: PTFE

Center Section Material: Aluminum

Connection Type: NPT

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: PTFE/Santoprene 2-Piece

Fluid Inlet Size (in): 1
Fluid Inlet Size (mm): 25.4
Fluid Inlet Thread Gender: Female
Fluid Inlet Thread Type: NPT

Fluid Outlet Size (in): 1
Fluid Outlet Size (mm): 25.4
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT
Fluid Section: Aluminum, End Port, NPT
Fluid Section Material: Aluminum

Hazardous Location Approval: Class 1, Division 1, ATEX, IECEx<

$4,010.00

QUANTM i30, 1" NPT, SS Elec dia pump, FluxCore drive, 120 VAC, AL centre, SS seat, SS ball, PO dia

GG TE30-0364

QUANTM PUMP, QTC-SSFC6SASDPOPTS100

Graco TE30-0364 QUANTM i30, 1" NPT, Stainless Steel Electric Diaphragm Pump, 120 VAC 1Ph, AL Center, SS Seat, SS Ball, PO Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: The stainless-steel fluid section is designed to provide a high level of abrasion and corrosion resistance. With up to 8x more continuous torque at low speeds than conventional motors, this electric pump is an energy-saving workhorse that also delivers lower lifetime costs than less efficient pump technologies and is ideal for applications involving materials that are highly abrasive, paints, solvents or heated materials. This additional resilience means less downtime, which in turn provides a new opportunity to improve your bottom line. This powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework.

Revolutionary Design
- Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
- Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
- Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
- Quiet operation reduces plant noise and improves employee safety and health
- Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor
- Powder-coated aluminum electric drive
- 120 VAC 1Ph motor with 15 ft flying leads
- CID1 Groups C,D,T4 Zone 1 AEx d b IIB T4 Gb hazardous location approval
Materials of Construction
- Stainless steel fluid section with NPT end port
- Internal components include 316 stainless steel seat, 316 stainless steel ball, PTFE overmold diaphragm and PTFE manifold o-ring

Model: QUANTM
Series: i30

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: 316 Stainless Steel

Center Section Material: Aluminum

Connection Type: NPT

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: PTFE Overmold

Fluid Inlet Size (in): 1
Fluid Inlet Size (mm): 25.4
Fluid Inlet Thread Gender: Female
Fluid Inlet Thread Type: NPT

Fluid Outlet Size (in): 1
Fluid Outlet Size (mm): 25.4
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT
Fluid Section: Stainless Steel, End Port, NPT
Fluid Section Material:

$5,750.00

QUANTM i120, 2" NPT, SS Elec Dia Pump, FluxCore drive, 240 V, AL Center, SS seat, PT ball, PS dia

GG TE120-0005

QUANTM PUMP, QTE-SSFC1SAPTPSPTS100

Graco TE120-0005 QUANTM i120, 2" NPT, Stainless Steel Electric Diaphragm Pump, 200-240 V, AL Center, SS Seat, PT Ball, PS Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: The stainless-steel fluid section is designed to provide a high level of abrasion and corrosion resistance. With up to 8x more continuous torque at low speeds than conventional motors, this electric pump is an energy-saving workhorse that also delivers lower lifetime costs than less efficient pump technologies and is ideal for applications involving materials that are highly abrasive, paints, solvents or heated materials. This additional resilience means less downtime, which in turn provides a new opportunity to improve your bottom line. This powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework.

Revolutionary Design
- Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
- Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
- Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
- Quiet operation reduces plant noise and improves employee safety and health
- Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor
- Powder-coated aluminum electric drive
- 240 VAC 3Ph motor with 15 ft cord and NEMA L15-20 plug
- Non-hazardous
Materials of Construction
- 316 stainless steel fluid section with NPT end port
- Internal components include 316 stainless steel seat, PTFE ball, PTFE/Santoprene 2-piece diaphragm and PTFE manifold o-ring

Model: QUANTM
Series: i120

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: PTFE

Center Section Material: Aluminum

Connection Type: NPT

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: PTFE/Santoprene 2-Piece

Fluid Inlet Size (in): 2
Fluid Inlet Size (mm): 51
Fluid Inlet Thread Gender: Female
Fluid Inlet Thread Type: NPT

Fluid Outlet Size (in): 2
Fluid Outlet Size (mm): 50.8
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT
Fluid Section: Stainless Steel, End Port, NPT
Fluid Section Material: Stainless Steel

Hazardous L

$12,000.00

QUANTM i30, 1in NPT, Stainless Steel Electric Diaphragm Pump, 120 VAC 1Ph, AL Center, SS Seat, SS Ball, FK Diaphragm

GG TE30-0093

QUANTM PUMP, QTC-SSFC5SASDFKPTS100

Graco TE30-0093 QUANTM i30, 1" NPT, Stainless Steel Electric Diaphragm Pump, 120 VAC 1Ph, AL Center, SS Seat, SS Ball, FK Diaphragm

QUANTM isn't just another electric pump: it's a game-changer. QUANTM features a revolutionary electric motor design that will reduce operational costs and delivers the reliability to keep your production lines running. With multiple fluid path options containing different materials of construction, QUANTM is ideal for most fluid applications as a highly reliable drop-in replacement for your current less-efficient pneumatic pumps or a perfect fit for greenfield construction. The unique self-priming, seal-less design delivers smooth and steady flow and is the only electric diaphragm pump on the market that stalls under pressure to reduce downtime caused by pump failures from clogged lines or closed valves. QUANTM is engineered to be quieter, more efficient and ultra-dependable while delivering energy savings that will go a long way to reinforcing your sustainability reputation. It's time to rethink your pump strategy and elevate your bottom line by converting to a QUANTM electric pump.

Application: The stainless-steel fluid section is designed to provide a high level of abrasion and corrosion resistance. With up to 8x more continuous torque at low speeds than conventional motors, this electric pump is an energy-saving workhorse that also delivers lower lifetime costs than less efficient pump technologies and is ideal for applications involving materials that are highly abrasive, paints, solvents or heated materials. This additional resilience means less downtime, which in turn provides a new opportunity to improve your bottom line. This powerful new pump delivers a higher level of reliability to minimize downtime while the plug-and-play design makes it easy to drop into any production line without additional investment or infrastructure rework.

Revolutionary Design
- Replace existing air operated pumps with electric pump technology that stalls under pressure and includes AutoPrime feature
- Compact and efficient electric drive removes the gearbox providing a comparable footprint to a pneumatic diaphragm pump
- Up to 80% reduction in energy consumption compared to pneumatic pumps, reducing operating costs and providing a quick investment payback
- Quiet operation reduces plant noise and improves employee safety and health
- Smart pump control provides more accurate flow set points and built-in I/O
Efficient Electric Motor
- Powder-coated aluminum electric drive
- 120 VAC 1Ph motor with 15 ft cord and NEMA 5-15 plug
- Non-hazardous
Materials of Construction
- Stainless steel fluid section with NPT end port
- Internal components include 316 stainless steel seat, 316 stainless steel ball, FKM (Viton) diaphragm and PTFE manifold o-ring

Model: QUANTM
Series: i30

Application: Chemical Processing, Paints and Coatings, Waste Water, General Fluid Transfer

Ball Material: 316 Stainless Steel

Center Section Material: Aluminum

Connection Type: NPT

Cord Length (ft): 15
Cord Length (m): 4.57

Diaphragm Material: FKM (Viton)

Fluid Inlet Size (in): 1
Fluid Inlet Size (mm): 25.4
Fluid Inlet Thread Gender: Female
Fluid Inlet Thread Type: NPT

Fluid Outlet Size (in): 1
Fluid Outlet Size (mm): 25.4
Fluid Outlet Thread Gender: Female
Fluid Outlet Thread Type: NPT
Fluid Section: Stainless Steel, End Port, NPT
Fluid Section Material: Stainless Steel

Hazardous L

$5,560.00