ENERPAC S100272

EP LGM306

• Type: Puller

• Product Group: Pullers
• Product Line: Industrial Tools
• Series: LGM
• SubTypes: Lock-Grip Puller Mechanical

• Capacity Imperial Tons: 6
• Capacity KN: 48,9

• LGM-Series Pullers are an ideal solution for pulling small to medium-size wheels, sprockets, bearings and other similar shaft mounted parts. The puller's selfcentering closing system allows all jaws to move simultaneously, making it easy for a single operator to mount the puller and to perform the application. Turning the puller handle locks the jaws onto the application, allowing the desired object to be pulled free when the spindle is turned.
• Quickly and easily mount on a wide range of applications
• Lock-on jaws offer a secure grip for safe and easy operation
• Synchronous jaw movement enables entire pulling job to be performed by a single operator
• LGM-Series Pullers MUST be used with a point protector if the shaft end does not contain a drilled center hole. One point protector is included with every puller.
• Always wear safety goggles and gloves while using pullers.

• Set Includes: SGM0404

EP LH50

• Type: Tension Meter and Load Cell

• Product Group: Presses
• Product Line: Industrial Tools
• Series: LH
• SubTypes: Direct Mounted Load Cell

• Accuracy, plus/minus2% of full scale
• Zinc and bronze plated to resist rust and corrosion
• Dual-range readout in kilograms and pounds
• Cushioned metal case provides safe storage and transport
• Maximum indicating pointer reading for pre-selected forces or to maintain maximum force readings
• TM and LH models are 100% tested to verify accuracy within a plus/minus2% range. If your application requires a calibrated tool, it must be submitted for certification testing. Certification is NOT available from Enerpac.

EP LH5006

• Type: Tension Meter and Load Cell

• Product Group: Presses
• Product Line: Industrial Tools
• Series: LH
• SubTypes: Remote Mounted Load Cell

• Accuracy, plus/minus2% of full scale
• Zinc and bronze plated to resist rust and corrosion
• Dual-range readout in kilograms and pounds
• Cushioned metal case provides safe storage and transport
• Maximum indicating pointer reading for pre-selected forces or to maintain maximum force readings
• TM and LH models are 100% tested to verify accuracy within a plus/minus 2% range. If your application requires a calibrated tool, it must be submitted for certification testing. Certification is NOT available from Enerpac.

EP LH5006K

• Type: Service Kit

• SubTypes: Seal Kit

EP M24040

• Type: Service Kit

• SubTypes: Plunger Kit

EP MHV1K

• Type: ERP

EP MK106

• The Simplex MK106 Maintenance Kit provides a complete assortment of attachments that greatly expands the range of applications. Using thesevarious attachments allows you to custom build spreaders, straightening tools, clamps and a wide variety of other problem solving maintenancetools.
• Set includes a Simplex hand pump, cylinder, hose, gauge and gauge adaptor.
• Heavy duty case included.
• Rated at 5 tons when attachments are used.
• Quick lock and threaded adaptors included.
• Order as a set or individual components.
• R106 is rated at 10 tons at 10,000 psi. When using attachments or extensions do not exceed 5,000 psi (5 tons) reading on the gauge. Accessories & extensions are only rated at 5 tons. S2000A Spreader has an operating capacity of 1 ton.
• Add collar toe and flat base to build custom spreader or toe jack.
• Extensions, custom heads and adapters allow you to create tools that solve hundreds of problems. Simplex MK106 kits are used extensively for collision repair.
• Add a V-base and flat base for special spreading, holding and bending jobs.

• Type: Cylinder And PumpSet
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: MK
• Stroke Inches: 6
• Stroke MM: 152.4
• SubTypes: Steel General Purpose Cylinder and Steel Hand Pump Set with 17 Cylinder Attachments

• Capacity Imperial Tons: 10
• Capacity KN: 89,0

• Set Includes: R106, P42, HCA6, G5, GA1-Simplex, S2000A, MK4, MK5, MK6, MK7, MK8, MK9, MK10, MK11, MK12, MK13, MK14, MK15, MK16, MK17, MK18, MK19, MK20, MK21

EP MMR30K

• Type: Service Kit

EP MPK2

• Type: Service Kit

• SubTypes: Manifold Kit

EP MRS3001

• Type: Hydraulic Cylinders
• Max Bar: 350
• Max PSI: 5000

• Product Group: Cylinders and Jacks
• Product Line: Work Holding Tools
• Series: MRS
• SubTypes: Workholding Positive Clamping Cylinder

• Heavy disk springs maintain the clamping force - hydraulic pressure is used for release
• Single-acting design allows easy setup of hydraulic system
• Hollow plunger design allows easy retrofit for mechanical clamping
• Custom buttons can be fitted into the plunger for clamping directly against a workpiece
• Threaded body allows easy cylinders mounting directly into fixture plate
• Internal threaded plunger allows accessories to be used easily for retrofit applications

• Accessories: BS202

EP MS21020

The MS21020 is our most complete maintenance set that equips you to complete a wide array of maintenance tasks. The assortment of 53 accessories enables you to quickly configure the ideal tool for just about any challenge imaginable.

This set includes three of our most popular hydraulic cylinders: The RC102, RC106, and the RC256. Using these cylinders with attachments will allow you to exert at forces up to 12.5 tons (116kN) and extend up to 6.25" (116mm) - Ideal when you need to push, pull, lift, press, straighten, spread, or clamp.

Also included is the lightweight P392 2-speed hydraulic hand pump, hose, gauge, A92 spreader attachment, lock-on or threaded connectors, and a storage crate.

Safe Operation
When using hydraulic cylinders with maintenance set attachments or components, the maximum system pressure must be limited to half of the rated pressure (5,000 psi / 350 bar). When not using attachments, the tonnage and pressure capacities are double these values.

Only use attachments provided with the set. Using non-Enerpac attachments and longer extension tubes could reduce column strength - potentially creating unsafe conditions.

• Type: Cylinder And PumpSet
• Max Bar: 350
• Max PSI: 5000

• Product Group: Cylinders and Jacks, Pumps
• Product Line: Industrial Tools
• Series: MS
• Stroke Inches: 6.25
• Stroke MM: 158
• SubTypes: Cylinder with Attachments and Hand Pump Set

• Set Includes: P392, HC7206, RC102, RC106, RC256, GP10S, GA2, A13, A28, A21, A27, A20, A595, A14, A243, A10, A8, A6, A192, A305, A18, A185, A15, A607, A129, A128, A132, A238, A5, A141, A218, A19, A242, A92, A16, MZ1050, MZ1051, MZ1052, A285, MZ1002, MZ1003, A239, MZ1004, A240, MZ1005, A241, CW350

EP MS220

This hydraulic pump and cylinder set includes a complete assortment of accessories allowing you to quickly configure a unique tool to solve your many difficult maintenance tasks.

The set includes the RC256 Hydraulic Cylinder, which when used with attachments allows you to exert a force of 12.5 tons (116kN) and a stroke of 6.25" (116mm). Ideal when you need to push, pull, lift, press, straighten, or clamp.

Also included is the lightweight P392 2-speed hydraulic hand pump, hose, gauge, lock-on or threaded connectors, and a storage crate.

Safe Operation
When using hydraulic cylinders with maintenance set attachments or components, the maximum system pressure must be limited to half of the rated pressure (5,000 psi / 350 bar). When not using attachments, the tonnage and pressure capacities are double these values.

Only use attachments provided with the set. Using non-Enerpac attachments and longer extension tubes could reduce column strength - potentially creating unsafe conditions.

• Type: Cylinder And PumpSet
• Max Bar: 350
• Max PSI: 5000

• Product Group: Cylinders and Jacks, Pumps
• Product Line: Industrial Tools
• Series: MS
• Stroke Inches: 6.25
• Stroke MM: 158
• SubTypes: Cylinder with Attachments and Hand Pump Set

• Set Includes: P392, HC7206, RC256, GP10S, GA2, A28, A27, A595, A243, A607, A238, A218, A242, A239, A240, A241, CW166

EP MVK2

• Type: Service Kit

• SubTypes: Repair Kit

EP MVK3

• Type: Service Kit

• SubTypes: Repair Kit

EP MVPM5

• Type: Valve
• Max Bar: 350
• Max PSI: 5000

• Product Group: Valves, Pumps
• Product Line: Work Holding Tools
• Series: MVP
• SubTypes: Sequence Valve

• Sequence valves block the oil to a secondary hydraulic circuit until pressure in the primary circuit reaches a preset level. The sequence valves have a built-in check system to allow the oil to flow back without external piping.
• Direct accurate pressure setting
• Pressure setting between 500-5000 psi for secondary circuit is secured with lock nut
• Manifold mounting ports on MVPM5
• Manifold O-rings included with MVPM5

EP NC2432

NC-Series Hydraulic Nut Splitters use a single blade configuration suited to general nut cutting applications across a wide range of industries.

The heat-treated steel blade with its optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NC-Series Nut Cutters are compact, simple, and easy to use. The ergonomic design ensures comfortable use, thanks to the carefully considered angled head design and handle position.

Nuts are often difficult to remove, and while loosening them using tightening tools is possible, this generally requires larger equipment and takes more time.

Using a cutting torch or a hammer and chisel presents safety risks and can cause damage to the joint components. They also involve significantly longer setup and operational time.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NC
• SubTypes: Nut Cutter

• bundleSet_IDs: NCB2432
• Capacity Imperial Tons: 15
• Capacity KN: 147

• Compact and ergonomic design, easy to use
• Unique angled head design
• Single-acting, spring return cylinder
• Heavy duty chisels can be reground
• Nut Splitters include spare chisel, spare set screw and wrench used to secure the chisel. A CR-400 coupler is standard.
• For applications with bolt sizes that are common to two tool model sizes, we recommend to select the larger of the two tools for the best results.
• These are not suited for square, star, round or stainless steel nuts. Maximum allowable hardness of nuts to be split is HRc-44.
• For materials and sizes not specified, contact Enerpac Technical Services.

• Accessories: NCB2432

EP NC3241

NC-Series Hydraulic Nut Splitters use a single blade configuration suited to general nut cutting applications across a wide range of industries.

The heat-treated steel blade with its optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NC-Series Nut Cutters are compact, simple, and easy to use. The ergonomic design ensures comfortable use, thanks to the carefully considered angled head design and handle position.

Nuts are often difficult to remove, and while loosening them using tightening tools is possible, this generally requires larger equipment and takes more time.

Using a cutting torch or a hammer and chisel presents safety risks and can cause damage to the joint components. They also involve significantly longer setup and operational time.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NC
• SubTypes: Nut Cutter

• Capacity Imperial Tons: 20
• Capacity KN: 196

• Compact and ergonomic design, easy to use
• Unique angled head design
• Single-acting, spring return cylinder
• Heavy duty chisels can be reground
• Nut Splitters include spare chisel, spare set screw and wrench used to secure the chisel. A CR-400 coupler is standard.
• For applications with bolt sizes that are common to two tool model sizes, we recommend to select the larger of the two tools for the best results.
• These are not suited for square, star, round or stainless steel nuts. Maximum allowable hardness of nuts to be split is HRc-44.
• For materials and sizes not specified, contact Enerpac Technical Services.

• Accessories: NCB3241

EP NC4150

NC-Series Hydraulic Nut Splitters use a single blade configuration suited to general nut cutting applications across a wide range of industries.

The heat-treated steel blade with its optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NC-Series Nut Cutters are compact, simple, and easy to use. The ergonomic design ensures comfortable use, thanks to the carefully considered angled head design and handle position.

Nuts are often difficult to remove, and while loosening them using tightening tools is possible, this generally requires larger equipment and takes more time.

Using a cutting torch or a hammer and chisel presents safety risks and can cause damage to the joint components. They also involve significantly longer setup and operational time.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NC
• SubTypes: Nut Cutter

• bundleSet_IDs: NCB4150
• Capacity Imperial Tons: 35
• Capacity KN: 343

• Compact and ergonomic design, easy to use
• Unique angled head design
• Single-acting, spring return cylinder
• Heavy duty chisels can be reground
• Nut Splitters include spare chisel, spare set screw and wrench used to secure the chisel. A CR-400 coupler is standard.
• For applications with bolt sizes that are common to two tool model sizes, we recommend to select the larger of the two tools for the best results.
• These are not suited for square, star, round or stainless steel nuts. Maximum allowable hardness of nuts to be split is HRc-44.
• For materials and sizes not specified, contact Enerpac Technical Services.

• Accessories: NCB4150

EP NC6075

NC-Series Hydraulic Nut Splitters use a single blade configuration suited to general nut cutting applications across a wide range of industries.

The heat-treated steel blade with its optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NC-Series Nut Cutters are compact, simple, and easy to use. The ergonomic design ensures comfortable use, thanks to the carefully considered angled head design and handle position.

Nuts are often difficult to remove, and while loosening them using tightening tools is possible, this generally requires larger equipment and takes more time.

Using a cutting torch or a hammer and chisel presents safety risks and can cause damage to the joint components. They also involve significantly longer setup and operational time.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NC
• SubTypes: Nut Cutter

• Capacity Imperial Tons: 90
• Capacity KN: 882

• Compact and ergonomic design, easy to use
• Unique angled head design
• Single-acting, spring return cylinder
• Heavy duty chisels can be reground
• Nut Splitters include spare chisel, spare set screw and wrench used to secure the chisel. A CR-400 coupler is standard.
• For applications with bolt sizes that are common to two tool model sizes, we recommend to select the larger of the two tools for the best results.
• These are not suited for square, star, round or stainless steel nuts. Maximum allowable hardness of nuts to be split is HRc-44.
• For materials and sizes not specified, contact Enerpac Technical Services.

• Accessories: NCB6075

EP NCB1924

• Type: Cutter Accessory

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NCB
• SubTypes: Replacement Chisel

EP NCB2432

• Type: Cutter Accessory

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NCB
• SubTypes: Replacement Chisel

EP NCB3241

• Type: Cutter Accessory

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NCB
• SubTypes: Replacement Chisel

EP NCB4150

• Type: Cutter Accessory

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NCB
• SubTypes: Replacement Chisel

EP NSH1927

NSH-Series Hydraulic Nut Splitters are suited to flange nut splitting jobs in the oil and gas industries.

The heat-treated steel blade with optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NSH-Series Nut Cutters are simple and easy to use. They include an ergonomically designed revolving handle for comfortable working and to isolate shock and vibration. The supplied lanyard and revolving anchor point are drop tested to ensure safety.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NSH
• SubTypes: Nut Splitter

• Capacity Imperial Tons: 12
• Capacity KN: 120

• Quick and easy cutting tip replacement
• Drop-tested revolving anchor point and safety lanyard
• Revolving composite handle for vibration and shock isolation
• Nut Splitters include set of hexagon keys and following spare parts:
  - cutting tip
  - tip retention screw
  - spare alignment screw
• Standard Safety Lanyard with each nut splitter. Includes steel cable with carabiners.
• CR400 female half coupler is standard
• Maximum allowable hardness to split is ASTM A194 Gr 2H. Not to be used on square nuts or stainless steel.

• Set Includes: CR400, FSC1
• Accessories: NSH1927CTK

EP P141K2

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P142ALSS

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P
• SubTypes: Hand Pump - Two Speed

• Corrosion resistant, nickel-plated valves and cylinders
• Stainless steel pump inserts will not corrode
• Viton Seals provide heat and chemical resistance
• Anodized aluminum pump reservoirs and plastic encapsulated pump bodies resist wet environments
• Two-speed operation reduces pump handle strokes 78% compared to single-speed pumps
• Pump handles lock for easy carrying

• Spare Part(s): DA8802900SR, P142ALSSK

EP P202K1

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P181190W

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Relief Valve

EP P20857

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Crosspin

EP P25

These Low-Pressure Hydraulic Hand Pumps are durable, portable, highly efficient, and easy to use. Each model in the series features an all-steel construction, a chrome plated plunger, and a wiper system for long-lasting performance.

These pumps are constructed to power a wide range of single acting cylinders and tools in space restricted areas. The range includes the P51 that can be operated in the horizontal orientation only, and others also capable of operating in the vertical orientations: P18 with the pump head facing down, P25, P50 with the pump head facing up. Each is protected by external load-release valves and internal overload pressure-relief valves.

With a choice of oil capacities up to 200 in3 (3,277 cm3), and operating pressures of 2,500 psi (175 bar) - 5,000 psi (350 bar) you will find an Enerpac Low Pressure Hydraulic Hand Pump to suit your needs.

• Type: Hydraulic Pump
• Max Bar: 175
• Max PSI: 2500

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P
• SubTypes: Hand Pump - Single Speed

• P25 and P50 pumps oil in both forward and reverse handle movement improving overall efficiency, ideal when mounting space is restricted
• External load-release valve
• Internal pressure-relief valve for overload protection
• P25 and P50 vertical operation requires pump vent side facing up

• Spare Part(s): CA365024SR, P181190W, P50K1

EP P391K2

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P30718

• Type: Service Kit

• SubTypes: Repair Part

EP P301D

• Heavy duty, metal construction for durability.
• High displacements of oil per stroke.
• Low, back saving handle effort.
• Large reservoir capacities.

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: P Steel
• SubTypes: Hand Pump - Heavy Duty Steel

EP P392E024K

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P39K4

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P84K3

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P84HDK

• Type: Service Kit

• SubTypes: Handle

EP P39K5

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P45138

• Type: Service Kit

• SubTypes: Screw

EP P77K1

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P39RVK

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Valve Assembly

EP P84VRK

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Valve Assembly

EP PA1065040

• Type: Component

EP P50K1

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P (Service Kit)
• SubTypes: Repair Kit

EP P6012SR

• Type: Service Kit

• SubTypes: Repair Part

EP P6010

• Type: Service Kit

• SubTypes: Spindle Repair Kit

EP P75181

• Type: Service Kit

• SubTypes: Nut

EP P80K8

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P60234-1SR

• Type: Service Kit

• SubTypes: Repair Part

EP P6012

• Type: Service Kit

• SubTypes: Repair Part

EP P51K1

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P (Service Kit)
• SubTypes: Repair Kit

EP P80K4

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Repair Kit

EP P45139

• Type: Service Kit

• SubTypes: Washer

EP P51

These Low-Pressure Hydraulic Hand Pumps are durable, portable, highly efficient, and easy to use. Each model in the series features an all-steel construction, a chrome plated plunger, and a wiper system for long-lasting performance.

These pumps are constructed to power a wide range of single acting cylinders and tools in space restricted areas. The range includes the P51 that can be operated in the horizontal orientation only, and others also capable of operating in the vertical orientations: P18 with the pump head facing down, P25, P50 with the pump head facing up. Each is protected by external load-release valves and internal overload pressure-relief valves.

With a choice of oil capacities up to 200 in3 (3,277 cm3), and operating pressures of 2,500 psi (175 bar) - 5,000 psi (350 bar) you will find an Enerpac Low Pressure Hydraulic Hand Pump to suit your needs.

• Type: Hydraulic Pump
• Max Bar: 200
• Max PSI: 3000

• Product Group: Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: P
• SubTypes: Hand Pump - Single Speed

• External load-release valve
• Internal pressure-relief valve for overload protection
• P51 for horizontal operation only

• Spare Part(s): CJ589950W, P181190W, P51K1

EP P6011

• Type: Service Kit

• SubTypes: Nut

EP P80SFK

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Valve Repair Kit

EP P75266-1

• Type: Service Kit

• SubTypes: Reservoir Assembly

EP P464

Ultima Steel Hand Pumps are durable, portable, and highly efficient. Each model in the series features an all-steel construction, a chrome plated plunger, and a wiper system for long-lasting performance.

All except the P39 are 2 stage pumps, which reduces the number of handle strokes by as much as 78% compared to a single speed pump. This is ideal for applications when high flow is needed at the first stage, (such as when advancing a cylinder to the point of load contact). The pump switches automatically to the second stage which is the low flow high-pressure stage.

With a choice of oil capacities up to 453 in3 (7423 cm3), you will find Ultima Steel Hand Pumps that can handle multiple cylinder hook-ups, including models to suit either single-acting and double-acting cylinders.

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P
• SubTypes: Hand Pump - Two Speed

• Reduced handle effort and ergonomic grip for less operator fatigue
• Vent free reservoir eliminates spills
• Quick grip handle allows for easy transport
• Integral reservoir over-pressurization protection

• Spare Part(s): P462K2, P462K3

EP P462K3

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P (Service Kit)
• SubTypes: Repair Kit

EP PA133K3

• Type: Service Kit

• Product Group: Pumps
• SubTypes: Repair Kit

EP PACG30S8SWM10

Enerpac PACG Air Hydraulic Pumps are for designed for intermittent to medium duty workholding applications up to 5,000 psi. Valve mount options include, remote, and mountings for DO3 and VP valves.

Enerpac Turbo II Air Over Hydraulic Pumps generate the hydraulic pressure you need using the air pressure you have available. The Air Saver Piston reduces air consumption, and the pump can start at low pressures from 50-125 psi.

Turbo II Air-Hydraulic Pumps are best suited to medium or lower cycle applications. They provide the power and speed needed for simple clamping circuits and mostly single acting tools. At only 75 dBA, the Turbo II Series helps to keep the noise level to a minimum.

Choose from a range with maximum working pressure of either 5,000 or 10,000psi, and various reservoir capacities from 116 - 462 in3 (2100 - 7500 cm3).

Turbo II Air Over Hydraulic Pump Series :

• PATG - Treadle for foot or hand operation
• PARG - Pendant Operation
• PAMG - Manual lever operated. For double-acting applications
• PACG - For remote valve mount. For workholding, 5000 psi (350 bar).
• PASG - Includes mount for a single DO3 Valve. For workholding, 5000 psi (350 bar).

• Type: Hydraulic Pump
• Max Bar: 350
• Max PSI: 5000

• Product Group: Pumps
• Product Line: Work Holding Tools
• Series: PACG
• SubTypes: Air Pump

• On-demand stall-restart operation maintains system pressure, providing clamping security
• External adjustable pressure relief valve (behind sight glass)
• Internal pressure relief valve provides overload protection
• Reduced noise level to 75 dBA
• Operating air pressure: 50-125 psi - enables pump to start at low air pressure**
• Hydraulic to air ratio: 45:1
• Reinforced heavy-duty lightweight reservoir for applications in tough environments
• Five valve mounting options provide flexibility in setup and operation
• Fully serviceable air motor assembly
• User supplied valves

** NOTE: From 50-125 psi air inlet pressure. Performance is significantly diminished below 50 psi. Performance may vary compared to listed values due to seal friction, internal pressure drops and manufacturing tolerances. Be sure to allow some flexibility on air inlet pressure.

EP PACG5002SB

Enerpac PACG Air Hydraulic Pumps are for designed for intermittent to medium duty workholding applications up to 5,000 psi. Valve mount options include, remote, and mountings for DO3 and VP valves.

Enerpac Turbo II Air Over Hydraulic Pumps generate the hydraulic pressure you need using the air pressure you have available. The Air Saver Piston reduces air consumption, and the pump can start at low pressures from 50-125 psi.

Turbo II Air-Hydraulic Pumps are best suited to medium or lower cycle applications. They provide the power and speed needed for simple clamping circuits and mostly single acting tools. At only 75 dBA, the Turbo II Series helps to keep the noise level to a minimum.

Choose from a range with maximum working pressure of either 5,000 or 10,000psi, and various reservoir capacities from 116 - 462 in3 (2100 - 7500 cm3).

Turbo II Air Over Hydraulic Pump Series :

• PATG - Treadle for foot or hand operation
• PARG - Pendant Operation
• PAMG - Manual lever operated. For double-acting applications
• PACG - For remote valve mount. For workholding, 5000 psi (350 bar).
• PASG - Includes mount for a single DO3 Valve. For workholding, 5000 psi (350 bar).

• Type: Hydraulic Pump
• Max Bar: 350
• Max PSI: 5000

• Product Group: Pumps
• Product Line: Work Holding Tools
• Series: PACG
• SubTypes: Air Pump

• On-demand stall-restart operation maintains system pressure, providing clamping security
• External adjustable pressure relief valve (behind sight glass)
• Internal pressure relief valve provides overload protection
• Reduced noise level to 75 dBA
• Operating air pressure: 50-125 psi - enables pump to start at low air pressure**
• Hydraulic to air ratio: 45:1
• Reinforced heavy-duty lightweight reservoir for applications in tough environments
• Five valve mounting options provide flexibility in setup and operation
• Fully serviceable air motor assembly
• User supplied valves

** NOTE: From 50-125 psi air inlet pressure. Performance is significantly diminished below 50 psi. Performance may vary compared to listed values due to seal friction, internal pressure drops and manufacturing tolerances. Be sure to allow some flexibility on air inlet pressure.

EP PAM1042K3

• Type: Service Kit

• Product Group: Pumps
• SubTypes: Repair Kit

EP PAMG3400K

• Type: Service Kit

• SubTypes: Repair Part

EP PAMG5400K

• Type: Service Kit

EP PARG1102N

Enerpac Turbo II Air Over Hydraulic Pumps generate the hydraulic pressure you need using the air pressure you have available. The Air Saver Piston reduces air consumption, and the pump can start at low pressures from 50-125 psi.

Turbo II Air-Hydraulic Pumps are best suited to medium or lower cycle applications. They provide all the power and speed needed for simple clamping circuits and mostly single acting tools. At only 75 dBA, the Turbo II Series helps to keep the noise level to a minimum.

Choose from a range with maximum working pressure of either 5,000 or 10,000psi, and various reservoir capacities from 116 - 462 in3 (2100 - 7500 cm3).

Each PARG pump variant includes a 3-way, 3-position valve for Advance / Hold / Retract functions.

Turbo II Air Over Hydraulic Pump Series :

• PATG - Treadle for foot or hand operation
• PARG - Pendant Operation
• PAMG - Manual lever operated. For double-acting applications
• PACG - For remote valve mount. For work holding, 5000 psi (350 bar).
• PASG - Includes mount for a single DO3 Valve.

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: PARG
• SubTypes: Air Pump

• High efficiency cast aluminum air motor for increased life and reduced air consumption
• Reinforced heavy-duty reservoir for applications in tough environments
• New generation air saver piston with rugged one-piece design reduces air consumption and operating costs
• Return-to-tank port for use in remote valve applications
• Quiet - only 76dBA with low air consumption of 12 scfm
• Operating air pressure: 40-125 psi, enables pump to start at extremely low pressure
• Internal pressure relief valve provides overload protection

EP PAMG1402N

PAMG Series air over hydraulic pumps include a manual lever operated 3-way valve. As part of the Turbo II Air Hydraulic Series, they provide the power and speed needed for simple clamping circuits.

PAMG3402NB, PAMG34S8N, PAMG5402NB, PAMG54S8N are for single-acting applications with a maximum operation pressure of 5000 psi (350 bar).

The PAMG1405N and the PAMG1402N pumps are compatible with double acting tools and provide Advance / Hold / Retract functions. Maximum operating pressure of 10,000 psi (700 bar).

Enerpac Turbo II Air Over Hydraulic Pumps generate the hydraulic pressure you need using the air pressure available. The Air Saver Piston reduces air consumption, and the pump can start at low pressures from 50-125 psi.

Turbo II Air-Hydraulic Pumps are best suited to medium or lower cycle applications. They provide all the power and speed needed for simple clamping circuits and single acting tools. At only 75 dBA, the Turbo II Series helps to keep the noise level to a minimum.

Choose from a range with maximum working pressure of either 5,000 or 10,000psi, and various reservoir capacities from 116 - 462 in3 (2100 - 7500 cm3).

Turbo II Air Over Hydraulic Pump Series :

• PATG - Treadle for foot or hand operation
• PARG - Pendant Operation
• PAMG - Manual lever operated. For double-acting applications
• PACG - For remote valve mount. For work holding, 5000 psi (350 bar).
• PASG - Includes mount for a single DO3 Valve.

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: PAMG
• SubTypes: Air Pump

• High efficiency cast aluminum air motor for increased life and reduced air consumption
• Reinforced heavy-duty reservoir for applications in tough environments
• New generation air saver piston with rugged one-piece design reduces air consumption and operating costs
• Return-to-tank port for use in remote valve applications
• Quiet - only 76dBA with low air consumption of 12 scfm
• Operating air pressure: 40-125 psi, enables pump to start at extremely low pressure
• Internal pressure relief valve provides overload protection

EP PATG1100K

• Type: Service Kit

• SubTypes: Repair Part

EP PARG1105N

Enerpac Turbo II Air Over Hydraulic Pumps generate the hydraulic pressure you need using the air pressure you have available. The Air Saver Piston reduces air consumption, and the pump can start at low pressures from 50-125 psi.

Turbo II Air-Hydraulic Pumps are best suited to medium or lower cycle applications. They provide all the power and speed needed for simple clamping circuits and mostly single acting tools. At only 75 dBA, the Turbo II Series helps to keep the noise level to a minimum.

Choose from a range with maximum working pressure of either 5,000 or 10,000psi, and various reservoir capacities from 116 - 462 in3 (2100 - 7500 cm3).

Each PARG pump variant includes a 3-way, 3-position valve for Advance / Hold / Retract functions.

Turbo II Air Over Hydraulic Pump Series :

• PATG - Treadle for foot or hand operation
• PARG - Pendant Operation
• PAMG - Manual lever operated. For double-acting applications
• PACG - For remote valve mount. For work holding, 5000 psi (350 bar).
• PASG - Includes mount for a single DO3 Valve.

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: PARG
• SubTypes: Air Pump

• High efficiency cast aluminum air motor for increased life and reduced air consumption
• Reinforced heavy-duty reservoir for applications in tough environments
• New generation air saver piston with rugged one-piece design reduces air consumption and operating costs
• Return-to-tank port for use in remote valve applications
• Quiet - only 76dBA with low air consumption of 12 scfm
• Operating air pressure: 40-125 psi, enables pump to start at extremely low pressure
• Internal pressure relief valve provides overload protection

EP PE10000SR

• Type: ERP

• SubTypes: Repair Part

EP PJ3P

• Side locking screw keeps the jack extended and prevents lowering due to vibration.
• Screw operation provides countless adjustments for exact leveling.
• Ideal jack for leveling plane beds, millers and machinery.
• Ball and socket cap swivels to center load forces.
• Notched base fastens easily to machine beds.
• CE Compliant - Our Jack design specifications meet or exceed ANSI /ASME B30.1 Safety Standards.
• Slotted load cap prevents the load from possible slippage with inline applications.

• Type: Jack

• Product Line: Mechanical Tools
• Series: PJ
• Stroke Inches: 2.25
• Stroke MM: 57.2
• SubTypes: Planer Jack

• Capacity Imperial Tons: 6
• Capacity KN: 53,4

EP PMB2

• Type: Press Accessory

• Product Group: Presses
• Product Line: Industrial Tools
• Series: A
• SubTypes: Press Pump Mounting Bracket

• Heavy duty steel brackets to allow conversion to one of the Enerpac Power Sources to power your press.
• Both mounting brackets are pre-drilled to accept a number of different pump models

EP PME10427K

• Type: Service Kit

• Product Group: Pumps
• Series: PME repair kit
• SubTypes: Repair Kit

EP PP179017

• Type: Service Kit

• SubTypes: Retaining Ring

EP PRASA10016L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 16
• Stroke MM: 406
• SubTypes: POW'R-RISER Jack Pneumatic

• Capacity Imperial Tons: 100
• Capacity KN: 889

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS60, PRU13, PRU14, PRU110, PRUS126, PRE5, PRE7, PRE9, PRE11, PRE14, PRE18, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PRASA10027L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 27
• Stroke MM: 686
• SubTypes: POW'R-RISER Jack Pneumatic

• Capacity Imperial Tons: 100
• Capacity KN: 889

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS60, PRU13, PRU14, PRU110, PRUS137, PRE5, PRE7, PRE9, PRE11, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PRASA15027L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 26.5
• Stroke MM: 673
• SubTypes: POW'R-RISER Jack Pneumatic

• Capacity Imperial Tons: 150
• Capacity KN: 1333

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS150, PRU151, PRU153, PRU155, PRU1510, PRUS1537, PRE5, PRE7, PRE9, PRE11, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PTW1000C

• Type: Torque Wrench

• Product Group: Torque Wrenches, Torque Wrench Pumps
• Product Line: Bolting Tools
• Series: PTW
• SubTypes: Pneumatic Torque Wrench with FRL

• High speed continuous rotation for constant torque output
• Low friction planetary gearbox design minimizes wear and extends uptime
• Ergonomic, low vibration design reduces fatigue and the risk of vibration related injuries for the operator
• Low noise air motor provides quiet, consistent performance for indoor and outdoor applications
• Provided with standard reaction arm; wide assortment of custom arms and accessories are available
• Available with or without Filter-Regulator-Lubricator (FRL)
• Unique calibration certificate provided with each tool

• Set Includes: RATWS, FRL120C
• Accessories: ED6TWS, ED12TWS, ED18TWS, RATWS, ERATWS, SLRATWS, DSATWS, SRATWS, BLTWS

EP PTW2000C

• Type: Torque Wrench

• Product Group: Torque Wrenches, Torque Wrench Pumps
• Product Line: Bolting Tools
• Series: PTW
• SubTypes: Pneumatic Torque Wrench with FRL

• High speed continuous rotation for constant torque output
• Low friction planetary gearbox design minimizes wear and extends uptime
• Ergonomic, low vibration design reduces fatigue and the risk of vibration related injuries for the operator
• Low noise air motor provides quiet, consistent performance for indoor and outdoor applications
• Provided with standard reaction arm; wide assortment of custom arms and accessories are available
• Available with or without Filter-Regulator-Lubricator (FRL)
• Unique calibration certificate provided with each tool

• Set Includes: RATWS, FRL120C
• Accessories: ED6TWS, ED12TWS, ED18TWS, RATWS, ERATWS, SLRATWS, DSATWS, SRATWS, BLTWS

EP PUD1100B

PU Series electric over hydraulic pumps combine economy with high-performance - ideal for intermittent use when working with small to medium size cylinders and other hydraulic tools.

All models in the series are 2-speed for enhanced productivity, and each is supplied with a 10 ft (3 m) cord and control pendant for operator safety. The high-strength molded shroud with integral handle protects the motor from contamination and damage in industrial environments.

Within the PU Series is a selection of pumps that offer a choice of reservoir capacities, valve functions and voltage.

PUD1100 Series

• For advance and retract of single-acting cylinders
• For applications not requiring load holding
• Ideal for punching applications

PUD1300 Series

• Providing advance, hold, and retract of single-acting cylinders
• Ideal for applications requiring load holding
• For applications requiring solenoid valves

PUJ-Series

• Manual valves provide advance, hold, and retract operation
• 3 and 4-way valves for single or double-acting cylinders

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: PU
• SubTypes: Electric Pump - Economy

• The economic choice for small to medium sized tools.
• Lightweight, compact, and portable.
• Two-speed operation reduces cycle times for improved productivity.
• Ideal for intermittent duty cycles.
• Works well with long extension cords or generator-driven electrical power supplies.
• 115 VAC 50/60-cycle universal motor will operate under poor voltage supply.
• 24 VAC remote motor control with 10 ft (3 m) cord for operator safety.
• Starts under full load.
• High-strength shroud with integral handle protects the motor from contamination and damage.

• Spare Part(s): PUD1100BK

EP PREMB10016L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 16
• Stroke MM: 406
• SubTypes: POW'R-RISER Jack Electric

• Capacity Imperial Tons: 100
• Capacity KN: 889

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS60, PRU13, PRU14, PRU110, PRUS126, PRE5, PRE7, PRE9, PRE11, PRE14, PRE18, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PRAMA10016L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 16
• Stroke MM: 406
• SubTypes: POW'R-RISER Jack Pneumatic

• Capacity Imperial Tons: 100
• Capacity KN: 889

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS60, PRU13, PRU14, PRU110, PRUS126, PRE5, PRE7, PRE9, PRE11, PRE14, PRE18, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PUD1100BK

• Type: Service Kit

• Product Group: Pumps
• Series: PU (service kit)
• SubTypes: Repair Kit

EP PUD1300B

PU Series electric over hydraulic pumps combine economy with high-performance - ideal for intermittent use when working with small to medium size cylinders and other hydraulic tools.

All models in the series are 2-speed for enhanced productivity, and each is supplied with a 10 ft (3 m) cord and control pendant for operator safety. The high-strength molded shroud with integral handle protects the motor from contamination and damage in industrial environments.

Within the PU Series is a selection of pumps that offer a choice of reservoir capacities, valve functions and voltage.

PUD1100 Series

• For advance and retract of single-acting cylinders
• For applications not requiring load holding
• Ideal for punching applications

PUD1300 Series

• Providing advance, hold, and retract of single-acting cylinders
• Ideal for applications requiring load holding
• For applications requiring solenoid valves

PUJ-Series

• Manual valves provide advance, hold, and retract operation
• 3 and 4-way valves for single or double-acting cylinders

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: PU
• SubTypes: Electric Pump - Economy

• The economic choice for small to medium sized tools.
• Lightweight, compact, and portable.
• Two-speed operation reduces cycle times for improved productivity.
• Ideal for intermittent duty cycles.
• Works well with long extension cords or generator-driven electrical power supplies.
• 115 VAC 50/60-cycle universal motor will operate under poor voltage supply.
• 24 VAC remote motor control with 10 ft (3 m) cord for operator safety.
• Starts under full load.
• High-strength shroud with integral handle protects the motor from contamination and damage.

• Spare Part(s): PUD1100BK

EP PUJ1200BK1

• Type: Service Kit

• Product Group: Pumps
• Series: PU (service kit)
• SubTypes: Repair Kit

EP PUJ1400BK

• Type: Service Kit

• Product Group: Pumps
• Series: PU (service kit)
• SubTypes: Repair Kit

EP PUJ1400B

PU Series electric over hydraulic pumps combine economy with high-performance - ideal for intermittent use when working with small to medium size cylinders and other hydraulic tools.

All models in the series are 2-speed for enhanced productivity, and each is supplied with a 10 ft (3 m) cord and control pendant for operator safety. The high-strength molded shroud with integral handle protects the motor from contamination and damage in industrial environments.

Within the PU Series is a selection of pumps that offer a choice of reservoir capacities, valve functions and voltage.

PUD1100 Series

• For advance and retract of single-acting cylinders
• For applications not requiring load holding
• Ideal for punching applications

PUD1300 Series

• Providing advance, hold, and retract of single-acting cylinders
• Ideal for applications requiring load holding
• For applications requiring solenoid valves

PUJ-Series

• Manual valves provide advance, hold, and retract operation
• 3 and 4-way valves for single or double-acting cylinders

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: PU
• SubTypes: Electric Pump - Economy

• The economic choice for small to medium sized tools.
• Lightweight, compact, and portable.
• Two-speed operation reduces cycle times for improved productivity.
• Ideal for intermittent duty cycles.
• Works well with long extension cords or generator-driven electrical power supplies.
• 115 VAC 50/60-cycle universal motor will operate under poor voltage supply.
• 24 VAC remote motor control with 10 ft (3 m) cord for operator safety.
• Starts under full load.
• High-strength shroud with integral handle protects the motor from contamination and damage.

• Spare Part(s): PUJ1400BK

EP R102

Simplex R-Series Single Acting Hydraulic Cylinders are the durable, reliable, and versatile choice for general purpose industrial use. With a vast range of cylinder tonnages and strokes available it's easy to find a cylinder perfectly matched to your application.

Threaded collars offer versatility in fixturing to give you many more application possibilities. Included inside R Series Cylinders is a positive stop to limit piston travel at the end of the stroke, adding extra strength and safety to your cylinder, and cylinder life is extended by the wiper seal.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: R
• Stroke Inches: 2.19
• Stroke MM: 55.6
• SubTypes: General Purpose Cylinder

• Capacity Imperial Tons: 10
• Capacity KN: 89,0

• Single acting with heavy-duty internal retraction spring
• Solid and plated piston resists scoring & corrosion
• Heat treated grooved saddles are provided as standard
• Stop ring limits piston travel at the end of the stroke to prevent blow-out
• High flow couplers are plated to resist corrosion
• Polyurethane wipers clean the piston surface during retraction - protecting the inner cylinder assembly from dirt, moisture, and other contaminants.
• Meets ANSI/ASME B30.1 Safety Standards
• Load tested under 125% of the nominal capacity
• For working pressures up to 10,000 psi (700 bar)

• Accessories: BA10, 18348, ATS10, BR10, BCR10, BC10

EP R515245-2

• Type: Service Kit

• SubTypes: Plug

EP RA106

• Type: Hydraulic Cylinders

• Product Group: Cylinders and Jacks

EP R57

Simplex R-Series Single Acting Hydraulic Cylinders are the durable, reliable, and versatile choice for general purpose industrial use. With a vast range of cylinder tonnages and strokes available it's easy to find a cylinder perfectly matched to your application.

Threaded collars offer versatility in fixturing to give you many more application possibilities. Included inside R Series Cylinders is a positive stop to limit piston travel at the end of the stroke, adding extra strength and safety to your cylinder, and cylinder life is extended by the wiper seal.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: R
• Stroke Inches: 7.18
• Stroke MM: 182.4
• SubTypes: General Purpose Cylinder

• Capacity Imperial Tons: 5
• Capacity KN: 44,5

• Single acting with heavy-duty internal retraction spring
• Solid and plated piston resists scoring & corrosion
• Heat treated grooved saddles are provided as standard
• Stop ring limits piston travel at the end of the stroke to prevent blow-out
• High flow couplers are plated to resist corrosion
• Polyurethane wipers clean the piston surface during retraction - protecting the inner cylinder assembly from dirt, moisture, and other contaminants.
• Meets ANSI/ASME B30.1 Safety Standards
• Load tested under 125% of the nominal capacity
• For working pressures up to 10,000 psi (700 bar)

• Accessories: 18347, BCR5, BR5

EP RAC20K50

• Type: Service Kit

• SubTypes: Repair Kit

EP RAC50K50

• Type: Service Kit

• SubTypes: Repair Kit

EP QDH120

• Type: Hydraulic Cylinders
• Max Bar: 350
• Max PSI: 5000

• Product Group: Cylinders and Jacks
• Product Line: Work Holding Tools
• Series: QDH
• Stroke Inches: 0.32
• Stroke MM: 8.1
• SubTypes: Workholding Hollow Plunger Cylinder

• Load can be attached to either end of the cylinder, providing a choice of push or pull actions - both realizing full cylinder capacity
• Very high cylinder capacities contained within small dimensions allow compact fixture designs
• Spring return operation allows for easy unloading of the workpiece
• Threaded collars and base mounting holes allow mounting flexibility, including table-top surfaces and T-slots
• Nickel-plated plungers, plunger wipers and internal venting prevent corrosion and support longer operation life on allHCS models

EP RACD3010

• Technical coating reduces wear & corrosion.
• Steel piston for protection against load damage.
• Chrome plated sleeve for extra protection.
• Stop rings for piston blow-out protection.
• Rod wiper protects inner cylinder from dirt.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: RACD
• Stroke Inches: 10
• Stroke MM: 254
• SubTypes: Aluminum Center Hole Cylinder

• Capacity Imperial Tons: 30
• Capacity KN: 266,9

EP RACD10010

• Technical coating reduces wear & corrosion.
• Steel piston for protection against load damage.
• Chrome plated sleeve for extra protection.
• Stop rings for piston blow-out protection.
• Rod wiper protects inner cylinder from dirt.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: RACD
• Stroke Inches: 10
• Stroke MM: 254
• SubTypes: Aluminum Center Hole Cylinder

• Capacity Imperial Tons: 100
• Capacity KN: 889,6

EP R59

Simplex R-Series Single Acting Hydraulic Cylinders are the durable, reliable, and versatile choice for general purpose industrial use. With a vast range of cylinder tonnages and strokes available it's easy to find a cylinder perfectly matched to your application.

Threaded collars offer versatility in fixturing to give you many more application possibilities. Included inside R Series Cylinders is a positive stop to limit piston travel at the end of the stroke, adding extra strength and safety to your cylinder, and cylinder life is extended by the wiper seal.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: R
• Stroke Inches: 9.18
• Stroke MM: 233.2
• SubTypes: General Purpose Cylinder

• Capacity Imperial Tons: 5
• Capacity KN: 44,5

• Single acting with heavy-duty internal retraction spring
• Solid and plated piston resists scoring & corrosion
• Heat treated grooved saddles are provided as standard
• Stop ring limits piston travel at the end of the stroke to prevent blow-out
• High flow couplers are plated to resist corrosion
• Polyurethane wipers clean the piston surface during retraction - protecting the inner cylinder assembly from dirt, moisture, and other contaminants.
• Meets ANSI/ASME B30.1 Safety Standards
• Load tested under 125% of the nominal capacity
• For working pressures up to 10,000 psi (700 bar)

• Accessories: 18347, BCR5, BR5

EP RACH1006005

• Type: Service Kit

• SubTypes: Tube

EP RACH1006

RACH-Series Hollow Plunger Hydraulic Cylinders (sometimes called center-hole cylinders) feature a hollow plunger with an internal thread to allow fixing to the component to be pulled. This makes them the ideal choice for when you need a lighter, more portable cylinder for applications such as tensioning, testing, pulling, and lifting. Each RACH Cylinder is rated for up to 10,000 psi (700 bar) and compliant with ASME B30.1.

Each RACH Cylinder is single-acting and uses a high-strength return spring for rapid retraction. All are equipped with bolt-on hardened steel saddles and a steel base plate for increased durability.

Aluminum is not only lightweight, but also inherently less corrosive than steel, which makes it a great material for use in many caustic environments. For enhanced protection, RACH Aluminum Cylinders are finished with an anodized hard coat finish to resist damage and extend cylinder life.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RACH
• Stroke Inches: 5.91
• Stroke MM: 150
• SubTypes: Aluminum Hollow Plunger Cylinder

• Hollow plunger design allows for both pull and push forces
• Composite bearings increase cylinder life and side load resistance
• Hard coat finish on all surfaces resists damage and extends cylinder life
• Handles included on all models
• Floating center tube increases seal life
• Steel baseplate and saddle for protection against load-induced damage
• Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
• High-strength return spring for rapid cylinder retraction
• CR400 coupler and dustcap included on all models
• All cylinders meet ASME B-30.1 standards

EP RACH1006040

• Type: Service Kit

• SubTypes: Plunger Kit