Parts

BB 250610

Overhaul Kit

BB 29-486

Tight Seal Supply Air Filter, (20 X 20 X 1)

BB 45-12140

Fluid Nozzle, 1.4Mm

CS CMM20SS-2

Check Valve, 1/4 In., S.S.

DY 56054

Muffler Insert

GG 172866

Clip, Spring

GG 19Y592

KIT, RETRO, 5-10 GA PAIL, RP MTR

Radial Piston Air Motor Retrofit Kit for 5 gallon (18 L) or 10 gallon (38 L) pail agitators. Pail cover, agitator shaft and blade not included. This kit makes it easy to replace an existing rotary vane motor on a 5 gallon (18 liter) or 10 gallon (38 L) pail agitator with a radial piston air motor. For wood (top coat, primer) and general finishing applications Radial piston air motor driven agitators are reliable, simple and cost-effective solutions for low to medium speed (<500 rpm), low to medium viscosity (<1000 cp) agitation applications. Air line lubrication not required Easy to maintain and service Sound pressure level at 70 psig (maximum recommended speed): Less than 75 dBA Pail cover, agitator shaft and blade sold separately

GG 222559

Kit, Muffler

GG 245397

KIT, ACCESSORY, PRESSURE ROLLER

EvenFlow In-Line Valve Pressure Roller Assembly Painting with a roller has never been easier. The EvenFlow Pressure Roller with In-Line Valve eliminates the need to stop and dip your roller into the messy paint tray while giving you the best angle to roll with. Includes everything you need to start rolling with an airless sprayer.

GG 24E511

KIT, MOTOR, AIR

KIT INCLUDES: MOTOR, AIR [QTY. 1], PACKING, O-RING, PTFE [QTY. 1], FITTING, ELBOW, 1/8NPT, 3/8TUBE, BRAS [QTY. 1], PLUG, PIPE [QTY. 1], TUBE, POLYURETHANE, RND [QTY. 0.7 ]

GG 286315

RAC 5 Tip, Spray

RAC 5 SwitchTip, 315 The Reverse-A-Clean (RAC) 315 RAC 5 SwitchTip is designed for narrow surfaces. The 315 SwitchTip has a 0.015 inch orifice and produces a 6 to 8 inch fan. Reverse the SwitchTip to easily clear clogs. Used for residential, commerical or industrial applicaitions. Best used with materials ranging from lacquers, latex paints and mastics. Most Widely Used Reversible Spray Tip on the Market (Black Handle)

• Used for residential and commercial applications
• Includes OneSeal for most common coatings
• Large selection of tip sizes available
• Easy to identify laser stamped tip size
• Solvent seal available when using extremely hot solvents

GG AAM517

TIP, AAM517

Graco AAM517 Fine Finish Spray Tip for G15 and G40 Guns, 0.017 inch (0.432 mm) Orifice Size, 10-12 inches (250-300 mm) Fan Width

Precision-Cut Flat Tips are designed with thinner stains and lacquers in mind to produce the best atomization for the ultimate smooth finish on furniture and similar applications.

Application: Use Graco Flat Tips where finish quality is the #1 application requirement. These tips provide an HVLP-like finish with the ability to easily adjust the fan width on the gun.

• Delivers The Softest Spray Fan
  
  • Air coming out of the cap is closer and behind the orifice of the tip
  • Zero air cap buildup
  • Better atomization
  • Softer edges and breaks up spits
• Fan Width Control
  
  • Provides application flexibility to tackle any finishing job
• Added Filtration
  
  • Includes an additional filter to reduce tip clogs

GG N65LN0

Motor, Air, 6500, Low Noise Std

IR 2115-A626

Anvil Assembly for Ingersoll Rand 2115 Series Impact Wrench

IR 2141-57

Inlet Clip Replacement Partfor Ingersoll Rand 2141 Series, 2145 Series Impact Wrench

Product Application and Uses: For use with Ingersoll Rand 2145 Series Impact Wrench

IR 2145-11

Front End Plate for Ingersoll Rand 2145 Series Impact Wrench

For Use With

• 2145QIMAX-3
• 2145QIMAX-6

IR 231-53

Rotor for Ingersoll Rand Impact Wrenches

Product Application and Uses: For use with 236G, 232, 231, 231H, and 131 Series impact wrenches

IR 2920P-465

Inlet Bushing for Ingersoll Rand 259, 261, 271, 1720P Series Impact Wrench

For Use With

• 1720P1
• 1720P3
• 259
• 261
• 261-3
• 261-6
• 271

IR 295A-TK1

Tune-up Kit for Ingersoll Rand 295 Series Impact Wrench

Includes: ‎(1) Vane pack, (3) Springs, (1) Front Rotor Bearing, (1) Rear Rotor Bearing, (1) Oil Sealing, (2) Gasket, (2) O-Ring, (1) Throttle Valve, (1) Ball

For Use With

• 295A

IR 301-22

Ball Bearing Replacement Part for Ingersoll Rand Power Tools

Product Application and Uses: For use with Ingersoll Rand 301 Series, 307 Series, 1105 Series, 3107 Series, 3101 Series, 302 Series, 308 Series Air Die Grinder and QIS Series

IR 317A-825

Backing Pad for Ingersoll Rand 317A and 317G Air Sander

For Use With

• 317A

IR 405-159

Throttle Valve Face for Ingersoll Rand Impact/Angle Wrenches

For Use With

• 231C
• 2705P1
• 2707P1
• 9RSQ83
• 9SQ83

IR H3R-31

Upper Buff Washer Set of 2 for Ingersoll Rand A, W Series Chipping Hammer

IR HHW1-213

Lower Buffer Washer Retainer Assembly Replacement Part, QTY 2 for Ingersoll Rand A & W Series Chipping Hammer

IR MG1-338

Flange Nut for Ingersoll Rand Max and M2 Series Grinder