Parts
Router Guide
DC 14-2501
DC 14-2501
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to minimum order quantities
$126.00
Guide
DC 14-2502
DC 14-2502
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to minimum order quantities
$126.00
Router Guide
DC 14-2510
DC 14-2510
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to minimum order quantities
$126.00
Router Guide
DC 14-2512
DC 14-2512
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to minimum order quantities
$126.00
Router Guide
DC 14-2539
DC 14-2539
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to Minimum Order Quantities
$171.00
Router Guide
DC 14-2542
DC 14-2542
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to Minimum Order Quantities
$179.00
Guide
DC 14-2600
DC 14-2600
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to minimum order quantities
$126.00
4in Carbide Tip Blade
DC 14-2700
DC 14-2700
BLADE CARB TIP 20TUsed on Cleco Dotco Saws
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
- Used for sawing non-metallic materials
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
$430.00
Saw Blade
DC 14-2710
DC 14-2710
BLADE CARB TIP 20TUsed on Cleco Dotco Saws
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
- Used for sawing non-metallic materials
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
$400.00
Saw Blade
DC 14-2711
DC 14-2711
BLADE CARB TIP 12TUsed on Cleco Dotco Saws
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
- Used for sawing non-metallic materials
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
$410.00
BLADE SAW, 60T
DC 14-2928
DC 14-2928
BLADE SAW, 60TUsed on Cleco Dotco Saws
- Used on Cleco Dotco Saws
$48.00