Parts
2in Saw Blade 22T
DC 14-1890
DC 14-1890
BLADE 2" SAW, 22TUsed on Cleco Dotco Saws
CAUTION: Use only for sawing non-metallic materials
- Used for sawing non-metallic materials
CAUTION: Use only for sawing non-metallic materials
$23.80
2in Saw Blade (44 Teeth)
DC 14-1891
DC 14-1891
BLADE 2" SAW, 44TUsed on Cleco Dotco Saws
CAUTION: Use only for sawing non-metallic materials
- Used for sawing non-metallic materials
CAUTION: Use only for sawing non-metallic materials
$21.80
Lock Ring
DC 14-2082
DC 14-2082
RING, LOCKFor use with Dotco 12-10, 12-20 and 12-25 series
- For use with Dotco 12-10, 12-20 and 12-25 series
$24.10
Housing
DC 14-2177
DC 14-2177
HSG ROUTER NOSEFor use with Dotco 12-10, 12-20 and 12-25 series
- For use with Dotco 12-10, 12-20 and 12-25 series
$147.00
Router Attachment
DC 14-2187
DC 14-2187
ATCH #1 ROUTERFor use with Dotco 12-10, 12-20 and 12-25 series
- For use with Dotco 12-10, 12-20 and 12-25 series
$237.00
Router Guide
DC 14-2402
DC 14-2402
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to minimum order quantities
$126.00
Router Guide
DC 14-2413
DC 14-2413
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to minimum order quantities
$126.00
Housing
DC 14-2426
DC 14-2426
HSG ROUTER NOSEFor use with Dotco 12-10, 12-20 and 12-25 series
- For use with Dotco 12-10, 12-20 and 12-25 series
$128.00
Router Attachment
DC 14-2429
DC 14-2429
ATCH ROUTERFor use with Dotco 12-10, 12-20 and 12-25 series
- For use with Dotco 12-10, 12-20 and 12-25 series
$237.00
Router Guide
DC 14-2501
DC 14-2501
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to minimum order quantities
$126.00
Guide
DC 14-2502
DC 14-2502
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to minimum order quantities
$126.00
Router Guide
DC 14-2510
DC 14-2510
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to minimum order quantities
$126.00
Router Guide
DC 14-2512
DC 14-2512
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to minimum order quantities
$126.00
Router Guide
DC 14-2539
DC 14-2539
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to Minimum Order Quantities
$171.00
Router Guide
DC 14-2542
DC 14-2542
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to Minimum Order Quantities
$179.00
Guide
DC 14-2600
DC 14-2600
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to minimum order quantities
$126.00
4in Carbide Tip Blade
DC 14-2700
DC 14-2700
BLADE CARB TIP 20TUsed on Cleco Dotco Saws
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
- Used for sawing non-metallic materials
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
$430.00
Saw Blade
DC 14-2710
DC 14-2710
BLADE CARB TIP 20TUsed on Cleco Dotco Saws
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
- Used for sawing non-metallic materials
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
$400.00
Saw Blade
DC 14-2711
DC 14-2711
BLADE CARB TIP 12TUsed on Cleco Dotco Saws
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
- Used for sawing non-metallic materials
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
$410.00
BLADE SAW, 60T
DC 14-2928
DC 14-2928
BLADE SAW, 60TUsed on Cleco Dotco Saws
- Used on Cleco Dotco Saws
$48.00