Hydraullic Units

EP LW16

Choose the LW-Series Vertical Lifting Wedge when you need to lift and lower heavy loads of up to 16-tons with a stable motion without slippage. A minimum insertion gap of 0.39" (10 mm) is needed which expands up to 2.02" (51.5 mm). Retraction force is supplied by the single-acting spring return cylinder. The maximum operating pressure is (10000 psi 700 bar).

The included SB2 stepped safety block provides reassuring support, and can also be used to increase the lifting height to 2.72" (69 mm). The LWB1 is a larger stepped block available as an option.

A compatible hydraulic pump is needed to operate the LW16. The Enerpac P392 Hand Pump, or the P392FP Foot Pump are ideal.

Alternatively, choose the LWC16 Vertical Lifting Wedge, which includes an integrated hand pump.

• Type: Spreader
• Max Bar: 700
• Max PSI: 10000

• Product Group: Flange Maintenance Tools
• Product Line: Industrial Tools
• Series: LW
• Stroke Inches: 0.83
• Stroke MM: 21
• SubTypes: Lifting Wedge

• Capacity Imperial Tons: 16
• Capacity KN: 157

EP LW-16

EP MP-110

EP MPK2

• Type: Service Kit

• SubTypes: Manifold Kit

EP MS2-10

EP MS21020

The MS21020 is our most complete maintenance set that equips you to complete a wide array of maintenance tasks. The assortment of 53 accessories enables you to quickly configure the ideal tool for just about any challenge imaginable.

This set includes three of our most popular hydraulic cylinders: The RC102, RC106, and the RC256. Using these cylinders with attachments will allow you to exert at forces up to 12.5 tons (116kN) and extend up to 6.25" (116mm) - Ideal when you need to push, pull, lift, press, straighten, spread, or clamp.

Also included is the lightweight P392 2-speed hydraulic hand pump, hose, gauge, A92 spreader attachment, lock-on or threaded connectors, and a storage crate.

Safe Operation
When using hydraulic cylinders with maintenance set attachments or components, the maximum system pressure must be limited to half of the rated pressure (5,000 psi / 350 bar). When not using attachments, the tonnage and pressure capacities are double these values.

Only use attachments provided with the set. Using non-Enerpac attachments and longer extension tubes could reduce column strength - potentially creating unsafe conditions.

• Type: Cylinder And PumpSet
• Max Bar: 350
• Max PSI: 5000

• Product Group: Cylinders and Jacks, Pumps
• Product Line: Industrial Tools
• Series: MS
• Stroke Inches: 6.25
• Stroke MM: 158
• SubTypes: Cylinder with Attachments and Hand Pump Set

• Set Includes: P392, HC7206, RC102, RC106, RC256, GP10S, GA2, A13, A28, A21, A27, A20, A595, A14, A243, A10, A8, A6, A192, A305, A18, A185, A15, A607, A129, A128, A132, A238, A5, A141, A218, A19, A242, A92, A16, MZ1050, MZ1051, MZ1052, A285, MZ1002, MZ1003, A239, MZ1004, A240, MZ1005, A241, CW350

EP MS220

This hydraulic pump and cylinder set includes a complete assortment of accessories allowing you to quickly configure a unique tool to solve your many difficult maintenance tasks.

The set includes the RC256 Hydraulic Cylinder, which when used with attachments allows you to exert a force of 12.5 tons (116kN) and a stroke of 6.25" (116mm). Ideal when you need to push, pull, lift, press, straighten, or clamp.

Also included is the lightweight P392 2-speed hydraulic hand pump, hose, gauge, lock-on or threaded connectors, and a storage crate.

Safe Operation
When using hydraulic cylinders with maintenance set attachments or components, the maximum system pressure must be limited to half of the rated pressure (5,000 psi / 350 bar). When not using attachments, the tonnage and pressure capacities are double these values.

Only use attachments provided with the set. Using non-Enerpac attachments and longer extension tubes could reduce column strength - potentially creating unsafe conditions.

• Type: Cylinder And PumpSet
• Max Bar: 350
• Max PSI: 5000

• Product Group: Cylinders and Jacks, Pumps
• Product Line: Industrial Tools
• Series: MS
• Stroke Inches: 6.25
• Stroke MM: 158
• SubTypes: Cylinder with Attachments and Hand Pump Set

• Set Includes: P392, HC7206, RC256, GP10S, GA2, A28, A27, A595, A243, A607, A238, A218, A242, A239, A240, A241, CW166

EP MVPM5

• Type: Valve
• Max Bar: 350
• Max PSI: 5000

• Product Group: Valves, Pumps
• Product Line: Work Holding Tools
• Series: MVP
• SubTypes: Sequence Valve

• Sequence valves block the oil to a secondary hydraulic circuit until pressure in the primary circuit reaches a preset level. The sequence valves have a built-in check system to allow the oil to flow back without external piping.
• Direct accurate pressure setting
• Pressure setting between 500-5000 psi for secondary circuit is secured with lock nut
• Manifold mounting ports on MVPM5
• Manifold O-rings included with MVPM5

EP MZ-1003

EP MZ-1004

EP MZ-1005

EP MZ-1051

EP NC2432

NC-Series Hydraulic Nut Splitters use a single blade configuration suited to general nut cutting applications across a wide range of industries.

The heat-treated steel blade with its optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NC-Series Nut Cutters are compact, simple, and easy to use. The ergonomic design ensures comfortable use, thanks to the carefully considered angled head design and handle position.

Nuts are often difficult to remove, and while loosening them using tightening tools is possible, this generally requires larger equipment and takes more time.

Using a cutting torch or a hammer and chisel presents safety risks and can cause damage to the joint components. They also involve significantly longer setup and operational time.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NC
• SubTypes: Nut Cutter

• bundleSet_IDs: NCB2432
• Capacity Imperial Tons: 15
• Capacity KN: 147

• Compact and ergonomic design, easy to use
• Unique angled head design
• Single-acting, spring return cylinder
• Heavy duty chisels can be reground
• Nut Splitters include spare chisel, spare set screw and wrench used to secure the chisel. A CR-400 coupler is standard.
• For applications with bolt sizes that are common to two tool model sizes, we recommend to select the larger of the two tools for the best results.
• These are not suited for square, star, round or stainless steel nuts. Maximum allowable hardness of nuts to be split is HRc-44.
• For materials and sizes not specified, contact Enerpac Technical Services.

• Accessories: NCB2432

EP NC3241

NC-Series Hydraulic Nut Splitters use a single blade configuration suited to general nut cutting applications across a wide range of industries.

The heat-treated steel blade with its optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NC-Series Nut Cutters are compact, simple, and easy to use. The ergonomic design ensures comfortable use, thanks to the carefully considered angled head design and handle position.

Nuts are often difficult to remove, and while loosening them using tightening tools is possible, this generally requires larger equipment and takes more time.

Using a cutting torch or a hammer and chisel presents safety risks and can cause damage to the joint components. They also involve significantly longer setup and operational time.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NC
• SubTypes: Nut Cutter

• Capacity Imperial Tons: 20
• Capacity KN: 196

• Compact and ergonomic design, easy to use
• Unique angled head design
• Single-acting, spring return cylinder
• Heavy duty chisels can be reground
• Nut Splitters include spare chisel, spare set screw and wrench used to secure the chisel. A CR-400 coupler is standard.
• For applications with bolt sizes that are common to two tool model sizes, we recommend to select the larger of the two tools for the best results.
• These are not suited for square, star, round or stainless steel nuts. Maximum allowable hardness of nuts to be split is HRc-44.
• For materials and sizes not specified, contact Enerpac Technical Services.

• Accessories: NCB3241

EP NC4150

NC-Series Hydraulic Nut Splitters use a single blade configuration suited to general nut cutting applications across a wide range of industries.

The heat-treated steel blade with its optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NC-Series Nut Cutters are compact, simple, and easy to use. The ergonomic design ensures comfortable use, thanks to the carefully considered angled head design and handle position.

Nuts are often difficult to remove, and while loosening them using tightening tools is possible, this generally requires larger equipment and takes more time.

Using a cutting torch or a hammer and chisel presents safety risks and can cause damage to the joint components. They also involve significantly longer setup and operational time.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NC
• SubTypes: Nut Cutter

• bundleSet_IDs: NCB4150
• Capacity Imperial Tons: 35
• Capacity KN: 343

• Compact and ergonomic design, easy to use
• Unique angled head design
• Single-acting, spring return cylinder
• Heavy duty chisels can be reground
• Nut Splitters include spare chisel, spare set screw and wrench used to secure the chisel. A CR-400 coupler is standard.
• For applications with bolt sizes that are common to two tool model sizes, we recommend to select the larger of the two tools for the best results.
• These are not suited for square, star, round or stainless steel nuts. Maximum allowable hardness of nuts to be split is HRc-44.
• For materials and sizes not specified, contact Enerpac Technical Services.

• Accessories: NCB4150

EP NC6075

NC-Series Hydraulic Nut Splitters use a single blade configuration suited to general nut cutting applications across a wide range of industries.

The heat-treated steel blade with its optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NC-Series Nut Cutters are compact, simple, and easy to use. The ergonomic design ensures comfortable use, thanks to the carefully considered angled head design and handle position.

Nuts are often difficult to remove, and while loosening them using tightening tools is possible, this generally requires larger equipment and takes more time.

Using a cutting torch or a hammer and chisel presents safety risks and can cause damage to the joint components. They also involve significantly longer setup and operational time.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NC
• SubTypes: Nut Cutter

• Capacity Imperial Tons: 90
• Capacity KN: 882

• Compact and ergonomic design, easy to use
• Unique angled head design
• Single-acting, spring return cylinder
• Heavy duty chisels can be reground
• Nut Splitters include spare chisel, spare set screw and wrench used to secure the chisel. A CR-400 coupler is standard.
• For applications with bolt sizes that are common to two tool model sizes, we recommend to select the larger of the two tools for the best results.
• These are not suited for square, star, round or stainless steel nuts. Maximum allowable hardness of nuts to be split is HRc-44.
• For materials and sizes not specified, contact Enerpac Technical Services.

• Accessories: NCB6075

EP P142ALSS

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P
• SubTypes: Hand Pump - Two Speed

• Corrosion resistant, nickel-plated valves and cylinders
• Stainless steel pump inserts will not corrode
• Viton Seals provide heat and chemical resistance
• Anodized aluminum pump reservoirs and plastic encapsulated pump bodies resist wet environments
• Two-speed operation reduces pump handle strokes 78% compared to single-speed pumps
• Pump handles lock for easy carrying

• Spare Part(s): DA8802900SR, P142ALSSK

EP P143

EP P-18

EP P181190W

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Relief Valve

EP P20857

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Crosspin

EP P-2282

EP P25

These Low-Pressure Hydraulic Hand Pumps are durable, portable, highly efficient, and easy to use. Each model in the series features an all-steel construction, a chrome plated plunger, and a wiper system for long-lasting performance.

These pumps are constructed to power a wide range of single acting cylinders and tools in space restricted areas. The range includes the P51 that can be operated in the horizontal orientation only, and others also capable of operating in the vertical orientations: P18 with the pump head facing down, P25, P50 with the pump head facing up. Each is protected by external load-release valves and internal overload pressure-relief valves.

With a choice of oil capacities up to 200 in3 (3,277 cm3), and operating pressures of 2,500 psi (175 bar) - 5,000 psi (350 bar) you will find an Enerpac Low Pressure Hydraulic Hand Pump to suit your needs.

• Type: Hydraulic Pump
• Max Bar: 175
• Max PSI: 2500

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P
• SubTypes: Hand Pump - Single Speed

• P25 and P50 pumps oil in both forward and reverse handle movement improving overall efficiency, ideal when mounting space is restricted
• External load-release valve
• Internal pressure-relief valve for overload protection
• P25 and P50 vertical operation requires pump vent side facing up

• Spare Part(s): CA365024SR, P181190W, P50K1

EP P301D

• Heavy duty, metal construction for durability.
• High displacements of oil per stroke.
• Low, back saving handle effort.
• Large reservoir capacities.

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: P Steel
• SubTypes: Hand Pump - Heavy Duty Steel

EP P-392FP