GRACO INC. S10595

GRACO INC. S10595 branded products

View as Grid List

Sort by

KIT, PUMP LOWER, PRO-CONNECT, CS, W/O BUNG ADAPTER

GG 273295

KIT, PUMP LOWER, PRO-CONNECT, CS, W/O BUNG ADAPTER

Graco 273295 Pump Lower, Kit, (Carbon Steel)

Transfer Pumps are required to move A and B materials to the Reactor® Spray Systems. The T4 Transfer Pump combines Graco’s proven Merkur® air-motor and carbon steel lower. The T4 is a 3:1 ratio pump with ProConnect technology – allowing you to quickly connect and disconnect the air motor from the pump lower.

Quick Transfer Between Drums – quickly change to a new drum of material without the mess of dripping chemical by using multiple pump lowers.
Easier to Maneuver – easily transfer the T4 pump between drums by quickly disconnecting the air motor from the lower before transferring. This makes the pump lighter weight and reduces the necessary ceiling height of your rig.
Eliminate Downtime – get up and running quickly when your pump lower requires maintenance by having a spare pump lower that can easily be installed.

Model: Pump Lower

Material: Carbon Steel
Package Options: Bare

$1,155.00

Stud

GG 27420-2-160

Stud

$2,740.00

SHAFT COUPLER 3/4-16 THD

GG 27421

SHAFT COUPLER 3/4-16 THD

$2,640.00

Clamp

GG 276025

Clamp

$65.25

Seal Cup, Air Valve

GG 276733

Seal Cup, Air Valve

$114.00

Tool Wrench

GG 276741

Tool Wrench

$112.00

Needle, Electrode

GG 277007

Needle, Electrode

$132.00

Kit, Repair, Pump 5900

GG 277070

Kit, Repair, Pump 5900

$1,095.00

Kit, Hose, 1/4" X 50'

GG 277241

Kit, Hose, 1/4" X 50'

$101.00

HOSE, CPLD, 1/4" X 3', 4000 WPR

GG 277249

HOSE, CPLD, 1/4" X 3', 4000 WPR

Graco 277249 BlueMax II HP Airless Whip Hose, 1/4 in x 3 ft (0.9 m), 4000 psi

The BlueMax II HP Whip Hose provides more flexibility and increased operator control at the gun. This BlueMax II Whip Hose has a 1/4 inch diameter and is 3 feet long and rated for up to 4000 psi.

Application: For high-pressure spraying applications

Lighter Weight
Over 10% lighter weight and increased hose flexibility improves under pressure
Highest Safety Standards
Conductive core meets the highest worldwide safety standards unlike competitive ground wire hose designs
Minimal Hose Coil Memory
BlueMax II Hose has superior flexibility and reduced coil memory providing ease of use during coiling and uncoiling

Model: BlueMax II
Series: Whip Hose

Hose Diameter (in): 1/4
Hose Length (ft): 3
Hose Length (m): 0.9150
Maximum Working Pressure (bar): 280
Maximum Working Pressure (kPa): 2800
Maximum Working Pressure (psi): 4000

$44.90

HOSE, CPLD, 1/4" X 50', 4000WPR

GG 277250

HOSE, CPLD, 1/4" X 50', 4000WPR

Graco 277250 BlueMax II HP Airless Hose, 1/4 in x 50 ft, 4000 psi

To maximize performance, choose BlueMax II high performance airless hose rated up to 4000 psi. With superior flexibility and durability, BlueMax II is designed to ensure you get the best results from your airless sprayer.

Lighter Weight
Over 10% lighter weight and increased hose flexibility improves usability while spraying under pressure
Highest Safety Standards
Conductive core meets the highest worldwide safety standards unlike competitive ground wire hose designs
Minimal Hose Coil Memory
BlueMax II Hose has superior flexibility and reduced coil memory providing ease of use during coiling and uncoiling

Model: BlueMax II
Series: Hose

Connection Type: FBE
Hose Diameter (in): 1/4
Hose Length (cm): 1524
Hose Length (ft): 50
Hose Length (in): 600
Hose Length (m): 15.2
Hose Length (mm): 15200
Inside Diameter (cm): 0.635
Inside Diameter (in): 1/4
Inside Diameter (mm): 6.35
Material: Nylon
Maximum Working Pressure (bar): 276
Maximum Working Pressure (kPa): 27600
Maximum Working Pressure (MPa): 27.6
Maximum Working Pressure (psi): 4000

$219.00

HOSE, CPLD, 3/8" X 50', 4000 WPR

GG 277251

HOSE, CPLD, 3/8" X 50', 4000 WPR

Graco 277251 BlueMax II HP Airless Hose, 3/8 in x 50 ft, 4000 psi

Lighter Weight
Over 10% lighter weight and increased hose flexibility improves usability while spraying under pressure
Highest Safety Standards
Conductive core meets the highest worldwide safety standards unlike competitive ground wire hose designs
Minimal Hose Coil Memory
BlueMax II Hose has superior flexibility and reduced coil memory providing ease of use during coiling and uncoiling

Model: BlueMax II
Series: Hose

Connection Type: FBE
Hose Diameter (in): 3/8
Hose Length (cm): 1524
Hose Length (ft): 50
Hose Length (in): 600
Hose Length (m): 15
Hose Length (mm): 15200
Inside Diameter (cm): 0.9525
Inside Diameter (in): 3/8
Inside Diameter (mm): 9.525
Material: Nylon
Maximum Working Pressure (bar): 276
Maximum Working Pressure (kPa): 27600
Maximum Working Pressure (MPa): 27.6
Maximum Working Pressure (psi): 4000

$308.00

HOSE, CPLD, 1/2"X50', 4000WPR

GG 277253

HOSE, CPLD, 1/2"X50', 4000WPR

BlueMax II HP Airless Hose, 1/2 in x 50 ft, 4000 psi To maximize performance, choose BlueMax II high performance airless hose rated up to 4000 psi. With superior flexibility and durability, BlueMax II is designed to ensure you get the best results from your airless sprayer. Lighter Weight

Over 10% lighter weight and increased hose flexibility improves under pressure

Highest Safety Standards

Conductive core meets the highest worldwide safety standards unlike competitive ground wire hose designs

Minimal Hose Coil Memory

BlueMax II Hose has superior flexibility and reduced coil memory providing ease of use during coiling and uncoiling

Corrosion Resistant

Plated spring guards are more corrosion resistant

$460.00

Kit, Repair, B Cartridge

GG 277296

Kit, Repair, B Cartridge

$145.50

Kit, Repair

GG 273026

KIT, REPAIR

Graco 273026 Coupling Jaw Repair Kit for High-Flo Lowers

$841.00

Kit, Needle, Electrode

GG 276697

KIT, NEEDLE, ELECTRODE

Graco 276697 SnapBack Electrode Replacement Needle

$113.00

Spacer

GG 276049

SPACER

Graco 276049 5 Gallon Platens Spacer

Compatible Material: Waterborne

$95.75

Kit, Nozzle, 1.80 mm , Xp, Brown

GG 25N897

KIT,NOZZLE,1.80MM,XP,BROWN

$137.50

Kit, Valve, Quick Adjust, Xp

GG 25N919

Kit, Valve, Quick Adjust, Xp

$314.00

Kit, Sanitary Gasket-K1 Ep-4

GG 25P064

KIT, SANITARY GASKET-K1 EP-4

Graco 25P064 EPDM Seal Kit for 3-inch Flapper Pump

$130.00

Kit, Gasket, Air Cover

GG 25P114

Kit, Gasket, Air Cover

$133.00

Kit, Ram, Conv, D60, Sm, Relief

GG 25P280

Kit, Ram, Conv, D60, Sm, Relief

$24,880.00

GT 750 PUMP, TOPPER

GG 25P544

GT 750 PUMP, TOPPER

Graco 25P544 GT 750 36:1 Grease Transfer Topper-Inductor Package for 400 lb (180 kg) drums

The GT 750 36:1 pump was engineered for efficient grease transfer in demanding applications. The Topper-Inductor package allows for quick drum changes and reduces strain on operators.

Call for pricing

KIT, DIAPHRAGM-H1 EO

GG 25P270

KIT, DIAPHRAGM-H1 EO

EPDM Overmold Diaphragm Kit for 2- to 4-inch Pump

$1,610.00

FUSION PC GUN, RND, 01

GG 25P588

FUSION PC GUN, RND, 01

Fusion ProConnect Gun with Round 01 Mix Chamber and 0.042 in (1.06 mm) Orifice Size A perfect rebuild in seconds is now possible with the revolutionary Fusion PC (ProConnect) gun, featuring an all-in-one cartridge head that replaces multiple individual parts of the fluid section with a single component. Simply replacing the cartridge completely eliminates the need for a time-consuming traditional rebuild, keeping you spraying and minimizing costly downtime. Unlike any other spray foam gun available A single cartridge replaces the entire fluid section in seconds Built on top of the time-tested Fusion Air Purge platform, the PC gun sprays exactly like a Fusion AP Integrated check valves for cross-over containment 13 parts are replaced by a single ProConnect cartridge Eliminates the need to purchase fluid section o-rings Spare ProConnect cartridges can replace your back-up guns Retrofit Kit available to convert existing Fusion AP guns

$3,870.00

KIT, DIAPHRAGM-F1 PO

GG 25P208

KIT, DIAPHRAGM-F1 PO

PTFE/EPDM Overmold Diaphragm Kit for 1.5-inch Pump

$1,485.00

FUSION PC GUN, RND, 02

GG 25P589

FUSION PC GUN, RND, 02

Graco 25P589 Fusion ProConnect Gun with Round 02 Mix Chamber and 0.052 in (1.3 mm) Orifice Size

A perfect rebuild in seconds is now possible with the revolutionary Fusion PC (ProConnect) gun, featuring an all-in-one cartridge head that replaces multiple individual parts of the fluid section with a single component. Simply replacing the cartridge completely eliminates the need for a time-consuming traditional rebuild, keeping you spraying and minimizing costly downtime.

Application: Unlike any other spray foam gun available

A single cartridge replaces the entire fluid section in seconds
Built on top of the time-tested Fusion Air Purge platform, the PC gun sprays exactly like a Fusion AP
Integrated check valves for cross-over containment
Eliminates the need to purchase fluid section o-rings
Spare ProConnect cartridges can replace your back-up guns
Retrofit Kit available to convert existing Fusion AP guns

Model: Fusion PC
Series: Round

Air Inlet Size (cm): 0.635
Air Inlet Size (in): 1/4
Air Inlet Size (mm): 6.35
Air Inlet Thread Type: NPT
Applicator Type: Manual
Compatible Material: Adhesives, Polyurethane, Polyurea, Polyurethane Coating, Spray Polyurethane Foam
Component A Inlet Size (cm): 1.27
Component A Inlet Size (in): 1/2-20
Component A Inlet Size (mm): 12.7
Component A Inlet Thread Type: UNF
Component B Inlet Size (cm): 1.42875
Component B Inlet Size (in): 9/16-18
Component B Inlet Size (mm): 14.2875
Component B Inlet Thread Type: UNF
Component Type: Plural-Component
Fluid Orifice Size (cm): 0.107
Fluid Orifice Size (in): .052
Fluid Orifice Size (mm): 1.07
For Use With: Non-Flammable Foam and Polyurea
Gun Activation: Manual
Gun Included: 1
Gun Type: Air Purge Gun
Gun Weight (g): 1338
Gun Weight (kg): 1.3
Gun Weight (lb): 2.95
Gun Weight (oz): 47
Impingement Port Size (in): 0.052
Impingement Port Size (mm): 1.32
Includes: PC52RD Mix Chamber Tip
Maximum Air Inlet Pressure (bar): 9
Maximum Air Inlet Pressure (kPa): 900
Maximum Air Inlet Pressure (MPa): 0.9
Maximum Air Inlet Pressure (psi): 130
Maximum Air Pressure (bar): 9
Maximum Air Pressure (kPa): 900
Maximum Air Pressure (MPa): 0.9
Maximum Air Pressure (psi): 130
Maximum Flow Rate @ PSI (lb/min): 50
Maximum Fluid Pressure (bar): 241
Maximum Fluid Pressure (kPa): 24100
Maximum Fluid Pressure (MPa): 24.1
Maximum Fluid Pressure (psi): 3500
Maximum Fluid Temperature (°C): 93
Maximum Fluid Temperature (°F): 200
Maximum Fluid Pressure (bar): 241
Maximum Fluid Pressure (kPa): 24100
Maximum Fluid Pressure (MPa): 24.1
Maximum Fluid Pressure (psi): 3500
Maximum Fluid Temperature (°C): 93
Maximum Fluid Temperature (°F): 200
Maximum Fluid Working Pressure (bar): 245
Maximum Fluid Working Pressure (MPa): 24.5
<

$3,870.00

Kit, Tools, Fusion Pc

GG 25P660

Kit, Tools, Fusion Pc

$36.10

KIT, FUSION PC, RETRO, BARE

GG 25P704

KIT, FUSION PC, RETRO, BARE

Fusion ProConnect Retrofit Kit without Mix Chamber Transform your Fusion Air Purge gun into a Fusion PC with the ProConnect Retrofit Kit, allowing you to take full advantage of what the Fusion PC delivers: A perfect rebuild in seconds. The Retrofit Kit is compatible with all Fusion AP guns and can be combined with any Fusion PC mix chamber (sold separately). Acquire all the advantages of the revolutionary Fusion ProConnect while utilizing your existing Fusion AP handle and fluid manifold. Same Fusion AP gun, all new possibilities A single cartridge replaces the entire fluid section in seconds Sprays exactly like a Fusion AP Integrated check valves for cross-over containment 13 parts are replaced by a single ProConnect cartridge Eliminates the need to purchase fluid section o-rings Spare ProConnect cartridges can replace your back-up guns

$1,275.00

KIT, AIR MOTOR BEARING, REBUILD

GG 25P720

KIT, AIR MOTOR BEARING, REBUILD

Radial Piston Air Motor Bearing Rebuild Kit

$183.50

KIT, FUSION PC, RETRO, RND, 01

GG 25P701

KIT, FUSION PC, RETRO, RND, 01

Fusion ProConnect Retrofit Kit with Round 01 Mix Chamber and 0.042 in (1.06 mm) Orifice Size Transform your Fusion Air Purge gun into a Fusion PC with the ProConnect Retrofit Kit, allowing you to take full advantage of what the Fusion PC delivers: A perfect rebuild in seconds. The Retrofit Kit is compatible with all Fusion AP guns and is available in multiple mix chamber sizes. Acquire all the advantages of the revolutionary Fusion ProConnect while utilizing your existing Fusion AP handle and fluid manifold. Same Fusion AP gun, all new possibilities A single cartridge replaces the entire fluid section in seconds Sprays exactly like a Fusion AP Integrated check valves for cross-over containment 13 parts are replaced by a single ProConnect cartridge Eliminates the need to purchase fluid section o-rings Spare ProConnect cartridges can replace your back-up guns

$1,615.00

5/10 Gallon Pail Agitator Shaft Coupler 1/2"-3/8"

GG 25P709

5/10 Gallon Pail Agitator Shaft Coupler 1/2"-3/8"

Call for pricing

KIT, AIR MOTOR PISTON, REBUILD

GG 25P721

KIT, AIR MOTOR PISTON, REBUILD

Radial Piston Air Motor Piston Rebuild Kit

$267.00

REACTOR HEATED HOSE, WHIP, 1/4ID, 2000PSI, 10FT

GG 25P770

REACTOR HEATED HOSE, WHIP, 1/4ID, 2000PSI, 10FT

10 ft x 1/4 in High Flex Whip Hose, 2000 psi, Without Cable, Xtreme-Wrap, Reactor 1 & 2 The whip hose is designed to be lighter weight and offers improved flexibility using materials that are more durable and have higher temperature ratings.This whip hose also includes the newest electrical configuration that removes all electrical connections from near the gun. For use with Reactor 2 internally heated hose. Light Weight Design

20% lighter weight than traditional whip hose

Stainless Steel Braiding High Temperature Hose Core and Silicone Wire Protection Compatible With All Reactor and Reactor 2 Hoses and Systems Includes reliable Xtreme Wrap scuff guard

$1,205.00

Reactor Heated Hose, Whip, 1/4ID, 2000PSI, 20FT

GG 25P771

Reactor Heated Hose, Whip, 1/4ID, 2000PSI, 20FT

Graco 25P771 20 ft x 1/4 in High Flex Whip Hose, 2000 psi, Without Cable, Xtreme-Wrap, Reactor 1 & 2

The whip hose is designed to be lighter weight and offers improved flexibility using materials that are more durable and have higher temperature ratings.This whip hose also includes the newest electrical configuration that removes all electrical connections from near the gun.

Application: For use with Reactor 2 internally heated hose.

Light Weight Design
20% lighter weight than traditional whip hose
Stainless Steel Braiding
High Temperature Hose Core and Silicone Wire Protection
Includes reliable Xtreme Wrap scuff guard

Model: Reactor 1
Series: Xtreme Wrap

Compatible Sprayer: Reactor 1 & 2
Connection Type: Male x Female
Hose Diameter (in): 1/4"
Hose Diameter (mm): 6.35
Hose Heating Type: External Heated
Hose Length (ft): 20
Hose Length (m): 6
Inside Diameter (in): 1/4
Material: PTFE
Maximum Temperature (°C): 82
Maximum Temperature (°F): 180
Maximum Working Pressure (bar): 138
Maximum Working Pressure (MPa): 13.8
Maximum Working Pressure (psi): 2000

$1,345.00

Reactor Heated Hose, Whip, 1/4ID, 3500PSI, 10ft

GG 25P772

Reactor Heated Hose, Whip, 1/4ID, 3500PSI, 10ft

Graco 25P772 10 ft x 1/4 in High Flex Whip Hose, 3500 psi, Without Cable, Xtreme-Wrap, Reactor 1 & 2

Graco’s Improved Flex heated hoses are designed specifically for use with Reactor Equipment. Hoses are a key component to the total system, making it important to achieve accurate and uniform heating for the best application possible.

Application: For Reactor proportioners.

Improved Flex design, making it easier to spray in tight areas
20% Lighter than previous whip hose
Includes 18&Prime, of insulated, non-heated section near gun
Includes reliable Xtreme Wrap scuff guard

Model: Reactor 1
Series: Xtreme Wrap

Compatible Sprayer: Reactor 1 & 2
Connection Type: Male x Female
Hose Diameter (in): 1/4"
Hose Diameter (mm): 6.35
Hose Heating Type: External Heated
Hose Length (ft): 10
Hose Length (m): 3
Inside Diameter (in): 0.25
Material: PTFE
Maximum Temperature (°C): 82
Maximum Temperature (°F): 180
Maximum Working Pressure (bar): 241
Maximum Working Pressure (MPa): 24.1
Maximum Working Pressure (psi): 3500

$1,340.00

KIT, VALVE, FLAPPER, 4"

GG 25P086

KIT, VALVE, FLAPPER, 4"

4-inch 316 SST Flapper Valve Check Kit

$777.00

Kit, Gasket, Barrel

GG 25N921

Kit, Gasket, Barrel

$31.40

Kit, O-Rings, Fluid, Fusion Pc

GG 25P851

Kit, O-Rings, Fluid, Fusion Pc

$53.50

REACTOR HEATED HOSE, WHIP, 1/4ID, 3500PSI, 20FT

GG 25P773

REACTOR HEATED HOSE, WHIP, 1/4ID, 3500PSI, 20FT

Graco 25P773 20 ft x 1/4 in High Flex Whip Hose, 3500 psi, Without Cable, Xtreme-Wrap, Reactor 1 & 2

Application: For Reactor proportioners.

Improved Flex design, making it easier to spray in tight areas
20% Lighter than previous whip hose
Includes 18&Prime, of insulated, non-heated section near gun
Includes reliable Xtreme Wrap scuff guard

Model: Reactor 1
Series: Xtreme Wrap

Compatible Sprayer: Reactor 1 & 2
Connection Type: Male x Female
Hose Diameter (in): 1/4"
Hose Diameter (mm): 6.35
Hose Heating Type: External Heated
Hose Length (ft): 20
Hose Length (m): 6
Inside Diameter (in): 0.25
Material: PTFE
Maximum Temperature (°C): 82
Maximum Temperature (°F): 180
Maximum Working Pressure (bar): 241
Maximum Working Pressure (MPa): 24.1
Maximum Working Pressure (psi): 3500

$2,020.00

Hose, Bundle, E-10HP, 35Ft

GG 25R000

Hose, Bundle, E-10HP, 35Ft

$1,485.00

Kit, O-Ring, Air, Fusion Pc

GG 25P850

Kit, O-Ring, Air, Fusion Pc

$41.70

KIT, AIR MOTOR ENDCAP, REBUILD

GG 25P860

KIT, AIR MOTOR ENDCAP, REBUILD

Radial Piston Air Motor End Cap

$108.50

Hose, Fluid, As, Wb, Shielded, 25

GG 25R002

Hose, Fluid, As, Wb, Shielded, 25

$2,020.00

Hose, Fluid, Wb, Aa, 25 ft

GG 25R012

Hose, Fluid, Wb, Aa, 25 ft

$3,310.00

KIT, FUSION PC, RETRO, RND, 00-01

GG 25R087

KIT, FUSION PC, RETRO, RND, 00-01

Graco 25R087 Fusion ProConnect Retrofit Kit with Round 00-01 Mix Chamber and 0.037 in (0.94 mm) Orifice Size

Transform your Fusion Air Purge gun into a Fusion PC with the ProConnect Retrofit Kit, allowing you to take full advantage of what the Fusion PC delivers: A perfect rebuild in seconds. The Retrofit Kit is compatible with all Fusion AP guns and is available in multiple mix chamber sizes. Acquire all the advantages of the revolutionary Fusion ProConnect while leveraging your existing Fusion AP handle and fluid manifold.

Application: Same Fusion AP gun, all new possibilities

A single cartridge replaces the entire fluid section in seconds
Sprays exactly like a Fusion AP
Integrated check valves for cross-over containment
Eliminates the need to purchase fluid section o-rings
Spare ProConnect cartridges can replace your back-up guns

Model: Fusion PC
Series: Round

Includes: PC37RD Mix Chamber Tip
Mix Chamber: 00-01 (.037)

$1,615.00

KIT, SDU, SEAL INFL FDA NEO

GG 25P317

KIT, SDU, SEAL INFL FDA NEO

Inflatable Drum Plate Replacement Seal Kit, Neoprene

$2,290.00

FUSION PC GUN, RND, 00-01

GG 25R084

FUSION PC GUN, RND, 00-01

Graco 25R084 Fusion ProConnect Gun with Round 00-01 Mix Chamber and 0.037 in (0.94 mm) Orifice Size

Application: Unlike any other spray foam gun available

A single cartridge replaces the entire fluid section in seconds
Built on top of the time-tested Fusion AP platform, the PC gun sprays exactly like a Fusion AP
Integrated check valves for cross-over containment
Eliminates the need to purchase fluid section o-rings
Spare ProConnect cartridges can replace your back-up guns
Retrofit Kit available to convert existing Fusion AP guns

Model: Fusion PC
Series: Round

Air Inlet Size (cm): 0.635
Air Inlet Size (in): 1/4
Air Inlet Size (mm): 6.35
Air Inlet Thread Type: NPT
Applicator Type: Manual
Compatible Material: Adhesives, Polyurethane, Polyurea, Polyurethane Coating, Spray Polyurethane Foam
Component A Inlet Size (cm): 1.27
Component A Inlet Size (in): 1/2-20
Component A Inlet Size (mm): 12.7
Component A Inlet Thread Type: UNF
Component B Inlet Size (cm): 1.42875
Component B Inlet Size (in): 9/16-18
Component B Inlet Size (mm): 14.2875
Component B Inlet Thread Type: UNF
Component Type: Plural-Component
Fluid Orifice Size (cm): 0.107
Fluid Orifice Size (in): .037
Fluid Orifice Size (mm): 1.07
For Use With: Non-Flammable Foam and Polyurea
Gun Activation: Manual
Gun Included: 1
Gun Type: Air Purge Gun
Gun Weight (g): 1338
Gun Weight (kg): 1.3
Gun Weight (lb): 2.95
Gun Weight (oz): 47
Impingement Port Size (in): 0.037
Impingement Port Size (mm): 0.94
Includes: PC37RD Mix Chamber Tip
Maximum Air Inlet Pressure (bar): 9
Maximum Air Inlet Pressure (kPa): 900
Maximum Air Inlet Pressure (MPa): 0.9
Maximum Air Inlet Pressure (psi): 130
Maximum Air Pressure (bar): 9
Maximum Air Pressure (kPa): 900
Maximum Air Pressure (MPa): 0.9
Maximum Air Pressure (psi): 130
Maximum Flow Rate @ PSI (lb/min): 50
Maximum Fluid Pressure (bar): 241
Maximum Fluid Pressure (kPa): 24100
Maximum Fluid Pressure (MPa): 24.1
Maximum Fluid Pressure (psi): 3500
Maximum Fluid Temperature (°C): 93
Maximum Fluid Temperature (°F): 200
Maximum Fluid Pressure (bar): 241
Maximum Fluid Pressure (kPa): 24100
Maximum Fluid Pressure (MPa): 24.1
Maximum Fluid Pressure (psi): 3500
Maximum Fluid Temperature (°C): 93
Maximum Fluid Temperature (°F): 200
Maximum Fluid Working Pressure (bar): 245
Maximum Fluid Working Pressure (MPa): 24.5
<

$3,870.00

Fusion ProConnect Gun with Route 03 Mix Chamber

GG 25R085

Fusion ProConnect Gun with Route 03 Mix Chamber

$3,870.00

KIT, FUSION PC, RETRO, FL, 00, 438

GG 25R089

KIT, FUSION PC, RETRO, FL, 00, 438

Graco 25R089 Fusion ProConnect Retrofit Kit with Flat 00 Mix Chamber and 0.029 in (0.74 mm) Orifice Size

Application: Same Fusion AP gun, all new possibilities

A single cartridge replaces the entire fluid section in seconds
Sprays exactly like a Fusion AP
Integrated check valves for cross-over containment
Eliminates the need to purchase fluid section o-rings
Spare ProConnect cartridges can replace your back-up guns

Model: Fusion PC
Series: Flat

Includes: PC29RD Mix Chamber Tip
Mix Chamber: 00 (.029)

$1,615.00

KIT, FUSION PC, RETRO, RND, 03

GG 25R088

KIT, FUSION PC, RETRO, RND, 03

Fusion ProConnect Retrofit Kit Round 03 Mix Chamber and 0.060 in (1.5 mm) Orifice Size Transform your Fusion Air Purge gun into a Fusion PC with the ProConnect Retrofit Kit, allowing you to take full advantage of what the Fusion PC delivers: A perfect rebuild in seconds. The Retrofit Kit is compatible with all Fusion AP guns and is available in multiple mix chamber sizes. Acquire all the advantages of the revolutionary Fusion ProConnect while leveraging your existing Fusion AP handle and fluid manifold. Same Fusion AP gun, all new possibilities A single cartridge replaces the entire fluid section in seconds Sprays exactly like a Fusion AP Integrated check valves for cross-over containment 13 parts are replaced by a single ProConnect cartridge Eliminates the need to purchase fluid section o-rings Spare ProConnect cartridges can replace your back-up guns

$1,615.00

REGULATOR, BP, AIRPILOT, HIGH-FLOW

GG 25R457

REGULATOR, BP, AIRPILOT, HIGH-FLOW

Graco 25R457 Low Shear Fluid Back Pressure Regulator, 300 Max psi, 25 gpm Max flow rate, SST, Pneumatic, high wear, sanitary inlet/outlet

Graco’s low shear back pressure regulator (BPR) minimizes shear and prevents paint degradation so that manufacturers produce consistent finish quality.

Air operated model works with Intelligent Paint Kitchen (IPK) control to reduce energy consumption and paint shear
Ultralife series ceramic coated parts resist wear and increase service life
Low profile, compact design and backwards compatibility mean easy installation and replacement

Compatible Material: Waterborne, Solvent borne

Gauge Port Size (cm): 0.635
Gauge Port Size (in): 1/4
Gauge Port Size (mm): 6.35
Gauge Port Type: NPT
Inlet Size (cm): 3.8
Inlet Size (in): 1.5
Inlet Size (mm): 38
Inlet Thread Type: Sanitary Flange
Maximum Air Inlet Pressure (bar): 7
Maximum Air Inlet Pressure (kg/cm²): 7
Maximum Air Inlet Pressure (kPa): 690
Maximum Air Inlet Pressure (psi): 100
Maximum Flow Rate (GPM): 25
Maximum Flow Rate (L/min): 95
Maximum Operating Temperature (°C): 50
Maximum Operating Temperature (°F): 122
Maximum Regulated Pressure (bar): 17.6
Maximum Regulated Pressure (kg/cm²): 17.6
Maximum Regulated Pressure (kPa): 1724
Maximum Regulated Pressure (psi): 250
Maximum Viscosity (cP): 1000
Maximum Working Pressure (bar): 21.1
Maximum Working Pressure (kg/cm²): 21.1
Maximum Working Pressure (kPa): 2068
Maximum Working Pressure (psi): 300
Minimum Operating Temperature (°C): 0
Minimum Operating Temperature (°F): 32
Minimum Regulated Pressure (bar): 1.8
Minimum Regulated Pressure (kg/cm²): 1.8
Minimum Regulated Pressure (kPa): 172
Minimum Regulated Pressure (MPa): 0.17
Minimum Regulated Pressure (psi): 25
Outlet Size (cm): 3.8
Outlet Size (in): 1.5
Outlet Size (mm): 38
Outlet Thread Type: Sanitary Flange

$3,430.00

Fusion PC Gun, Rnd, 00

GG 25P587

Fusion PC Gun, Rnd, 00, 00

Fusion ProConnect Gun with Round 00 Mix Chamber and 0.029 in (0.74 mm) Orifice Size A perfect rebuild in seconds is now possible with the revolutionary Fusion PC (ProConnect) gun, featuring an all-in-one cartridge head that replaces multiple individual parts of the fluid section with a single component. Simply replacing the cartridge completely eliminates the need for a time-consuming traditional rebuild, keeping you spraying and minimizing costly downtime. Unlike any other spray foam gun available A single cartridge replaces the entire fluid section in seconds Built on top of the time-tested Fusion Air Purge platform, the PC gun sprays exactly like a Fusion AP Integrated check valves for cross-over containment 13 parts are replaced by a single ProConnect cartridge Eliminates the need to purchase fluid section o-rings Spare ProConnect cartridges can replace your back-up guns Retrofit Kit available to convert existing Fusion AP guns

$3,870.00

Hose, Fluid, Wb, Aa, 36 ft

GG 25R013

Hose, Fluid, Wb, Aa, 36 ft

$4,120.00

Kit, Repair, Seal

GG 25R371

Kit, Repair, Seal

$166.00

Kit, Ball and Seat, Repair, S6

GG 25R213

Kit, Ball and Seat, Repair, S6

$640.00

Gear, Assembly, Acid

GG 25R349

GEAR,ASSEMBLY, ACID

$1,515.00

KIT, FUSION PC, RETRO, RND, 00

GG 25P700

KIT, FUSION PC, RETRO, RND, 00

Fusion ProConnect Retrofit Kit with Round 00 Mix Chamber and 0.029 in (0.74 mm) Orifice Size Transform your Fusion Air Purge gun into a Fusion PC with the ProConnect Retrofit Kit, allowing you to take full advantage of what the Fusion PC delivers: A perfect rebuild in seconds. The Retrofit Kit is compatible with all Fusion AP guns and is available in multiple mix chamber sizes. Acquire all the advantages of the revolutionary Fusion ProConnect while utilizing your existing Fusion AP handle and fluid manifold. Same Fusion AP gun, all new possibilities A single cartridge replaces the entire fluid section in seconds Sprays exactly like a Fusion AP Integrated check valves for cross-over containment 13 parts are replaced by a single ProConnect cartridge Eliminates the need to purchase fluid section o-rings Spare ProConnect cartridges can replace your back-up guns

$1,615.00

Kit, Low Level Sensor

GG 25R439

Kit, Low Level Sensor

$600.00

KIT, COVER, FRONT, NO LOGO, CLEAR

GG 24Z962

KIT, COVER, FRONT, NO LOGO, CLEAR

Graco 24Z962 Electric Grease Jockey® Pump Protective Pump Cover

Application: For increased control panel impact protection on Electric Grease Jockey, G3, and G1 Automatic Lubrication Pumps

Protective pump cover

Model: Grease Jockey

For Use With: Grease Jockey Pumps
Number of Pieces: 3

$65.00

T3 PUMP, CS

GG 24Z834

T3 PUMP, CS

T3 Supply Pump (Carbon Steel): 3:1 Fluid to Air Ratio Transfer Pumps are required to move A and B materials to the Reactor Spray Systems. The T3 Transfer Pump combines Graco’s proven Merkur air-motor and popular T2 stainless steel lower. The T3 is a 3:1 ratio pump – using less air pressure to provide the same fluid pressure required. Easier to maneuver - The overall height of the T3 is 3.7 inches (9.4 cm) shorter above the drum than the T2, making it easier to remove from the drum inside of a spray rig. More quiet – Studies show the T3 Transfer Pump is about 3x more quiet than the T2 Transfer Pump. Less maintenance - the Merkur air-motor is based on air pilot valve technology. The air-motor switchingis purely pneumatic. This differs from T1 and T2 Transfer Pumps, which use a mechanicalreversing mechanism in the air-motor

$1,695.00

Kit, Aircap Seals

GG 253032

Kit, Aircap Seals

$52.25

Kit, Repair, Brg, Helical Flwmtr

GG 253215

KIT, REPAIR, BRG, HELICAL FLWMTR

KIT INCLUDES: HOUSING, MIDDLE, HELICAL GEAR MTR [QTY. 1], INSERT, BEARING, HELICAL GEAR MTR [QTY. 2], INSERT, BEARING, HELICAL GEAR MTR [QTY. 1], BEARING, GEAR [QTY. 3], BALL, BEARING [QTY. 3], O-RING, SEAL, HELICAL GEAR METER [QTY. 2], LUBRICANT, GREASE [QTY. 1], PIN, DOWEL, .550 in. [QTY. 2], PIN, DOWEL, .750 in. [QTY. 2]

$2,290.00

Kit, Repair, Hose/Spring Tof55

GG 253289

KIT,REPAIR,HOSE/SPRING TOF55

KIT INCLUDES: HOSE, FOLLOWER, 1 in. [QTY. 2], CLAMP, TIRE [QTY. 1]

$1,695.00

Kit, Repair, Throat Seal, Hotmlt

GG 253545

KIT,REPAIR,THROAT SEAL,HOTMLT

KIT INCLUDES: NUT, PACKING [QTY. 1], PACKING, U-CUP [QTY. 2], WASHER, SEAL, BACK-UP [QTY. 1], PACKING, O-RING [QTY. 1], LUBRICANT, TUBE, 1 OZ [QTY. 1], WASHER, ROD, SCRAPER [QTY. 1], WASHER, SCRAPER, GREASE ZONE [QTY. 1], LUBRICANT, SYNTHETIC, GREASE, 3 OZ [QTY. 1]

$986.00

Seat, Valve

GG 253483

SEAT, VALVE

Graco 253483 Intake Valve Seat with Pressure Relief Valve, Carbide Seat

$646.00

Pump, Disp, Recip, Max WPR 1000PS

GG 253597

PUMP, DISP, RECIP MAX WPR 1000PS

Graco 253597 Dura-Flo 1000 cc Lower, Carbon Steel, UHMWPE/Leather Packings

$10,280.00

KIT, DIAPHRAGM, PTFE-EPDM, 1040

GG 253626

KIT, DIAPHRAGM, PTFE-EPDM, 1040

PTFE/EPDM Overmold Diaphragm Kit for 1-inch Pump

$1,045.00

Kit, Repl, Hd, Ptfe Diaph, 2150

GG 253628

Kit, Repl, Hd, Ptfe Diaph, 2150

$2,300.00

Frame, Accy, Stand, Pump

GG 253692

FRAME, ACCY, STAND, PUMP

Graco 253692 Floor Stand for NXT, E-Flo DC and Viscount Motors (750-2000 cc)

$1,405.00

Housing, Valve, Seat

GG 253741

HOUSING,VALVE,SEAT

$2,310.00

Housing, Valve, Seat

GG 253742

HOUSING,VALVE, SEAT

$839.00

Housing, Valve, Seat, Assy

GG 253743

HOUSING, VALVE, SEAT, ASSY

$613.00

Kit, Repair, Packing

GG 253744

KIT, REPAIR, PACKING

Graco 253744 UHMWPE and Leather Packings Repair Kit, for Dura-Flo 1800 (standard for 249992, L430SM, L430CM)

KIT INCLUDES: GLAND, PACKING, MALE [QTY. 1], GLAND, PACKING, FEMALE [QTY. 1], PACKING, VEE [QTY. 3], GLAND, PACKING, FEMALE [QTY. 1], PACKING, VEE [QTY. 3], PACKING, VEE, UHMWPE, SUBMICRON [QTY. 2], GLAND, PACKING, MALE [QTY. 1], PACKING, VEE, LEATHER [QTY. 4 ], PACKING, O-RING [QTY. 1], SEAL, ACETAL [QTY. 2], PACKING, O-RING [QTY. 1]

$1,230.00

Kit, Repair, Packings

GG 253745

KIT, REPAIR, PACKINGS

Graco 253745 UHMWPE and Leather Packings Repair Kit, for Dura-Flo 2400 (standard for 249991, L580SM)

KIT INCLUDES: PACKING, VEE [QTY. 3], GLAND, PACKING, MALE [QTY. 1], GLAND, PACKING, FEMALE [QTY. 1], PACKING, VEE [QTY. 3], GLAND, PACKING, MALE [QTY. 1], GLAND, PACKING, FEMALE [QTY. 1], PACKING, VEE, UHMWPE, [QTY. 2], PACKING, VEE, LEATHER [QTY. 4 ], PACKING, O-RING [QTY. 1], SEAL, ACETAL [QTY. 2], PACKING, O-RING [QTY. 1]

$652.00

KIT, SEAL, AIR MOTOR, A-20

GG 255057

KIT, SEAL, AIR MOTOR, A-20

Call for pricing

Kit, Repair, 1590 3A Diaphragm

GG 255058

Kit, Repair, 1590 3A Diaphragm

$1,520.00

KIT, DIAPHRAGM-F2 PT

GG 255060

KIT, DIAPHRAGM-F2 PT

PTFE Diaphragm Kit for 1.5-inch Pump

$994.00

KIT, REPAIR, AIR VALVE, SST

GG 255061

KIT, REPAIR, AIR VALVE, SST

Air Valve Repair Kit

$125.00

Kit, Filter, 80 Mesh, 2 Pack

GG 255082

Kit, Filter, 80 Mesh, 2 Pack

$53.75

Kit, Repair, Air Valve, 3150 3A

GG 255122

Kit, Repair, Air Valve, 3150 3A

$249.50

Kit, Bracket, Mounting

GG 255143

KIT, BRACKET, MOUNTING

Graco 255143 NXT Wall Mounting Kit

$740.00

Kit, Drain Valve, Set

GG 255148

Kit, Drain Valve, Set

$837.00

Kit, Drain Valve, Iso

GG 255149

Kit, Drain Valve, Iso

$436.00

Kit, Drain Valve, Resin

GG 255150

Kit, Drain Valve, Resin

$436.00

Kit, Repair, Seat/Needle

GG 255160

KIT, REPAIR,SEAT/NEEDLE

Graco 255160 Needle/ Seat Repair Kit for G40 Air Assisted Spray Gun

$315.00

MD2 Valve, Dispense, 1:1, Soft Seats

GG 255179

MD2 Valve, Dispense, 1:1, Soft Seats

MD2 Valve, 1:1 Ratio, Soft Seat, Adjustable Snuff-back Mixing dispense (MD) valve for 2 component materials minimizes maintenance while maximizing production. Static valve reliably dispenses and mixes a wide range of 2 component sealants and adhesives. 1:1 ratio nose handles a wide range of material. Soft seats with ultra-high molecular weight polyethylene (UHMWPE) seals are good for precise snuff-back control. Snuff-back control prevents dripping as it brings material back into the valve until next dispense. Adjustable snuff-back control finetunes shut-off performance for a clean bead dispense. Maximum flow rate is 25 cc/s, depending on material viscosity. Independent air cylinder improves mean time to repair (MTTR). No unique tools are required for maintenance or repair.

$5,230.00

MD2 Valve, Dispense, 1:1 Hard Seats

GG 255180

MD2 Valve, Dispense, 1:1 Hard Seats

MD2 Valve, 1:1 Ratio, Hard Seat, Non-adjustable Snuff-back Mixing dispense (MD) valve for 2 component materials minimizes maintenance while maximizing production. Static valve reliably dispenses and mixes a wide range of 2 component sealants and adhesives. 1:1 ratio nose handles a wide range of material. Carbide hard seats and hardened needles are good for abrasive material and stall against pressure applications. Snuff-back control prevents dripping as it brings material back into the valve until next dispense. Non-adjustable snuff-back control keeps shut-off performance consistent for a clean bead dispense. Maximum flow rate is 25 to 30 cc/s, depending on material viscosity. No unique tools are required for maintenance or repair. Grease isolation chamber protects moisture sensitive materials and has accessible grease fittings for easy maintenance

$5,230.00

MD2 VALVE, DISPENSE, 10:1, SOFT SEATS

GG 255181

MD2 VALVE, DISPENSE, 10:1, SOFT SEATS

MD2 Valve, 10:1 Ratio, Soft Seat, Adjustable Snuff-back Mixing dispense (MD) valve for 2 component materials minimizes maintenance while maximizing production. Static valve reliably dispenses and mixes a wide range of 2 component sealants and adhesives. 10:1 ratio nose handles a wide range of material. Soft seats with ultra-high molecular weight polyethylene (UHMWPE) seals are good for precise snuff-back control. Snuff-back control prevents dripping as it brings material back into the valve until next dispense. Adjustable snuff-back control finetunes shut-off performance for a clean bead dispense. Maximum flow rate is 25 cc/s, depending on material viscosity. Independent air cylinder improves mean time to repair (MTTR). No unique tools are required for maintenance or repair.

$6,040.00

MD2 VALVE, DISPENSE, 10:1 HARD SEATS

GG 255182

MD2 VALVE, DISPENSE, 10:1 HARD SEATS

MD2 Valve, 10:1 Ratio, Hard Seat, Non-adjustable Snuff-back Mixing dispense (MD) valve for 2 component materials minimizes maintenance while maximizing production. Static valve reliably dispenses and mixes a wide range of 2 component sealants and adhesives. 10:1 ratio nose handles a wide range of material. Carbide hard seats and hardened needles are good for abrasive material and stall against pressure applications. Snuff-back control prevents dripping as it brings material back into the valve until next dispense. Non-adjustable snuff-back control keeps shut-off performance consistent for a clean bead dispense. Maximum flow rate is 25 to 30 cc/s, depending on material viscosity. No unique tools are required for maintenance or repair. Grease isolation chamber protects moisture sensitive materials and has accessible grease fittings for easy maintenance

$6,040.00

Extension, Nozzle

GG 255194

Extension, Nozzle

$78.25

Module, Battery

GG 255197

Module, Battery

$24.70

KIT, REPAIR, PUMP

GG 255204

KIT, REPAIR, PUMP

Graco 255204 210ES Pump Repair Kit

All packing&prime, s should be replaced at one time to keep wear even. For use with Graco models 190ES, 210ES or other Graco 200 series sprayers. Kit includes all components to replace the packing set for the pump

Application: The Graco Endurance Pump Repair Kit extends the life of your sprayer. Preventive maintenance lowers ownership costs and reduces downtime. Replace the wear parts in the pump when there is noticeable loss of pressure or if fluid is leaking out of the front of the sprayer.

All packing&prime, s should be replaced at one time to keep wear even
For use with Graco models 190ES, 210ES or other Graco 200 series sprayers
Keep a spare kit on hand to minimize sprayer downtime

For Use With: Pro190ES Cart, Pro190ES Stand, Pro210ES Cart, Pro210ES Stand, Pro230ES Stand, Pro230ES Cart, Pro270ES Stand, Pro270ES Cart, Pro270GS

$96.50

HANDLE, VALVE, AIR

GG 255206

HANDLE, VALVE, AIR

$870.00

HANDLE, 2K DISP. VALVE, ELEC.

GG 255208

HANDLE, 2K DISP. VALVE, ELEC.

Graco 255208 MD2 Valve Electric Switch Handle

Convert any MD2 valve to a hand held valve with an internal normally open switch

$1,125.00

Kit, Replacement, Wrist Pin

GG 255216

Kit, Replacement, Wrist Pin

$349.00

Kit, Seal, Cylinder, Air, Valve

GG 255217

KIT, SEAL,CYLINDER,AIR,VALVE

KIT INCLUDES: PACKING, O-RING [QTY. 3], PACKING, O-RING [QTY. 2], PACKING, O-RING, BUNA-N [QTY. 2], BEARING, SLEEVE 1/4, 3/8, 1/4NYL [QTY. 2], LUBRICANT, GREASE [QTY. 1]

$87.00

Kit, Seal, Lube, Valve

GG 255218

KIT, SEAL,LUBE,VALVE

KIT INCLUDES: PACKING, O-RING [QTY. 2], O-RING, [QTY. 2], SEAL, POSIPAK [QTY. 2], PACKING, O-RING, BUNA-N [QTY. 2], SHAFT, PRIMARY [QTY. 2], PACKING, U-CUP URT 1/4, 1/2, 1/8 UR [QTY. 2]

$385.00