Parts

GG FFLP312

RAC X FFLP TIP, SPRAY, (312)

Graco FFLP312 Fine Finish Low Pressure RAC X FF LP SwitchTip, 312

Spray at up to 50% lower pressure with the Reverse-A-Clean (RAC) 312 Fine Finish Low Pressure (FF LP) RAC X SwitchTip. This fine finish tip produces a 6 to 8 inch Fan pattern and has a 0.012 inch orifice, ideal for finishing materials. Reverse the SwitchTip to easily clear clogs.

• Less Prep & Cleanup Time

  Less mess with less overspray

  Put the paint where you want it

• Easiest Pattern Overlap

  Softer spray fan pattern

  Easy to apply any material to any surfance

  Consistent blended finish quality

• Extended Life

  Spraying at half pressure doubles tip life

  Reduced sprayer maintenance - up to 2X life

• Best Tip on the Market

  Works with any airless sprayer

  Longest lasting Fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: FF LP SwitchTip

• Compatible Material: Primer, Stains, Varnish, Water-Based Paint, Enamel, Latex, Solvent borne Paints

• For Use With: RAC X HandTite Tip Guard

• Material: Tungsten Carbide

• Maximum Fan Width (cm): 15
• Maximum Fan Width (in): 6
• Maximum Fan Width (mm): 203

• Maximum Flow Rate (GPM): 0.15
• Maximum Flow Rate (L/min): 0.57

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 6
• Minimum Fan Width (mm): 152

• Orifice Diameter (in): 0.012

• Pattern Size (in): 6 to 8
• Pattern Size (mm): 152.4 to 203.2

GG FFLP514

RAC X FFLP TIP, SPRAY, (514)

Graco FFLP514 Fine Finish Low Pressure RAC X FF LP SwitchTip, 514

Spray at up to 50% lower pressure with the Reverse-A-Clean (RAC) 514 Fine Finish Low Pressure (FF LP) RAC X SwitchTip. This fine finish tip produces a 10 to 12 inch Fan pattern and has a 0.014 inch orifice, ideal for finishing materials. Reverse the SwitchTip to easily clear clogs.

• Less Prep & Cleanup Time

  Less mess with less overspray

  Put the paint where you want it

• Easiest Pattern Overlap

  Softer spray fan pattern

  Easy to apply any material to any surfance

  Consistent blended finish quality

• Extended Life

  Spraying at half pressure doubles tip life

  Reduced sprayer maintenance - up to 2X life

• Best Tip on the Market

  Works with any airless sprayer

  Longest lasting Fan pattern

  Highest quality finish with a consistent spray pattern

• Easy to Identify Tip Size

  Large raised tip size numbers are always legible - even when covered with paint

• Superior Tip Design

  Locking tab ensures tip stays securely in guard

  Snaps tip in spray or reverse position

  OneSeal tip gasket installs with no tools

  Solvent seal available when using extremely hot solvents

• Model: RAC X
• Series: FF LP SwitchTip

• Compatible Material: Primer, Stains, Varnish, Water-Based Paint, Enamel, Latex, Solvent borne Paints

• For Use With: RAC X HandTite Tip Guard

• Material: Tungsten Carbide

• Maximum Fan Width (cm): 25
• Maximum Fan Width (in): 10
• Maximum Fan Width (mm): 305

• Maximum Flow Rate (GPM): 0.21
• Maximum Flow Rate (L/min): 0.79

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 10
• Minimum Fan Width (mm): 254

• Orifice Diameter (in): 0.014

• Pattern Size (in): 10 to 12
• Pattern Size (mm): 254 to 304.8

GG FK2213

KIT, 1590 FG SS, PT, PO, EP

Graco FK2213 SaniForce 1590 FG Complete Fluid Repair Kit with SS Seat, PT Ball, PO Diaphragm, EP Seal

GG FT0638

GG GC0257

GG GC0624

GG GC1926

GG GC2520

GG GG4421

GG GG4619

GG HXD525

GG JC40M9

HIGH-FLO PUMP, 2200/1000, LOW DT, OPN, NPT

Graco JC40M9 High-Flo 4-Ball Pump, CS, 4:1, Low Noise Exhaust, DataTrak, Open Wet Cup Lower, NPT Fittings, Ultralife Rod/Cylinder

Pneumatic High-Flo 4-ball piston pumps provide high output per cycle to reduce pump wear and maintenance. Ideal for low pressure, high flow applications and inherently safe for hazardous locations.

• Slow-moving reciprocating motion does not damage paint like other rotary pumping technologies
• Rugged body armor, won't rust or dent
• De-icing controls eliminate stalling
• DataTrak tracks material usage, monitors and protects your pump

• Model: High-Flo
• Series: 4-Ball

• Application: Circulation

• Compatible Material: Waterborne, Solvent borne, High Solids, Xirallic, Metallics, Topcoats, Stains, Varnish, CARC

• Fluid Outlet Size (in): 1-1/2
• Fluid Outlet Size (mm): 38.1
• Fluid Outlet Thread Type: NPT
• Fluid Section Type: Open Wet Cup

• Includes: Carbon Steel Pump, Low Noise Exhaust, DataTrak Monitor, NPT Fittings, Ultralife Rods, Ultralife Cylinder

• Material: Carbon Steel

• Maximum Air Inlet Pressure (bar): 6.9
• Maximum Air Inlet Pressure (kPa): 690
• Maximum Air Inlet Pressure (psi): 100

• Maximum Continuous Cycle Rate (CPM): 12

• Maximum Flow Rate (GPM): 16.9
• Maximum Flow Rate (L/min): 63.97

• Maximum Operating Temperature ( degree C): 66
• Maximum Operating Temperature ( degree F): 150

• Maximum Working Pressure (bar): 31
• Maximum Working Pressure (kPa): 3100
• Maximum Working Pressure (MPa): 3.1
• Maximum Working Pressure (psi): 450

• Motor Type: Low Noise NXT with DataTrak

• Portable: Non-Portable

• Pump Ratio: 4:1

GG L100CM

LOWER, CM100 MAXLIFE

Graco L100CM Carbon Steel MaxLife Check-Mate 100 Lower

• Model: Check-Mate

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Bonding, Sealing, Gasketing, Potting, Encapsulation, Molding, Spray, Fluid Transfer, Unloading, Underfill

• Fluid Outlet Size (in): 3/4
• Fluid Outlet Thread Gender: Male
• Fluid Outlet Thread Type: NPT

• For Use With: Check-Mate Pump Packages

• Maximum Flow Rate (GPM): 1.6

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 100

• Maximum Pump Speed (CPM): 60

• Maximum Working Pressure (psi): 6300

GG L100S1

LOWER, CHEMICAL, 100, SST, UCUP

Graco L100S1 Z-Pump, 100 cc, Severe Duty, S1

Z-Pumps are positive displacement pump components for use with the Graco meter, mix, and dispense systems and are ideal for two-component sealant and adhesives requiring precision ratio, flow, and volume controls.

• Severe Duty coatings and 1 inch (2.54 cm) checks easily manage material wear from silicones, sealants, epoxies, foam, and structural adhesives.
• Precision control eliminates pressure spikes and guarantees on ratio dispense.
• Pump seals are the only wear parts, which reduces maintenance downtime and repair costs.

• Model: Z-Pump
• Series: S1

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Industrial

• Ball Check Size (in): 1
• Ball Material: Silicon Nitride

• Coating Type: Severe Duty

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 1.905
• Fluid Inlet Size (in): 3/4
• Fluid Inlet Thread Gender: Female
• Fluid Inlet Thread Type: NPT

• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: SAE

• For Use With: HFR

• Maximum Flow Rate (GPM): 1.59

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 100

• Maximum Pump Speed (CPM): 60

• Maximum Viscosity (cP): 3000000

GG L150S1

GG L180C1

GG L200SS

LOWER, CM200 SEVERE DUTY SST

Graco L200SS Stainless Steel Severe Duty Check-Mate 200 Lower

• Model: Check-Mate

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Bonding, Sealing, Gasketing, Potting, Encapsulation, Molding, Spray, Fluid Transfer, Unloading, Underfill

• Fluid Outlet Size (in): 1
• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: NPT

• For Use With: Check-Mate Pump Packages

• Maximum Flow Rate (GPM): 3.2

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 200

• Maximum Pump Speed (CPM): 60

• Maximum Working Pressure (psi): 6200

GG L250CS

LOWER, CM250 SEVERE DUTY

Graco L250CS Carbon Steel Severe Duty Check-Mate 250 Lower

• Model: Check-Mate

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Bonding, Sealing, Gasketing, Potting, Encapsulation, Molding, Spray, Fluid Transfer, Unloading, Underfill

• Fluid Outlet Size (in): 1
• Fluid Outlet Thread Gender: Female
• Fluid Outlet Thread Type: NPT

• For Use With: Check-Mate Pump Packages

• Maximum Flow Rate (GPM): 4

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 250

• Maximum Pump Speed (CPM): 60

• Maximum Working Pressure (psi): 6200

GG L290C2

GG L500CS

LOWER, CM500 SEVERE DUTY

Graco L500CS Carbon Steel Severe Duty Check-Mate 500 Lower

• Model: Check-Mate

• Ambient/Warm Melt/Hot Melt: Ambient
• Application: Bonding, Sealing, Gasketing, Potting, Encapsulation, Molding, Spray, Fluid Transfer, Unloading, Underfill

• Fluid Outlet Size (in): 1-1/2
• Fluid Outlet Thread Gender: Male
• Fluid Outlet Thread Type: NPT

• For Use With: Check-Mate Pump Packages

• Maximum Flow Rate (GPM): 8

• Maximum Operating Temperature ( degree F): 180
• Maximum Output (cm cu ): 500

• Maximum Pump Speed (CPM): 60

• Maximum Working Pressure (psi): 3900

GG LC0005

GG LC0019

GG LC0098

GG LC0310

GG LC0318