Parts

GG 257641

KIT, SEAL, 20L, SINGLE, PTFE

KIT INCLUDES: SPACER, [QTY. 1], WIPER, MAIN [QTY. 1], WIPER, PE SUPPORT [QTY. 1], PLATE, BOTTOM, PLATEN [QTY. 1], O-RING, PACKING -162 [QTY. 1], CLAMP, 20 LITER, RETAINING [QTY. 1], NUT, 1/4 HEX W/ TOOTH WASHER [QTY. 12 ], WIPER, SUPPPORT [QTY. 1], COVER, 20L, SHROUD [QTY. 1], PIN, HAIRPIN, COTTER [QTY. 2], LUBRICANT, GREASE [QTY. 1]

GG 258669

Sensor, Assembly

GG 258770

Kit, Piston Seals

GG 25A246

Kit, Seal, Pump Displ. 65:1

GG 25C213

Kit, O-rings, 50 MM Air Cap

GG 25C818

KIT, SEAT 1050M SS

1-inch 316 Stainless Steel Seat Kit

GG 25M213

Indicator

GG 25P850

Kit, O-Ring, Air, Fusion Pc

GG 25T845

KIT,SLEEVE,GUIDE,6.5 RAM

GG 269619

CONTRACTOR FLAT TIP, SPRAY

Contractor Flat Tip, 619 The 619 Contractor Flat Tip produces a 12 to 14 inch fan and has a 0.019 inch orifice.

GG 286315

RAC 5 TIP, SPRAY

RAC 5 SwitchTip, 315 The Reverse-A-Clean (RAC) 315 RAC 5 SwitchTip is designed for narrow surfaces. The 315 SwitchTip has a 0.015 inch orifice and produces a 6 to 8 inch fan. Reverse the SwitchTip to easily clear clogs. Used for residential, commerical or industrial applicaitions. Best used with materials ranging from lacquers, latex paints and mastics. Most Widely Used Reversible Spray Tip on the Market (Black Handle)

• Used for residential and commercial applications
• Includes OneSeal for most common coatings
• Large selection of tip sizes available
• Easy to identify laser stamped tip size
• Solvent seal available when using extremely hot solvents

GG 286655

RAC 5 TIP, SPRAY

RAC 5 SwitchTip, 655 The Reverse-A-Clean (RAC) 655 RAC 5 SwitchTip produces a 12 to 14 inch fan and has a 0.055 inch orifice. Reverse the SwitchTip to easily clear clogs.

Most Widely Used Reversible Spray Tip on the Market (Black Handle)

Used for residential and commercial applications

Includes OneSeal for most common coatings

Large selection of tip sizes available

Easy to identify laser stamped tip size

Solvent seal available when using extremely hot solvents

GG 288221

MANIFOLD, BOTTOM INLET (IN)

Graco 288221 Manifold with bottom fluid ports

GG 289046

Kit, Air Cap, Waterborne, Conv

GG 289053

Kit, Air Cap, Spatter, Hvlp

GG 289496

Kit, Needle And Nozzle, .070

GG 289800

Kit, Needle

GG 514237

Screw

GG 5-441-02

1/2 Mixer Shaft Seal

GG 551794

Cylinder, Pneumatic

GG 564086

Tube, 3/16 10 Ft. Black Precharged

GG 626065

Housing, Lube

GG 687056

Packing Vee

GG 687057

Packing Vee

GG 830353

REGULATOR, LOW PRESSURE

Graco 830353 Low Pressure Fluid Regulator, 250 Max psi, 3-100 psi Range, 3.0 GPM, SST, Air Type, 3/8 (f) x 1/4 (f)

Fluid pressure regulators control pressure of the downstream fluid, allowing operators to accurately control the pressure to guns, applicators and dispense valves

• Actuation Type: Air
• Includes: Regulator Only
• Inlet Size (cm): 0.9525
• Inlet Size (in): 3/8
• Inlet Size (mm): 9.525
• Inlet Thread Type: NPSM
• Maximum Flow Rate (GPM): 3
• Maximum Flow Rate (L/min): 11.36
• Maximum Regulated Pressure (bar): 7.0
• Maximum Regulated Pressure (kPa): 700
• Maximum Regulated Pressure (MPa): 0.7
• Maximum Regulated Pressure (psi): 100
• Maximum Viscosity (cP): 1000
• Maximum Working Pressure (bar): 18
• Maximum Working Pressure (kPa): 1800
• Maximum Working Pressure (MPa): 1.8
• Maximum Working Pressure (psi): 250
• Minimum Regulated Pressure (bar): 0.2
• Minimum Regulated Pressure (kPa): 20
• Minimum Regulated Pressure (MPa): 0.02
• Minimum Regulated Pressure (psi): 3
• Outlet Size (cm): 0.635
• Outlet Size (in): 1/4
• Outlet Size (mm): 6.35