Parts
MHH VALVE, CHECK, 1/8 NPT, REV, 5000
GG 563200
MHH VALVE, CHECK, 1/8 NPT, REV, 5000
Graco 563200 Single Ball Check Valve - 35 psi Nominal Cracking Pressure, 1/8 in NPSF (F) x 1/8 in NPTF (M), Steel, 5,000 psi
- Lubriquip part number 509-355-030
- Trabon part number 9355-35
- Application: Compressor Equipment
- Ball Material: Steel
- Body Material: Steel
- Compatible Material: Oil, Grease
- Inlet Size (cm): 0.3175
- Inlet Size (in): 1/8
- Inlet Size (mm): 3.175
- Inlet Thread Gender: Female
- Inlet Thread Type: NPT
- Maximum Working Pressure (bar): 345
- Maximum Working Pressure (kPa): 34500
- Maximum Working Pressure (MPa): 34.5
- Maximum Working Pressure (psi): 5000
- Number of Balls: Single Ball
- Outlet Size (cm): 0.3175
- Outlet Size (in): 1/8
- Outlet Size (mm): 3.175
- Outlet Thread Gender: Female
- Outlet Thread Type: NPS
AA Tip, 011, 10 in pattern
GG AEM511
TIP,MANUAL,ES
Graco AEM511 AEM Fine Finish Spray Tips, 0.011 inch (0.279 mm) Orifice Size, 10-12 inches (250-300 mm) Fan Width
AA Tip .017, 10 in pattern
GG AEM517
TIP,MANUAL,ES
Graco AEM517 AEM Fine Finish Spray Tips, 0.017 inch (0.432 mm) Orifice Size, 10-12 inches (250-300 mm) Fan Width
- Coating Type: Abrasive, Metallic, High Conductivity, High Wear
- Compatible Paint Type: Automotive, Base Coat, Clear Coat, Enamels, High Solids, Metallics, Plural Component Materials, Primers, Solventborne, Urethanes
Automatic Metering Valve
GG C02078
VALVE, AUTOMATIC, METER
Graco C02078 Automatic Metering Valves- With double acting air cylinder, 7/16 - 20 unf mounting hole, 1/4 npt(f) material inlet and 1/4 npt(f) material outlet
Used to provide precise dispense of medium - to high - viscosity sealants and adhesives in a non - hazardous location.
- Air Inlet Size (cm): 0.3175
- Air Inlet Size (in): 1/8
- Air Inlet Size (mm): 3.175
- Air Inlet Thread Gender: Female
- Air Inlet Thread Type: NPT
RAC X FFLP TIP, SPRAY, (512)
GG FFLP512
RAC X FFLP TIP, SPRAY, (512)
Graco FFLP512 Fine Finish Low Pressure RAC X FF LP SwitchTip, 512
Spray at up to 50% lower pressure with the Reverse-A-Clean (RAC) 512 Fine Finish Low Pressure (FF LP) RAC X SwitchTip. This fine finish tip produces a 10 to 12 inch Fan pattern and has a 0.012 inch orifice, ideal for finishing materials. Reverse the SwitchTip to easily clear clogs.
Application: For fine finish applications- Less Prep & Cleanup Time
Less mess with less overspray
Put the paint where you want it
- Easiest Pattern Overlap
Softer spray fan pattern
Easy to apply any material to any surfance
Consistent blended finish quality
- Extended Life
Spraying at half pressure doubles tip life
Reduced sprayer maintenance – up to 2X life
- Best Tip on the Market
Works with any airless sprayer
Longest lasting Fan pattern
Highest quality finish with a consistent spray pattern
- Easy to Identify Tip Size
Large raised tip size numbers are always legible – even when covered with paint
- Superior Tip Design
Locking tab ensures tip stays securely in guard
Snaps tip in spray or reverse position
OneSeal tip gasket installs with no tools
Solvent seal available when using extremely hot solvents
- Model: RAC X
- Series: FF LP SwitchTip
- Compatible Material: Primer, Stains, Varnish, Water-Based Paint, Enamel, Latex, Solvent borne Paints
- For Use With: RAC X HandTite Tip Guard
- Material: Tungsten Carbide
- Maximum Fan Width (cm): 25
- Maximum Fan Width (in): 10
- Maximum Fan Width (mm): 305
- Maximum Flow Rate (GPM): 0.15
- Maximum Flow Rate (L/min): 0.57
- Maximum Working Pressure (bar): 280
- Maximum Working Pressure (kPa): 28000
- Maximum Working Pressure (psi): 4050
- Minimum Fan Width (in): 10
- Minimum Fan Width (mm): 254
- Orifice Diameter (in): 0.012
- Pattern Size (in): 10 to 12
- Pattern Size (mm): 254 to 304.8
RAC X LTX TIP, SPRAY, (651)
GG LTX651
RAC X LTX TIP, SPRAY, (651)
Graco LTX651 RAC X SwitchTip, 651
The Reverse-A-Clean (RAC) 651 RAC X SwitchTip produces a 12 to 14 inch fan and has a 0.051 inch orifice. Reverse the SwitchTip to easily clear clogs.
Application: Used for residential, commercial or industrial applications.- Best Tip on the Market
Longest lasting fan pattern
Highest quality finish with a consistent spray pattern
- Easy to Identify Tip Size
Large raised tip size numbers are always legible – even when covered with paint
- Superior Tip Design
Locking tab ensures tip stays securely in guard
Snaps tip in spray or reverse position
OneSeal tip gasket installs with no tools
Solvent seal available when using extremely hot solvents
- Model: RAC X
- Series: LTX SwitchTip
- Compatible Material: Lacquer to Mastic, Latex Paint
- For Use With: RAC X HandTite Tip Guard
- Maximum Fan Width (cm): 30
- Maximum Fan Width (in): 12
- Maximum Fan Width (mm): 356
- Maximum Flow Rate (GPM): 2.79
- Maximum Flow Rate (L/min): 10.56
- Maximum Working Pressure (bar): 280
- Maximum Working Pressure (kPa): 28000
- Maximum Working Pressure (psi): 4050
- Minimum Fan Width (in): 12
- Minimum Fan Width (mm): 305
- Orifice Diameter (in): 0.051
- Pattern Size (in): 12 to 14
- Pattern Size (mm): 304.8 to 355.6
Hopper Assembly, Hf05-50, w/Vent, 2H, Complete
GV 1017900
Hopper Assembly, Hf05-50, w/Vent, 2H, Complete
Payment options
