Hydraullic Units

EP LGHMS314EB

• Type: Puller
• Max PSI: 10150

• Product Group: Pullers
• Product Line: Industrial Tools
• Series: LGHMS
• SubTypes: Lock-Grip Master Puller Sets

• Capacity Imperial Tons: 14
• Capacity KN: 125

• All LGHMS-Series Master Puller Sets include an LGH-Series Puller, a Cross Puller, a Bearing Separator, a Bearing Cup Puller, a detachable Hollow Cylinder, a hose, a gauge and a pump
• LGH-Series Pullers provide the same safety and ease of use as their mechanical counterparts, with the pulling force applied by a standard 10,150 psi hydraulic cylinder.
• Quickly and easily mount on a wide range of applications
• Hydraulically applied pulling force increases pulling capacity, reducing operator fatigue
• Lock-on jaws offer a secure grip for safe and easy operation
• Synchronous jaw movement enables entire pulling job to be performed by a single operator
• LGH-Series Pullers MUST be used with a point protector if the shaft end does not contain a drilled center hole. One point protector is included with every puller.
• Enerpac cylinders and pumps can be operated to 10,150 psi, but should not be operated past 5,000 psi when using the Cross Bearing Puller Set tools.
• Always wear safety goggles and gloves while using pullers.

• Set Includes: LGH314, RWH121, FZ1065, LGH14K6, BHP172, BHP282, BHP190, PUD1300B, G2535L, HC7206C

EP LPL-1002

EP LW-16

EP NC2432

NC-Series Hydraulic Nut Splitters use a single blade configuration suited to general nut cutting applications across a wide range of industries.

The heat-treated steel blade with its optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NC-Series Nut Cutters are compact, simple, and easy to use. The ergonomic design ensures comfortable use, thanks to the carefully considered angled head design and handle position.

Nuts are often difficult to remove, and while loosening them using tightening tools is possible, this generally requires larger equipment and takes more time.

Using a cutting torch or a hammer and chisel presents safety risks and can cause damage to the joint components. They also involve significantly longer setup and operational time.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NC
• SubTypes: Nut Cutter

• bundleSet_IDs: NCB2432
• Capacity Imperial Tons: 15
• Capacity KN: 147

• Compact and ergonomic design, easy to use
• Unique angled head design
• Single-acting, spring return cylinder
• Heavy duty chisels can be reground
• Nut Splitters include spare chisel, spare set screw and wrench used to secure the chisel. A CR-400 coupler is standard.
• For applications with bolt sizes that are common to two tool model sizes, we recommend to select the larger of the two tools for the best results.
• These are not suited for square, star, round or stainless steel nuts. Maximum allowable hardness of nuts to be split is HRc-44.
• For materials and sizes not specified, contact Enerpac Technical Services.

• Accessories: NCB2432

EP NC3241

NC-Series Hydraulic Nut Splitters use a single blade configuration suited to general nut cutting applications across a wide range of industries.

The heat-treated steel blade with its optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NC-Series Nut Cutters are compact, simple, and easy to use. The ergonomic design ensures comfortable use, thanks to the carefully considered angled head design and handle position.

Nuts are often difficult to remove, and while loosening them using tightening tools is possible, this generally requires larger equipment and takes more time.

Using a cutting torch or a hammer and chisel presents safety risks and can cause damage to the joint components. They also involve significantly longer setup and operational time.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NC
• SubTypes: Nut Cutter

• Capacity Imperial Tons: 20
• Capacity KN: 196

• Compact and ergonomic design, easy to use
• Unique angled head design
• Single-acting, spring return cylinder
• Heavy duty chisels can be reground
• Nut Splitters include spare chisel, spare set screw and wrench used to secure the chisel. A CR-400 coupler is standard.
• For applications with bolt sizes that are common to two tool model sizes, we recommend to select the larger of the two tools for the best results.
• These are not suited for square, star, round or stainless steel nuts. Maximum allowable hardness of nuts to be split is HRc-44.
• For materials and sizes not specified, contact Enerpac Technical Services.

• Accessories: NCB3241

EP NC4150

NC-Series Hydraulic Nut Splitters use a single blade configuration suited to general nut cutting applications across a wide range of industries.

The heat-treated steel blade with its optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NC-Series Nut Cutters are compact, simple, and easy to use. The ergonomic design ensures comfortable use, thanks to the carefully considered angled head design and handle position.

Nuts are often difficult to remove, and while loosening them using tightening tools is possible, this generally requires larger equipment and takes more time.

Using a cutting torch or a hammer and chisel presents safety risks and can cause damage to the joint components. They also involve significantly longer setup and operational time.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NC
• SubTypes: Nut Cutter

• bundleSet_IDs: NCB4150
• Capacity Imperial Tons: 35
• Capacity KN: 343

• Compact and ergonomic design, easy to use
• Unique angled head design
• Single-acting, spring return cylinder
• Heavy duty chisels can be reground
• Nut Splitters include spare chisel, spare set screw and wrench used to secure the chisel. A CR-400 coupler is standard.
• For applications with bolt sizes that are common to two tool model sizes, we recommend to select the larger of the two tools for the best results.
• These are not suited for square, star, round or stainless steel nuts. Maximum allowable hardness of nuts to be split is HRc-44.
• For materials and sizes not specified, contact Enerpac Technical Services.

• Accessories: NCB4150

EP NC6075

NC-Series Hydraulic Nut Splitters use a single blade configuration suited to general nut cutting applications across a wide range of industries.

The heat-treated steel blade with its optimized cutting head geometry cuts from one side, and the powerful internal spring brings it back to its starting position.

NC-Series Nut Cutters are compact, simple, and easy to use. The ergonomic design ensures comfortable use, thanks to the carefully considered angled head design and handle position.

Nuts are often difficult to remove, and while loosening them using tightening tools is possible, this generally requires larger equipment and takes more time.

Using a cutting torch or a hammer and chisel presents safety risks and can cause damage to the joint components. They also involve significantly longer setup and operational time.

Nut splitting with the Enerpac Hydraulic Nut Splitters is the safest and most efficient method - taking less time and avoiding costly damage to joint components.

• Type: Cutter
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cutters
• Product Line: Industrial Tools, Bolting Tools
• Series: NC
• SubTypes: Nut Cutter

• Capacity Imperial Tons: 90
• Capacity KN: 882

• Compact and ergonomic design, easy to use
• Unique angled head design
• Single-acting, spring return cylinder
• Heavy duty chisels can be reground
• Nut Splitters include spare chisel, spare set screw and wrench used to secure the chisel. A CR-400 coupler is standard.
• For applications with bolt sizes that are common to two tool model sizes, we recommend to select the larger of the two tools for the best results.
• These are not suited for square, star, round or stainless steel nuts. Maximum allowable hardness of nuts to be split is HRc-44.
• For materials and sizes not specified, contact Enerpac Technical Services.

• Accessories: NCB6075

EP P142ALSS

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P
• SubTypes: Hand Pump - Two Speed

• Corrosion resistant, nickel-plated valves and cylinders
• Stainless steel pump inserts will not corrode
• Viton Seals provide heat and chemical resistance
• Anodized aluminum pump reservoirs and plastic encapsulated pump bodies resist wet environments
• Two-speed operation reduces pump handle strokes 78% compared to single-speed pumps
• Pump handles lock for easy carrying

• Spare Part(s): DA8802900SR, P142ALSSK

EP P143

EP P-18

EP P181190W

• Type: Service Kit

• Product Group: Pumps
• Product Line: Industrial Tools
• SubTypes: Relief Valve

EP P-2282

EP P25

These Low-Pressure Hydraulic Hand Pumps are durable, portable, highly efficient, and easy to use. Each model in the series features an all-steel construction, a chrome plated plunger, and a wiper system for long-lasting performance.

These pumps are constructed to power a wide range of single acting cylinders and tools in space restricted areas. The range includes the P51 that can be operated in the horizontal orientation only, and others also capable of operating in the vertical orientations: P18 with the pump head facing down, P25, P50 with the pump head facing up. Each is protected by external load-release valves and internal overload pressure-relief valves.

With a choice of oil capacities up to 200 in3 (3,277 cm3), and operating pressures of 2,500 psi (175 bar) - 5,000 psi (350 bar) you will find an Enerpac Low Pressure Hydraulic Hand Pump to suit your needs.

• Type: Hydraulic Pump
• Max Bar: 175
• Max PSI: 2500

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P
• SubTypes: Hand Pump - Single Speed

• P25 and P50 pumps oil in both forward and reverse handle movement improving overall efficiency, ideal when mounting space is restricted
• External load-release valve
• Internal pressure-relief valve for overload protection
• P25 and P50 vertical operation requires pump vent side facing up

• Spare Part(s): CA365024SR, P181190W, P50K1

EP P301D

• Heavy duty, metal construction for durability.
• High displacements of oil per stroke.
• Low, back saving handle effort.
• Large reservoir capacities.

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: P Steel
• SubTypes: Hand Pump - Heavy Duty Steel

EP P-392FP

EP P-462

EP P464

Ultima Steel Hand Pumps are durable, portable, and highly efficient. Each model in the series features an all-steel construction, a chrome plated plunger, and a wiper system for long-lasting performance.

All except the P39 are 2 stage pumps, which reduces the number of handle strokes by as much as 78% compared to a single speed pump. This is ideal for applications when high flow is needed at the first stage, (such as when advancing a cylinder to the point of load contact). The pump switches automatically to the second stage which is the low flow high-pressure stage.

With a choice of oil capacities up to 453 in3 (7423 cm3), you will find Ultima Steel Hand Pumps that can handle multiple cylinder hook-ups, including models to suit either single-acting and double-acting cylinders.

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P
• SubTypes: Hand Pump - Two Speed

• Reduced handle effort and ergonomic grip for less operator fatigue
• Vent free reservoir eliminates spills
• Quick grip handle allows for easy transport
• Integral reservoir over-pressurization protection

• Spare Part(s): P462K2, P462K3

EP P51

These Low-Pressure Hydraulic Hand Pumps are durable, portable, highly efficient, and easy to use. Each model in the series features an all-steel construction, a chrome plated plunger, and a wiper system for long-lasting performance.

These pumps are constructed to power a wide range of single acting cylinders and tools in space restricted areas. The range includes the P51 that can be operated in the horizontal orientation only, and others also capable of operating in the vertical orientations: P18 with the pump head facing down, P25, P50 with the pump head facing up. Each is protected by external load-release valves and internal overload pressure-relief valves.

With a choice of oil capacities up to 200 in3 (3,277 cm3), and operating pressures of 2,500 psi (175 bar) - 5,000 psi (350 bar) you will find an Enerpac Low Pressure Hydraulic Hand Pump to suit your needs.

• Type: Hydraulic Pump
• Max Bar: 200
• Max PSI: 3000

• Product Group: Pumps
• Product Line: Industrial Tools, Work Holding Tools
• Series: P
• SubTypes: Hand Pump - Single Speed

• External load-release valve
• Internal pressure-relief valve for overload protection
• P51 for horizontal operation only

• Spare Part(s): CJ589950W, P181190W, P51K1

EP P842

Enerpac lightweight hydraulic hand pumps are a convenient alternative to heavier steel pumps without any sacrifice in performance or safety. Each model is rated up to 10,000 psi (700 bar).

The durable glass-filled nylon reservoir and nylon encapsulated aluminum pump base offers an unrivalled combination of strength, weight, and resistance to corrosion.

Lightweight single-speed hydraulic hand pumps offer the simplicity needed for a wide range of industrial applications. The 2-stage hydraulic models reduce the number of handle strokes by as much as 78% compared to a single speed pump. This is ideal when you want to advance a tool such as a cylinder to the point of load contact. High flow is delivered when it's needed most before the pump automatically switches to the low flow high-pressure stage.

With a choice of oil capacities up to 453 in3 (7423 cm3), we're certain you'll find a lightweight hydraulic hand pump to handle multiple cylinder hook-ups. For compatibility with double-acting tools choose the P842.

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: P
• SubTypes: Hand Pump - Two Speed

• Lightweight and compact design
• Durable glass-filled nylon reservoir and nylon encapsulated aluminum pump base for maximum corrosion resistance
• Two-speed operation on most models reduces handle strokes by as much as 78% over single speed pumps
• Lower handle effort to minimize operator fatigue
• Handle lock and lightweight construction for easy carrying
• Large oil capacities to power a wide range of cylinders or tools
• Non-conductive fiberglass handle for operator safety
• Internal pressure relief valve for overload protection

• Spare Part(s): P842K50

EP PACG30S8SWM10

Enerpac PACG Air Hydraulic Pumps are for designed for intermittent to medium duty workholding applications up to 5,000 psi. Valve mount options include, remote, and mountings for DO3 and VP valves.

Enerpac Turbo II Air Over Hydraulic Pumps generate the hydraulic pressure you need using the air pressure you have available. The Air Saver Piston reduces air consumption, and the pump can start at low pressures from 50-125 psi.

Turbo II Air-Hydraulic Pumps are best suited to medium or lower cycle applications. They provide the power and speed needed for simple clamping circuits and mostly single acting tools. At only 75 dBA, the Turbo II Series helps to keep the noise level to a minimum.

Choose from a range with maximum working pressure of either 5,000 or 10,000psi, and various reservoir capacities from 116 - 462 in3 (2100 - 7500 cm3).

Turbo II Air Over Hydraulic Pump Series :

• PATG - Treadle for foot or hand operation
• PARG - Pendant Operation
• PAMG - Manual lever operated. For double-acting applications
• PACG - For remote valve mount. For workholding, 5000 psi (350 bar).
• PASG - Includes mount for a single DO3 Valve. For workholding, 5000 psi (350 bar).

• Type: Hydraulic Pump
• Max Bar: 350
• Max PSI: 5000

• Product Group: Pumps
• Product Line: Work Holding Tools
• Series: PACG
• SubTypes: Air Pump

• On-demand stall-restart operation maintains system pressure, providing clamping security
• External adjustable pressure relief valve (behind sight glass)
• Internal pressure relief valve provides overload protection
• Reduced noise level to 75 dBA
• Operating air pressure: 50-125 psi - enables pump to start at low air pressure**
• Hydraulic to air ratio: 45:1
• Reinforced heavy-duty lightweight reservoir for applications in tough environments
• Five valve mounting options provide flexibility in setup and operation
• Fully serviceable air motor assembly
• User supplied valves

** NOTE: From 50-125 psi air inlet pressure. Performance is significantly diminished below 50 psi. Performance may vary compared to listed values due to seal friction, internal pressure drops and manufacturing tolerances. Be sure to allow some flexibility on air inlet pressure.

EP PAMG1402N

PAMG Series air over hydraulic pumps include a manual lever operated 3-way valve. As part of the Turbo II Air Hydraulic Series, they provide the power and speed needed for simple clamping circuits.

PAMG3402NB, PAMG34S8N, PAMG5402NB, PAMG54S8N are for single-acting applications with a maximum operation pressure of 5000 psi (350 bar).

The PAMG1405N and the PAMG1402N pumps are compatible with double acting tools and provide Advance / Hold / Retract functions. Maximum operating pressure of 10,000 psi (700 bar).

Enerpac Turbo II Air Over Hydraulic Pumps generate the hydraulic pressure you need using the air pressure available. The Air Saver Piston reduces air consumption, and the pump can start at low pressures from 50-125 psi.

Turbo II Air-Hydraulic Pumps are best suited to medium or lower cycle applications. They provide all the power and speed needed for simple clamping circuits and single acting tools. At only 75 dBA, the Turbo II Series helps to keep the noise level to a minimum.

Choose from a range with maximum working pressure of either 5,000 or 10,000psi, and various reservoir capacities from 116 - 462 in3 (2100 - 7500 cm3).

Turbo II Air Over Hydraulic Pump Series :

• PATG - Treadle for foot or hand operation
• PARG - Pendant Operation
• PAMG - Manual lever operated. For double-acting applications
• PACG - For remote valve mount. For work holding, 5000 psi (350 bar).
• PASG - Includes mount for a single DO3 Valve.

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: PAMG
• SubTypes: Air Pump

• High efficiency cast aluminum air motor for increased life and reduced air consumption
• Reinforced heavy-duty reservoir for applications in tough environments
• New generation air saver piston with rugged one-piece design reduces air consumption and operating costs
• Return-to-tank port for use in remote valve applications
• Quiet - only 76dBA with low air consumption of 12 scfm
• Operating air pressure: 40-125 psi, enables pump to start at extremely low pressure
• Internal pressure relief valve provides overload protection

EP PMB2

• Type: Press Accessory

• Product Group: Presses
• Product Line: Industrial Tools
• Series: A
• SubTypes: Press Pump Mounting Bracket

• Heavy duty steel brackets to allow conversion to one of the Enerpac Power Sources to power your press.
• Both mounting brackets are pre-drilled to accept a number of different pump models

EP PRAMA10016L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 16
• Stroke MM: 406
• SubTypes: POW'R-RISER Jack Pneumatic

• Capacity Imperial Tons: 100
• Capacity KN: 889

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS60, PRU13, PRU14, PRU110, PRUS126, PRE5, PRE7, PRE9, PRE11, PRE14, PRE18, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PRASA10016L

• Type: Wheeled Jack
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: PR
• Stroke Inches: 16
• Stroke MM: 406
• SubTypes: POW'R-RISER Jack Pneumatic

• Capacity Imperial Tons: 100
• Capacity KN: 889

• 4-inch ground clearance for transport over rail and rough terrain
• Three-position handle provides easy tilt back and transport
• Complies with ASME/ANSI B30.1:2015 & CE specifications
• Easy-to-change external filter minimizes down time
• Rugged, fully enclosed 24-inch wide frame with no exposed fittings or hoses
• SUP-R-STACK™ Extension System allows lifting at all heights without blocking

• Accessories: PRTS60, PRU13, PRU14, PRU110, PRUS126, PRE5, PRE7, PRE9, PRE11, PRE14, PRE18, PRES6024, PRS1, PRS2, PRS3, PRS4

EP PUD1300B

PU Series electric over hydraulic pumps combine economy with high-performance - ideal for intermittent use when working with small to medium size cylinders and other hydraulic tools.

All models in the series are 2-speed for enhanced productivity, and each is supplied with a 10 ft (3 m) cord and control pendant for operator safety. The high-strength molded shroud with integral handle protects the motor from contamination and damage in industrial environments.

Within the PU Series is a selection of pumps that offer a choice of reservoir capacities, valve functions and voltage.

PUD1100 Series

• For advance and retract of single-acting cylinders
• For applications not requiring load holding
• Ideal for punching applications

PUD1300 Series

• Providing advance, hold, and retract of single-acting cylinders
• Ideal for applications requiring load holding
• For applications requiring solenoid valves

PUJ-Series

• Manual valves provide advance, hold, and retract operation
• 3 and 4-way valves for single or double-acting cylinders

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: PU
• SubTypes: Electric Pump - Economy

• The economic choice for small to medium sized tools.
• Lightweight, compact, and portable.
• Two-speed operation reduces cycle times for improved productivity.
• Ideal for intermittent duty cycles.
• Works well with long extension cords or generator-driven electrical power supplies.
• 115 VAC 50/60-cycle universal motor will operate under poor voltage supply.
• 24 VAC remote motor control with 10 ft (3 m) cord for operator safety.
• Starts under full load.
• High-strength shroud with integral handle protects the motor from contamination and damage.

• Spare Part(s): PUD1100BK