Hydraullic Units

EP RACH-608

EP RACL204

RACL-Series Aluminum Cylinders include a lock nut that gives the reassurance of safe mechanical load holding for extended periods. Each cylinder is single-acting with a high-strength return spring for rapid retraction. The integral stop ring prevents plunger over-travel. All are equipped with bolt-on hardened steel saddles and a steel base plate for increased durability.

Enerpac RACL Lock Nut Aluminum Hydraulic Cylinders can change the way you think about your cylinder applications. With approximately half of the weight of equivalent steel models, they combine an impressive power to weight ratio with the convenience of easier transport and positioning. RACL cylinders are rated for 10,000 psi (700 bar) and comply with ASME B30.1.

Aluminum is not only lightweight, but also inherently less corrosive than steel, which makes it a great material for use in many caustic environments. For enhanced protection, Enerpac RACL Aluminum Cylinders are finished with an anodized hard coat finish to resist damage and extend cylinder life.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: RACL
• Stroke Inches: 3.94
• Stroke MM: 100
• SubTypes: Aluminum Lock Nut Cylinder

• Aluminum Lock Nut provides mechanical load holding for extended periods
• Hardened steel stop ring increases cylinder life and resistance to side-loads of up to 5%
• Hard coat finish on all surfaces resists damage and extends cylinder life
• Composite bearings increase cylinder life and side load resistance
• Handles included on all models
• Steel base plate and saddle for protection against load-induced damage
• Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
• High-strength return spring for rapid cylinder retraction
• CR400 coupler and dustcap included on all models
• All cylinders meet ASME B-30.1 standards

EP RAL502

Simplex RAL Series Aluminum Hydraulic Cylinders feature lock nut that provide the reassurance of safe mechanical load holding for extended periods. These are approximately half the weight of steel equivalents and are expertly engineered to withstand tough applications in harsh conditions.

Aluminum is not only lighter, but also inherently less corrosive than steel, which makes it a great material for use in many caustic environments. A carrying handle provided on all RAL cylinders also enhance portability.

Inside the cylinder is a high-strength return spring for plunger retraction and stop rings for protection against blow out. The cylinder exterior is finished with an anodized hard coat to extend cylinder life, and a wiper protects the inner cylinder assembly from dirt, moisture, and other contaminants.

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000

• Product Line: Hydraulic Tools
• Series: RAL
• Stroke Inches: 2
• Stroke MM: 50.8
• SubTypes: Aluminum Locknut Cylinder

• Capacity Imperial Tons: 50
• Capacity KN: 444,8

• Approximately half the weight of steel cylinders
• Lock nut for mechanical load holding for extended periods
• Heavy duty spring delivers fast and full retraction
• Hard anodized coating reduces wear and corrosion
• Stop rings prevent piston blow-out
• Wiper protects inner cylinder from dirt.
• Meets ANSI/ASME B30.1 Safety Standards
• Load tested under 125% of the nominal capacity
• For working pressures up to 10,000 psi (700 bar)

EP RB-10

EP RC-1006

EP RC-101

EP RC-1014

EP RC10K32

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Spring Kit

EP RC-151

EP RC-1510

EP RC-1512

EP RC-1514

EP RC15K31

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Spring Kit

EP RC-252

EP RC-5013

EP RC-51

EP RC-53

EP RC5K33

• Type: Service Kit

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• SubTypes: Spring Kit

EP RCH-1211

EP RCH-202

EP RCH-606

EP RD1610

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000
• Min Bar: 35

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools, Work Holding Tools
• Series: RD
• Stroke Inches: 10.25
• Stroke MM: 260
• SubTypes: General Purpose Cylinder

• Designed for long life, the best choice for production applications
• Unique mounting configurations simplify fixturing
• Baked enamel finish for increased corrosion resistance
• Double-acting operation develops force in both directions, providing maximum versatility
• Plunger wiper reduces contamination, extending cylinder life

• Accessories: AD181, AD182, AD183, AD152

EP RD166

• Type: Hydraulic Cylinders
• Max Bar: 700
• Max PSI: 10000
• Min Bar: 35

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools, Work Holding Tools
• Series: RD
• Stroke Inches: 6.25
• Stroke MM: 159
• SubTypes: General Purpose Cylinder

• Designed for long life, the best choice for production applications
• Unique mounting configurations simplify fixturing
• Baked enamel finish for increased corrosion resistance
• Double-acting operation develops force in both directions, providing maximum versatility
• Plunger wiper reduces contamination, extending cylinder life

• Accessories: AD181, AD182, AD183, AD152

EP RD-46

EP RD-910