Hydraullic Units

EP HP3015

• Type: Cylinder Accessories

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: HP
• SubTypes: Threaded Hollow Saddle

EP HPT1500

The HPT1500 is a manually operated high-pressure hydraulic tensioner pump in a convenient portable format. With no need for trailing power cords or air hoses, the HPT1500 is ideal for bolt tensioning applications where there is no power source available.

This high-pressure hand pump creates a maximum working pressure of 21,750 psi (1500 bar), and the robust, but lightweight construction provides greater portability than powered tensioner pumps.

To minimize cycle times, the two-speed operation displaces a large volume of oil per stroke at the first stage, and the included pressure gauge keeps you fully informed throughout the process.

Important: These pumps operate at ultra high-pressure, use only the specified fittings and hoses designed for these pressures.

• Type: Hydraulic Pump
• Max Bar: 1500
• Max PSI: 21750

• Product Group: Bolt Tensioner Pumps, Bolt Tensioners
• Product Line: Industrial Tools, Bolting Tools
• Series: HPT
• SubTypes: Hand Pump - Tensioning Pump

• The Enerpac HPT high-pressure Hand Pump is ideally suited for use with hydraulic bolt tensioning tools and hydraulic nuts
• Lightweight and portable high-pressure hand pump
• Two-speed operation displaces a larger volume of oil per stroke, reducing cycle times for many testing applications
• Includes a gauge and coupler for direct connection to GT-Series bolting tools
• Integrated relief valve set at 21,750 psi
• These products operate at ultra-high pressure, use only the specified fittings and hoses designed for these pressures

EP IC-50

EP IC-51

EP IPA5073

• Type: Hydraulic Press
• Max Bar: 700
• Max PSI: 10000

• Product Group: Presses
• Product Line: Industrial Tools
• Series: IP
• SubTypes: H-Frame Press

• Capacity Imperial Tons: 50
• Capacity KN: 498

• Quality welded frame for maximum strength and long life
• Exclusive Hydra-Lift bed for effortless adjustment of the vertical daylight (10-ton models are manual)
• Roller head design is standard to allow movement and locking of the cylinder from side to side(10-ton, 25-ton, and 30-ton are manual)
• All models in the Quick Selection Chart have been matched to a pump, cylinder, hoses and gauge, offering the complete package

• Set Includes: RR5013, ZA4408MX, GF50P, HC9306, GA2
• Accessories: PK1002, A150, IPL100

EP IPE1215

• Type: Hydraulic Press
• Max Bar: 700
• Max PSI: 10000

• Product Group: Presses
• Product Line: Industrial Tools
• Series: IP
• SubTypes: H-Frame Press

• Capacity Imperial Tons: 10
• Capacity KN: 101

• Quality welded frame for maximum strength and long life
• Exclusive Hydra-Lift bed for effortless adjustment of the vertical daylight (10-ton models are manual)
• Roller head design is standard to allow movement and locking of the cylinder from side to side(10-ton, 25-ton, and 30-ton are manual)
• All models in the Quick Selection Chart have been matched to a pump, cylinder, hoses and gauge, offering the complete package

• Set Includes: RC1010, ZE2208MB, GF10P, HC9306, GA2
• Accessories: IPK1012, A136

EP IPH100D13-2

• Type: Hydraulic Press
• Max PSI: 10000

• Product Group: Presses
• Series: IP
• SubTypes: H-Frame Press

• Capacity Imperial Tons: 100

• Set Includes: RR10013, GA3, GF871P, HC9306

EP JBI25

• Type: Cylinder Accessories

• Product Group: Cylinders and Jacks
• Product Line: Industrial Tools
• Series: JBI
• SubTypes: Base Plate

EP L119110SR

• Type: Service Kit

• SubTypes: Spring Kit

EP L748900SR

• Type: ERP

• SubTypes: Saddle Kit

EP LGH314

• Type: Puller
• Max PSI: 10150

• Product Group: Pullers
• Product Line: Industrial Tools
• Series: LGH
• SubTypes: Lock-Grip Puller Hydraulic

• Capacity Imperial Tons: 14
• Capacity KN: 125

• LGH-Series Pullers provide the same safety and ease of use as their mechanical counterparts, with the pulling force applied by a standard 10,150 psi hydraulic cylinder.
• Quickly and easily mount on a wide range of applications
• Turning the puller handle locks the jaws onto the application, allowing the desired object to be pulled free when the spindle is turned.
• Hydraulically applied pulling force increases pulling capacity, reducing operator fatigue
• Lock-on jaws offer a secure grip for safe and easy operation
• Synchronous jaw movement enables entire pulling job to be performed by a single operator
• LGH-Series Pullers MUST be used with a point protector if the shaft end does not contain a drilled center hole. One point protector is included with every puller.
• Always wear safety goggles and gloves while using pullers.

• Set Includes: RWH121, FZ1065, LGH14K6

EP LGHMS324H

• Type: Puller
• Max PSI: 10150

• Product Group: Pullers
• Product Line: Industrial Tools
• Series: LGHMS
• SubTypes: Lock-Grip Master Puller Sets

• Capacity Imperial Tons: 24
• Capacity KN: 215

• All LGHMS-Series Master Puller Sets include an LGH-Series Puller, a Cross Puller, a Bearing Separator, a Bearing Cup Puller, a detachable Hollow Cylinder, a hose, a gauge and a pump
• LGH-Series Pullers provide the same safety and ease of use as their mechanical counterparts, with the pulling force applied by a standard 10,150 psi hydraulic cylinder.
• Quickly and easily mount on a wide range of applications
• Hydraulically applied pulling force increases pulling capacity, reducing operator fatigue
• Lock-on jaws offer a secure grip for safe and easy operation
• Synchronous jaw movement enables entire pulling job to be performed by a single operator
• LGH-Series Pullers MUST be used with a point protector if the shaft end does not contain a drilled center hole. One point protector is included with every puller.
• Enerpac cylinders and pumps can be operated to 10,150 psi, but should not be operated past 5,000 psi when using the Cross Bearing Puller Set tools.
• Always wear safety goggles and gloves while using pullers.

• Set Includes: LGH324, RCH202, HP2015, LGH24K6, BHP272, BHP292, BHP280, P392, GA45GC, HC7206C

EP LH-2506

EP LH50

• Type: Tension Meter and Load Cell

• Product Group: Presses
• Product Line: Industrial Tools
• Series: LH
• SubTypes: Direct Mounted Load Cell

• Accuracy, plus/minus2% of full scale
• Zinc and bronze plated to resist rust and corrosion
• Dual-range readout in kilograms and pounds
• Cushioned metal case provides safe storage and transport
• Maximum indicating pointer reading for pre-selected forces or to maintain maximum force readings
• TM and LH models are 100% tested to verify accuracy within a plus/minus2% range. If your application requires a calibrated tool, it must be submitted for certification testing. Certification is NOT available from Enerpac.

EP LH5006

• Type: Tension Meter and Load Cell

• Product Group: Presses
• Product Line: Industrial Tools
• Series: LH
• SubTypes: Remote Mounted Load Cell

• Accuracy, plus/minus2% of full scale
• Zinc and bronze plated to resist rust and corrosion
• Dual-range readout in kilograms and pounds
• Cushioned metal case provides safe storage and transport
• Maximum indicating pointer reading for pre-selected forces or to maintain maximum force readings
• TM and LH models are 100% tested to verify accuracy within a plus/minus 2% range. If your application requires a calibrated tool, it must be submitted for certification testing. Certification is NOT available from Enerpac.

EP LH5006K

• Type: Service Kit

• SubTypes: Seal Kit

EP P-141

EP P-202

EP P-391

EP P45138

• Type: Service Kit

• SubTypes: Screw

EP P-50

EP P6011

• Type: Service Kit

• SubTypes: Nut

EP P-77

EP PA-133

EP PARG1105N

Enerpac Turbo II Air Over Hydraulic Pumps generate the hydraulic pressure you need using the air pressure you have available. The Air Saver Piston reduces air consumption, and the pump can start at low pressures from 50-125 psi.

Turbo II Air-Hydraulic Pumps are best suited to medium or lower cycle applications. They provide all the power and speed needed for simple clamping circuits and mostly single acting tools. At only 75 dBA, the Turbo II Series helps to keep the noise level to a minimum.

Choose from a range with maximum working pressure of either 5,000 or 10,000psi, and various reservoir capacities from 116 - 462 in3 (2100 - 7500 cm3).

Each PARG pump variant includes a 3-way, 3-position valve for Advance / Hold / Retract functions.

Turbo II Air Over Hydraulic Pump Series :

• PATG - Treadle for foot or hand operation
• PARG - Pendant Operation
• PAMG - Manual lever operated. For double-acting applications
• PACG - For remote valve mount. For work holding, 5000 psi (350 bar).
• PASG - Includes mount for a single DO3 Valve.

• Type: Hydraulic Pump
• Max Bar: 700
• Max PSI: 10000

• Product Group: Pumps
• Product Line: Industrial Tools
• Series: PARG
• SubTypes: Air Pump

• High efficiency cast aluminum air motor for increased life and reduced air consumption
• Reinforced heavy-duty reservoir for applications in tough environments
• New generation air saver piston with rugged one-piece design reduces air consumption and operating costs
• Return-to-tank port for use in remote valve applications
• Quiet - only 76dBA with low air consumption of 12 scfm
• Operating air pressure: 40-125 psi, enables pump to start at extremely low pressure
• Internal pressure relief valve provides overload protection