Search
CLECO S10555
CLECO S10555 branded products
Adapter
DC 14-1144
DC 14-1144
ADAP THREADFor use with PSA Disc holders
- For use with PSA Disc holders
$51.00
Router Guide
DC 14-2413
DC 14-2413
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to minimum order quantities
$120.00
Housing
DC 14-2426
DC 14-2426
HSG ROUTER NOSEFor use with Dotco 12-10, 12-20 and 12-25 series
- For use with Dotco 12-10, 12-20 and 12-25 series
$121.00
Router Guide
DC 14-2501
DC 14-2501
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to minimum order quantities
$120.00
Router Guide
DC 14-2511
DC 14-2511
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to minimum order quantities
$120.00
Guide
DC 14-2600
DC 14-2600
GUIDE ROUTER- For use on Dotco 12-10, 12-20, 12-20, 12-25 and 12-40 series.
- The minimum router bit length (OAL) to be used is determined by the formula: OAL = 1-13/16 (series 12-10) OAL = 2 (series 12-20 & 12-25).
- Important: Insert bit into collet as far as possible, then pull out 1/16 and tighten collet.
- In an emergency, if it is necessary to pull out the bit more than 1/4, be sure to insert a short length of blank shank (not to exceed 5/8 long) in the bottom of the collet before inserting the bit.
- May be subject to minimum order quantities
$120.00
4in Carbide Tip Blade
DC 14-2700
DC 14-2700
BLADE CARB TIP 20TUsed on Cleco Dotco Saws
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
- Used for sawing non-metallic materials
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
$398.00
Saw Blade
DC 14-2710
DC 14-2710
BLADE CARB TIP 20TUsed on Cleco Dotco Saws
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
- Used for sawing non-metallic materials
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
$388.00
Saw Blade
DC 14-2711
DC 14-2711
BLADE CARB TIP 12TUsed on Cleco Dotco Saws
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
- Used for sawing non-metallic materials
CAUTION: These carbide chip and tip and diamond blades are not to be used on metallic materials. Slim blade for easy cutting of fiberglass, with minimum dust -36 grit on periphery and 80 grit on the sides.
$398.00
Drill PG, 29K, 1/4in Jacobs
DC 14CFS90-38
DC 14CFS90-38
DRILL PG,29K,1/4in JACOBS0.4hp / 0.30kW 600-29000rpm
Exhaust: Rear
Tool Configuration: Pistol
Type Housing: Composite
Weight (lbs): 1.54 lb
All tools performance rated @ 90psi / 620 kPa air pressure. Air inlet size: 1/4in Minimum Hose I.D.: 5/16in / 7.9mm Drill Diameter Capacity Matches Chuck Size
- Equipped with Jacobsgeared chuck and chuck key
- Non-reversible
- Non-reversible
- Excellent for aerospace, metal fabrication, and wood working application
Exhaust: Rear
Tool Configuration: Pistol
Type Housing: Composite
Weight (lbs): 1.54 lb
All tools performance rated @ 90psi / 620 kPa air pressure. Air inlet size: 1/4in Minimum Hose I.D.: 5/16in / 7.9mm Drill Diameter Capacity Matches Chuck Size
$718.10
Drill
DC 14CFS91-38
DC 14CFS91-38
DRILL PG,5.2K,1/4in JACOBS0.4hp / 0.30kW 600-29000rpm
Exhaust: Rear
Tool Configuration: Pistol
Type Housing: Composite
Weight (lbs): 1.54 lb
All tools performance rated @ 90psi / 620 kPa air pressure. Air inlet size: 1/4in Minimum Hose I.D.: 5/16in / 7.9mm Drill Diameter Capacity Matches Chuck Size
- Equipped with Jacobsgeared chuck and chuck key
- Non-reversible
- Non-reversible
- Excellent for aerospace, metal fabrication, and wood working application
Exhaust: Rear
Tool Configuration: Pistol
Type Housing: Composite
Weight (lbs): 1.54 lb
All tools performance rated @ 90psi / 620 kPa air pressure. Air inlet size: 1/4in Minimum Hose I.D.: 5/16in / 7.9mm Drill Diameter Capacity Matches Chuck Size
$726.70
Drill Pg, 1.3K, 3/8In Jacobs
DC 14CSL95-51
DC 14CSL95-51
DRILL PG,1.3K,3/8in JACOBS0.6hp / 0.45kW 500-20000rpm
Tool Configuration: Pistol
Type Housing: Composite
Weight (lbs): 2.87 lb
All tools performance rated @ 90psi / 620 kPa air pressure. Air inlet size: 1/4in Minimum Hose I.D.: 5/16in / 7.9mm Drill Diameter Capacity Matches Chuck Size
- Equipped with Jacobsgeared chuck and chuck key
- Ergnomically critical finger and thumb guides fir the hand to aid control
- 1/2in models equipped with dead handle
Tool Configuration: Pistol
Type Housing: Composite
Weight (lbs): 2.87 lb
All tools performance rated @ 90psi / 620 kPa air pressure. Air inlet size: 1/4in Minimum Hose I.D.: 5/16in / 7.9mm Drill Diameter Capacity Matches Chuck Size
Call for pricing
Right Angle Drill
DC 15LF282-62
DC 15LF282-62
DRILL ANGLE,RE,4K,1/4-28I0.4hp / 0.30kW 600-5300rpm Ideal for Restricted Access Applications
Exhaust: Rear
Tool Configuration: Right Angle
Type Housing: Composite
Weight (lbs): 1.6 lb
All tools performance rated @ 90psi / 620 kPa air pressure. Air inlet size: 1/4in Minimum Hose I.D.: 1/4in / 6.4mm
- Wide array of speeds, head designs, and spindle threads for all applications
- High efficiency motor and geartrain
- -62 1/4" -28 Internal thread standard
- Other terminations available: -61 10-32 Internal Thread -63 Threaded Collet -64 5/16" -24 Internal Thread
- Lock off safety lever standard
Exhaust: Rear
Tool Configuration: Right Angle
Type Housing: Composite
Weight (lbs): 1.6 lb
All tools performance rated @ 90psi / 620 kPa air pressure. Air inlet size: 1/4in Minimum Hose I.D.: 1/4in / 6.4mm
$1,302.90
Angle Drill, 45, 3300 Rpm, 1/4-28 Internal Thread
DC 15LF283-42
DC 15LF283-42
Angle Drill, 45, 3300 Rpm, 1/4-28 Internal Thread
$1,350.20
Right Angle Drill
DC 15LS282-62
DC 15LS282-62
DRILL ANGLE,RE,3370 RPM,1/4-28I0.6hp / 0.45kW 500-5400 rpm Ideal for Restricted Access Applications
Exhaust: Rear
Tool Configuration: Right Angle
Type Housing: Composite
Weight (lbs): 2.3 lb
All tools performance rated @ 90psi / 620 kPa air pressure. Air inlet size: 1/4in Standard Equipment: 600 Series Mini Angle Head with 1/4-28 internal thread
- Wide array of speeds, head designs, and spindle threads for all applications
- High efficiency motor and geartrain
- High efficiency motor and geartrain
- Comfortable and ergonomic handle
- Lock off safety lever standard
Exhaust: Rear
Tool Configuration: Right Angle
Type Housing: Composite
Weight (lbs): 2.3 lb
All tools performance rated @ 90psi / 620 kPa air pressure. Air inlet size: 1/4in Standard Equipment: 600 Series Mini Angle Head with 1/4-28 internal thread
$1,646.90
Ratchet, 1/2 Inch Drive 90 Tooth Flex Head Teardrop 17 Inch
GW 81306T
GW 81306T
Ratchet, 1/2 Inch Drive 90 Tooth Flex Head Teardrop 17 Inch
$100.42
Ratchet, 3/8 Inch Drive 90 Tooth Flex Head Teardrop 11 Inch
GW 81215T
GW 81215T
Ratchet, 3/8 Inch Drive 90 Tooth Flex Head Teardrop 11 Inch
$83.68
Combo Wrench, 12PT Long, 41mm Pattern Satin
GW 81841
GW 81841
Combo Wrench, 12PT Long, 41mm Pattern Satin
$119.59
1/2in DRIVE 18MM STANDARD IMPACT SOCKET
GW 84530N
GW 84530N
1/2in DRIVE 18MM STANDARD IMPACT SOCKET
$0.00
Torque Wrench, 100-600 Ft Lbs 3/4 in Drive
GW 85065
GW 85065
Torque Wrench, 100-600 Ft Lbs 3/4 in Drive
$1,638.32
1/2in Dr. Torque Wrench Electric, 25.1 - 250.8 Ft. Lb.
GW 85077
GW 85077
1/2in Dr. Torque Wrench Electric, 25.1 - 250.8 Ft. Lb.
$450.37
3/4in DR ETW TORQUE WRENCH, 75-700 FT/LB
GW 85082
GW 85082
3/4in DR ETW TORQUE WRENCH, 75-700 FT/LB
$2,414.11
Set Wrench Ratcheting Combo Flex, Metric, 16 PC
GW 9902D
GW 9902D
Set Wrench Ratcheting Combo Flex, Metric, 16 PC
$567.46
1268 PC MTS IN MODULAR TRAYS W/STORAGE
GW MEGAMOD1268
GW MEGAMOD1268
1268 PC MTS IN MODULAR TRAYS W/STORAGE
Call for pricing
247 PC MTS in Modular Trays w/Storage
GW MEGAMOD247
GW MEGAMOD247
247 PC MTS in Modular Trays w/Storage
$4,012.44
Payment options
